Panasonic KX-HNS105AZ User manual

Installation Guide
Home Network System
Indoor Siren
Model No. KX-HNS105AZ
Thank you for purchasing a Panasonic product.
This document explains how to install the indoor siren properly.
For details about how to use the system, refer to the User’s Guide
(page 13).
Please read this document before using the unit and save it for future
reference.
HNS105AZ_(en_en)_0622_ver.001.pdf 1 2015/06/22 20:09:47

Introduction
Accessory information ...............3
Important Information
About this system ......................4
For your safety ...........................4
Important safety instructions ......6
For best performance ................6
Other information .......................6
Setup
Part names and functions ..........8
LED indicator .............................8
Setup overview ..........................8
Registering the siren ..................9
Confirming the usage area ......10
Installation ...............................10
Note about power
connections .............................12
Appendix
Testing the siren ......................13
Adjusting the siren’s volume ....13
Features available when using the
[Home Network] app ................13
Accessing the User’s Guide ....13
Specifications ..........................14
Warranty (for New Zealand) ....15
2
Table of Contents
HNS105AZ_(en_en)_0622_ver.001.pdf 2 2015/06/22 20:09:47

Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
AAC adaptor/PNLV236AL 1
BDC extension cord 1
CWall mounting screws (25 mm) 2
A B C
Other information
RDesign and specifications are subject to change without notice.
RThe illustrations in these instructions may vary slightly from the actual product.
Trademarks
RiPhone and iPad are trademarks of Apple Inc., registered in the U.S. and other
countries.
RAndroid is a trademark of Google Inc.
RMicrosoft, Windows, and Internet Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
RAll other trademarks identified herein are the property of their respective owners.
3
Introduction
HNS105AZ_(en_en)_0622_ver.001.pdf 3 2015/06/22 20:09:47

About this system
RThis system is an auxiliary system; it
is not designed to provide complete
protection from property loss.
Panasonic will not be held
responsible in the event that
property loss occurs while this
system is in operation.
RThe system’s wireless features are
subject to interference, therefore
functionality in all situations cannot
be guaranteed. Panasonic will not
be held responsible for injury or
damage to property that occurs in
the event of wireless communication
error or failure.
For your safety
To prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Power connection
RUse only the power source marked
on the product.
RDo not overload power outlets and
extension cords. This can result in
the risk of fire or electric shock.
RCompletely insert the AC adaptor/
power plug into the power outlet.
Failure to do so may cause electric
shock and/or excessive heat
resulting in a fire.
RRegularly remove any dust, etc.
from the AC adaptor/power plug by
pulling it from the power outlet, then
wiping with a dry cloth. Accumulated
dust may cause an insulation defect
from moisture, etc. resulting in a fire.
RUnplug the product from power
outlets if it emits smoke, an
abnormal smell, or makes an
unusual noise. These conditions can
cause fire or electric shock. Confirm
that smoke has stopped emitting
and contact an authorised service
centre.
RUnplug from power outlets and
never touch the inside of the product
if its casing has been broken open.
Danger of electric shock exists.
RNever touch the plug with wet
hands. Danger of electric shock
exists.
RDo not connect non-specified
devices.
Installation
RTo prevent the risk of fire or
electrical shock, do not expose the
product to rain or any type of
moisture.
RDo not place or use this product
near automatically controlled
devices such as automatic doors
and fire alarms. Radio waves
emitted from this product may cause
such devices to malfunction
resulting in an accident.
RDo not allow the AC adaptor to be
excessively pulled, bent or placed
under heavy objects.
RInstall the product only on a vertical
surface. Do not install the product on
a ceiling, as the product may fall,
resulting in damage or injury.
RKeep small parts (screws, etc.) out
of the reach of children. There is a
risk of swallowing. In the event they
are swallowed, seek medical advice
immediately.
4
Important Information
HNS105AZ_(en_en)_0622_ver.001.pdf 4 2015/06/22 20:09:47

