Panasonic Alert annunciation unit 1736 Parts list manual

Technical Description
1736
Rev 1.0
Alert Annunciation Unit
1736
S/W Ver. 1.4.x
MA441 August 2012

This page has deliberately been left blank.

Technical Description
AAU 1736 –Rev 1
2
Table of contents
1Introduction____________________________4
2Definitions / Explanations ________________5
3General description _____________________6
3.1 Alert Annunciation Unit 1736 ____________________ 6
3.1.1 SW mode 1736 - 1587 _____________________ 6
4Selective Fire alarm presentation __________8
4.1 Alert Annunciation Unit 1736 ____________________ 8
5LED indicators, Push buttons, etc. ________10
5.1 Alert Annunciation Unit 1736 ___________________ 10
6SW mode & Address setting _____________13
6.1 SW mode setting ____________________________ 13
6.1.1 SW mode setting via jumper "J4" ____________ 14
6.2 Address setting _____________________________ 14
6.2.1 Address setting mode via the C.I.E. __________ 14
6.3 Flow chart _________________________________ 15
7User definable text messages (alarm texts)_16
8Commissioning of a new unit / SSD download17
9Restart _______________________________19
10 Fault messages________________________21
10.1 Fault messages in the AA unit __________________ 21
10.2 Fault messages in the C.I.E. ___________________ 21
10.2.1 System FT512 __________________________ 21
10.2.2 System FT128 __________________________ 22
10.2.3 System FT1020G3 _______________________ 22
11 Software (SW) _________________________23
11.1 SW version ________________________________ 23
11.2 SW download_______________________________ 24
12 Operation_____________________________25
13 Connections __________________________26
14 Technical data_________________________29
14.1 Power supply_______________________________ 29
14.2 RS485 ____________________________________ 29
14.2.1 Cable _________________________________ 29
14.3 RS232 ____________________________________ 29
14.4 Connection ________________________________ 29
14.5 Current consumption _________________________ 29
15 Revision history _______________________31

Technical Description
AAU 1736 –Rev 1
3
List of Tables
Table 1 of LED indicators:............................................................... 11
Table 2 push buttons:......................................................................12
Table 3 Buzzer and LCD:................................................................12
Table 4 Current Consumption .........................................................30
List of Figures
Figure 1. The Alert Annunciation Unit (AAU) 1736........................... 6
Figure 2. The Alert Annunciation Unit (AAU) 1736 neutral front..... 10
Figure 3. Operation summary for the AA unit 1735........................ 26
Figure 4. Alert Annunciation units 1736 Connections.....................27
Figure 5. 1736 PCB position of terminal block "J1", jumper "JP8" 27

Technical Description
AAU 1736 –Rev 1
4
1 Introduction
This document describes the Alert Annunciation Unit 1736.
For a detailed description of the AA function, see Technical and Operation
Manuals for the system respectively.
The Alert annunciation unit 1736 shall run in SW mode 1736 –1587.
See also chapter "General description", page 6.
This document is valid for the 1736 software version 1.4.x.
The Alert annunciation unit 1736 can be used in the systems FT512, FT128
and FT1020G3.
In system FT1020G3 the 1736 software version > 1.4.x. must be used.

Technical Description
AAU 1736 –Rev 1
5
2 Definitions / Explanations
Definitions / explanations / abbreviations / etc. frequently used or not
explained elsewhere in the document.
AA Alert Annunciation
AAU Alert Annunciation Unit
AA alarm Alert Annunciation alarm
AA function Alert Annunciation function
C.I.E. Control and indicating equipment (=control unit)
C.U. Control unit (=Control and indicating equipment)
SW Software
HW Hardware