RIt is advised not to use the
equipment at a refuelling point.
Users are reminded to observe
restrictions on the use of radio
equipment in fuel depots, chemical
plants or where blasting operations
are in progress.
Operating safeguards
RUnplug the product from power
outlets before cleaning. Do not use
liquid or aerosol cleaners.
RDo not disassemble the product.
RNever put metal objects inside the
product. If metal objects enter the
product, turn off the circuit breaker
and contact an authorised service
centre.
Medical
RConsult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. DECT features
operate between 1.88 GHz and
1.90 GHz with a peak transmission
power of 250 mW.
RDo not use the product in health
care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment
that could be sensitive to external
RF energy.
CAUTION
Installation and location
RNever install wiring during a lightning
storm.
RThe AC adaptor is used as the main
disconnect device. Ensure that the
AC outlet is installed near the
product and is easily accessible.
RTo avoid the risk of strangulation,
keep the product and the AC
adaptor cord at least 1 m from a
child’s crib and out of the reach of
small children.
Preventing accidents and injuries
RDo not put your ear(s) near the
product, as loud sounds emitted
from the product may cause hearing
impairment.
RDo not look directly at the strobe
light when it is flashing. Light emitted
from the strobe light may cause
damage to the eyes.
RConsider the installation
environment carefully when
installing the product. Pay particular
attention to infants, children, and the
elderly, as they may be more
sensitive to loud sounds and strobe
lights.
General notices
RThis equipment will be inoperable
when mains power fails.
RWhen a failure occurs which results
in the internal parts becoming
accessible, disconnect the power
supply cord immediately and return
this unit to an authorised service
centre.
RTo minimise the possibility of
lightning damage, when you know
that a thunderstorm is coming, we
recommend that you unplug the AC
adaptor from the AC power outlet.
5
Important Information
HNS105AZ_(en_en)_0622_ver.001.pdf 5 2015/06/22 20:09:47

Important safety
instructions
When using your product, basic safety
precautions should always be followed
to reduce the risk of fire, electric shock,
and injury to persons, including the
following:
1. Do not use this product near water
for example, near a bathtub,
washbowl, kitchen sink, or laundry
tub, in a wet basement or near a
swimming pool.
2. Use only the power cord indicated
in this document.
SAVE THESE INSTRUCTIONS
For best performance
Hub location/avoiding noise
The hub and other compatible
Panasonic devices use radio waves to
communicate with each other.
RFor maximum coverage and
noise-free communications, place
your hub:
– at a convenient, high, and central
location with no obstructions
between the product and hub in
an indoor environment.
– away from electronic appliances
such as TVs, radios, personal
computers, wireless devices, or
other phones.
– facing away from radio frequency
transmitters, such as external
antennas of mobile phone cell
stations. (Avoid putting the hub
on a bay window or near a
window.)
RIf the reception for a hub location is
not satisfactory, move the hub to
another location for better reception.
Environment
RKeep the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
RThe product should be kept free
from excessive smoke, dust, high
temperature, and vibration.
RThe product should not be exposed
to direct sunlight.
RDo not place heavy objects on top of
the product.
RWhen you leave the product unused
for a long period of time, unplug the
product from the power outlet.
RThe product should be kept away
from heat sources such as radiators,
cookers, etc. It should not be placed
in rooms where the temperature is
less than 0 °C or greater than 40 °C.
Damp basements should also be
avoided.
ROperating the product near electrical
appliances may cause interference.
Move away from the electrical
appliances.
Other information
Routine care
RWipe the outer surface of the
product with a soft moist cloth.
RDo not use benzine, thinner, or any
abrasive powder.
6
Important Information
HNS105AZ_(en_en)_0622_ver.001.pdf 6 2015/06/22 20:09:47

Information on Disposal in other
Countries outside the European
Union
These symbols are only valid in the
European Union. If you wish to discard
these items, please contact your local
authorities or dealer and ask for the
correct method of disposal.
7
Important Information
HNS105AZ_(en_en)_0622_ver.001.pdf 7 2015/06/22 20:09:47

Part names and
functions
A B D
E
F
C
Horn
Strobe light
Flashes when the siren is
sounding.
LED indicator
MHIGHN/MLOWN
Used to adjust the siren’s volume
(page 13).
Rear cover
M N
Used to register the siren to the
hub.
LED indicator
You can use the LED indicator to
confirm the siren’s status.
Indicator Status
Green, lit Normal operation
Red,
blinking
slowly
Siren is not registered
to a hub
Red,
blinking
Siren is out of range of
the hub
Red,
blinking
quickly
Alarm system was
triggered
Green,
blinking
slowly
Registration mode
(You pressed and held
M N)
Off No power
Setup overview
1Initial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Setup Guide included with your
hub.
2Registration
Required only if the siren was
purchased separately (i.e., not as
part of a bundle).
3Confirm the installation area
Read the information in this
document to confirm that the
desired installation area is suitable
to proper operation.
8
Setup
HNS105AZ_(en_en)_0622_ver.001.pdf 8 2015/06/22 20:09:48