Technical Description
AAU 1736 –Rev 1
6
3 General description
When the Alert Annunciation function shall be used in the systems FT512,
FT128 and FT1022G3, one or more AA units are required to present the AA
alarms and for the related manoeuvres, i.e. to acknowledge / reset the AA
alarms.
The LED "L6" (Operation) is indicating if the "Alert Annunciation" function is
enabled or disabled
1
.
When the AA function is enabled ("L6" on) and a fire alarm in the system, the
LED "L3" (Fire brigade alerted) is indicating whether the alarm is an AA alarm
or normal alarm.
LED L3 will be OFF for AA alarm and ON for non - AA alarm / Output "Fire
brigade tx" activated.
The LED "L4" (Acknowledged) is indicating if the AA alarm has been
acknowledged. See also chapter "Operation", page 25.
3.1 Alert Annunciation Unit 1736
Figure 1. The Alert Annunciation Unit (AAU) 1736.
The Alert Annunciation Unit consists of a compact size enclosure made of
grey (RAL 7035) high impact ABS, with temperature resistance up to 85° C.
Fitted with a supplementary "O" ring gasket, it will comply with IP65, in respect
of dust and moisture. The unit has no door, i.e. the front is accessed directly,
when required. The push buttons are disabled until an AA alarm is activated.
The unit shall be wall mounted. The unit is intended for indoor use and in dry
premises. Two compression glands (IP67) for cable inlets are attached.
3.1.1 SW mode 1736 - 1587
The Alert Annunciation Unit 1736 must run in SW mode 1736 –1587.
In system FT512, 1736 units running in SW mode 1736 –1587 have to be
connected to a DU interface board 1587 mounted in the FT512 C.I.E.
1
The AA function is normally enabled (during daytime) / disabled (during night-time)
via a time channel.

Technical Description
AAU 1736 –Rev 1
7
In system FT128, 1736 units running in SW mode 1736 –1587 are connected
directly to the main board connector "J1" or via the termination board terminal
15 & 16 (Australian convention) but an optional RS485 transceiver
component (chip) 4552 is required on the main board.
In system FT1020G3, 1736 units running in SW mode 1736 –1587 are
connected directly to the main board connector "J4". No additional interface
required.

Technical Description
AAU 1736 –Rev 1
8
4 Selective Fire alarm presentation
Normally all fire alarms will be presented in the C.I.E’s, external FBP’s,
Presentation units, etc. There are some possibilities to select which alarms
that shall be presented in each unit. It is also programmable, i.e. when only
one point in a zone is in alarm status it will be presented as a point alarm
(zone and address), else presented as a zone alarm.
4.1 Alert Annunciation Unit 1736
The alarm presentation in an AA unit will be similar to the one in the C.I.E. that
the AA unit is connected to, i.e. point alarm or zone alarm presentation. See
Operation Manual, chapter "Fire alarm" for each system.
Via Win512 / Win128 / WinG3, it is possible to select which alarms that shall
be presented in the AA unit respectively. For example, if there are many
buildings in an installation, the AA unit in one specific building shall only
present alarms activated within this building.
The following, so called operands are available (CU alternatives not valid for
FT128):
1. Control unit (CU)
2. Consecutive control units (CU1, CU2)
3. Zone (zone)
4. Consecutive zones (zone1, zone2)
5. Zone –address (zone, addr)
6. Consecutive zone –addresses (zone1, addr1, zone2, addr2)
Explanations:
1. CU = Control unit number (C.I.E. no. 00-29)
2. CU1 = The first control unit number in the sequence. CU2 = The
last control unit number in the sequence.
3. zone = Zone number (001-999) In FT128 (01-32).
4. zone1 = The first zone number in the sequence. zone2 = The last
zone number in the sequence.
5. zone, addr = Zone number and address within the zone (001, 01 –
999, 99)
6. zone1, addr1 = The first zone number and address in the
sequence. zone2, addr2 = The last zone number and address in
the sequence.
Up to 50 operands can be used to make a selector for an AA unit. Here
follows a selector example:
Control unit (00), Consecutive zones (100, 500), Zone –address (900, 01)
In this AA unit will only be presented alarms originated from the C.I.E. no. 00
or from zone 100 up to and including zone 500 or from the alarm point 900-01.
Default for each AA unit is, in system FT512 and FT1020G3: Control units
(00, 29), i.e. all alarms from all C.I.E.:s will be presented in all AA units.

Technical Description
AAU 1736 –Rev 1
9
Default for each AA unit is, in system FT128: Zones (01 - 32), i.e. all alarms
will be presented in all units.