4Installation
Install the siren in the desired
location.
Registering the siren
This procedure is not required for
devices that were included as part of
a bundle.
Before you can use the siren, it must
be registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register each device to the hub.
You can register each device by using
the registration buttons or the [Home
Network] app.
Note:
RBefore registering the siren, make
sure the AC adaptors of the hub and
siren are connected and each
device is powered.
Using registration buttons
1Hub:
Press and hold M OTHER
DEVICEN until the LED indicator
blinks slowly in green.
2Siren:
Press and hold MN until the
LED indicator blinks slowly in
green (page 8).
RWhen registration is complete,
the hub sounds one long beep.
Note:
RTo cancel without registering the
siren, press MN on the hub and
on the siren again.
RIf registration fails, the hub sounds
several short beeps.
Using the app
When you register the siren by using
the [Home Network] app, you can
assign a name to your devices and
group them by location. For more
information, refer to the User’s Guide
(page 13).
9
Setup
HNS105AZ_(en_en)_0622_ver.001.pdf 9 2015/06/22 20:09:48

Confirming the
usage area
Wireless communication
range
The wireless communication range of
each device in the system from the hub
is approximately 50 m indoors and
approximately 300 m outdoors.
Wireless communication may be
unreliable when the following obstacles
are located between the hub and other
devices.
RMetal doors or screens
RWalls containing aluminium-sheet
insulation
RWalls made of concrete or
corrugated iron
RDouble-pane glass windows
RMultiple walls
RWhen using each device on
separate floors or in different
buildings
Note:
RYou can use the siren’s LED
indicator to confirm the siren’s
communication status (page 8). If
the LED indicator is lit in green or is
blinking quickly in red, the siren is
communicating properly with the
hub.
Usage area cautions
Using the siren in the following areas
may cause deformation, malfunction, or
operational failure.
RIn direct sunlight
RAreas exposed to grease or steam,
such as kitchens
RNear fire or heating devices
RNear magnetic fields (such as near
microwaves and magnets)
RAreas subject to extreme
temperature changes, such as next
to air conditioners
RAreas with reflective objects, such
as glass, that can interfere with
detection of temperature variation
RAreas where the temperature is
affected by strong illuminating
objects (such as fluorescent lights)
RNear devices that emit strong radio
waves, such as mobile phones
Installation
Mount the siren on a wall using the
holes in the rear cover.
Note:
RThe strobe light flashes when the
siren sounds. Mount the siren in a
location where its strobe light will be
visible.
RMount the siren on the stable
location where the siren can be
adequately supported when
mounting.
RMount the siren securely to a wall.
Vibrations may cause it to fall if it is
not secured.
RDo not mount siren on a soft
material. It may fall down, break or
cause injury.
RDo not mount the siren on the
following places: gypsum board,
ALC (autoclaved lightweight cellular
concrete), concrete block, plywood
less than 25.4 mm thick, etc.
RUse only the supplied Panasonic AC
adaptor PNLV236AL.
10
Setup
HNS105AZ_(en_en)_0622_ver.001.pdf 10 2015/06/22 20:09:48

1Remove the rear cover by
pressing the upper sides of the
cover (A) and sliding it down (B).
A
B
2Attach the rear cover to the wall by
using screws (
1
).
RPlace the rear cover with “UP”
mark facing upwards.
R
2
37 mm
2
1
1
UP
UP
Note:
RUse the following template
below when determining the
location of the screw holes.
37 mm
11
Setup
HNS105AZ_(en_en)_0622_ver.001.pdf 11 2015/06/22 20:09:48

3Use the DC extension cord (A) to
connect the AC adaptor (B) to the
siren.
RInsert the male plug of the DC
extension cord (C) firmly into
the DC socket (D, E).
RInsert the female plug of the DC
extension cord (F) firmly into
the AC adaptor plug (G).
4Connect the AC adaptor to the
power outlet (H).
5
8
6
7
4
1
3
2
5Attach the siren to the rear cover.
RInsert the grooves on the siren
to the 4 tabs on the rear cover,
and then push down the siren.
Note:
While the siren is sounding or the
strobe light is flashing, you can stop the
siren by pressing MN.
Note about power
connections
AC adaptor connection
RThe AC adaptor must remain
connected at all times. (It is normal
for the adaptor to feel warm during
use.)
RThe AC adaptor should be
connected to a vertically oriented or
floor-mounted AC outlet. Do not
connect the AC adaptor to a
ceiling-mounted AC outlet, as the
weight of the adaptor may cause it
to become disconnected.
Power failure
RThe siren will not work during a
power failure.
12
Setup
HNS105AZ_(en_en)_0622_ver.001.pdf 12 2015/06/22 20:09:48

Testing the siren
After you have installed the [Home
Network] app on your mobile device,
you can use your mobile device to test
the siren. For more information, refer to
the User’s Guide (page 13).
1Start the [Home Network] app,
and tap [Settings].
2Tap [Device Profiles].
3Tap [Siren] and then select the
desired siren.
4Tap [Installation Test].
5Tap [Play].
Adjusting the siren’s
volume
You can adjust the siren’s volume
using the siren’s MHIGHN/MLOWN switch
(page 8).
Features available
when using the
[Home Network] app
Some of the siren’s features that are
available when using the [Home
Network] app are listed below. For
more information, refer to the User’s
Guide (page 13).
–Alarm system
You can use the app to arm and
disarm the alarm system, confirm
the current status of the system’s
devices, and view a log of previous
events. You can also use the app to
stop the siren from sounding.
–Device management
You can use the app to confirm the
wireless signal strength of the siren,
change the siren’s name, change
whether the siren sounds, flashes,
or both, and test the siren.
Accessing the User’s
Guide
The User’s Guide is a collection of
online documentation that helps you
get the most out of the [Home
Network] app.
1iPhone/iPad
Tap in the app’s home screen.
Android™ devices
Tap or press your mobile
device’s menu button in the app’s
home screen.
2Tap [User’s Guide].
Note:
RMicrosoft® Windows® Internet
Explorer® 8 and earlier versions are
not supported.
RAndroid 4.1 or later versions are
recommended.
RYou can also access the User’s
Guide at the web page listed below.
www.panasonic.net/pcc/support/tel/
homenetwork/manual/
13
Appendix
HNS105AZ_(en_en)_0622_ver.001.pdf 13 2015/06/22 20:09:48

Specifications
RStandards
DECT (Digital Enhanced Cordless
Telecommunications)
RFrequency range
DECT: 1.88 GHz – 1.90 GHz
RRF transmission power
DECT: Approx. 10 mW (average
power per channel)
RPower source
220 – 240 V AC, 50/60 Hz
RPower consumption
Standby: Approx. 2.0 W
Maximum: Approx. 3.0 W
RAlert tone volume
Approx. 110 dB (High alert level)
(measured approx. 10 cm from the
product)
ROperating conditions
0 °C – 40 °C
RDimensions (height ´ width ´
depth)
Approx. 71 mm ´ 73 mm ´ 46 mm
RMass (weight)
Approx. 90 g
14
Appendix
HNS105AZ_(en_en)_0622_ver.001.pdf 14 2015/06/22 20:09:48

Warranty (for New Zealand)
Panasonic New Zealand undertakes to:
Repair or at its option, replace without cost to the owner, either formaterial or labour,
part which is found to be defective within two years of the date of purchase.
THIS EXPRESS WARRANTY DOES NOT COVER:
IF YOUR PANASONIC PRODUCT FAILS WITHIN THE
WARRANTY PERIOD:
Take it to the Authorised Panasonic Dealer from whom you purchased the product
will repair it (or arrange to have it repaired) during their normal business
enquiries regarding warranty or otherwise, please call – Customer
eTel. No.: [phone]
NOTE: THIS EXPRESS WARRANTY IS OFFERED AS AN
BENEFIT AND DOES NOT AFFECT YOUR LEGAL
1) Pick up and delivery.
2) Batteries.
3) Repairs when the product has not been used in accordance with the Operating
Instructions Manual or has been modified.
4) Normalmaintenance and cleaning as required in the product’s Operating
Instructions Manual.
5) Service calls to: a Correct the set up of the product
b Instruct you how to use the product
c Replace fuses or correct your building’s wiring
6) Damage to the product caused by accident, misuse or Act of God.
7) Repairs when the product has been dismantled, repaired, modified or serviced
by other than a Panasonic Authorised Dealer authorised to service that type of
product.
any
Centr
All
who
RIGHTS.
EXTRA
Support
hours.
15
Appendix
HNS105AZ_(en_en)_0622_ver.001.pdf 15 2015/06/22 20:09:48

For your future reference
We recommend keeping a record of the following information to assist
with any repair under warranty.
Serial No. Date of purchase
(found inside the unit)
Name and address of dealer
Attach your purchase receipt here.
For Australia
Customer Care Centre Tel. No.: 132600
or website www.panasonic.com/au
For New Zealand
Customer Care Centre Tel. No.: [phone]
or website www.panasonic.com/nz
Sales Department:
1 Innovation Road, Macquarie Park NSW 2113, Australia
Sales Department:
18 Sir Woolf Fisher Drive, Highbrook, East Tamaki, Auckland,
New Zealand
Phone: [phone]
Fax: [phone]
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
© Panasonic System Networks Co., Ltd. 2015
*PNQX7359ZA*
*PNQX7359ZA*
PNQX7359ZA CC0715WK0 (E)
HNS105AZ_(en_en)_0622_ver.001.pdf 16 2015/06/22 20:09:48