Paradox Digiplex DGP2-648 Assembly instructions

for DGP-848 & DGP-NE96 systems
48-Zone LED Keypad V1.0
Installer Guide
DGP2-648
DGP-641
DGP2648_EI06.fm Page -3 Thursday, July 22, 2004 9:15 AM

DGP2648_EI06.fm Page -2 Thursday, July 22, 2004 9:15 AM

Table of Contents
Introduction.........................................................................1
Specifications........................................................................... 1
Installation...........................................................................2
Connecting the Keypad............................................................ 2
Connecting the Keypad Zone................................................... 2
Programmable Output (PGM).................................................. 3
Programming.......................................................................4
Winload Programming.............................................................. 4
System Options...................................................................5
Partition Display....................................................................... 6
Zone Display............................................................................ 7
Section Reset........................................................................... 7
Confidential Mode .................................................................... 8
Exit Confidential Mode............................................................. 8
Confidential Mode Timer.......................................................... 8
Muting ...................................................................................... 9
Beep on Exit Delay................................................................... 9
Chime on Zone Closure........................................................... 9
Beep on Trouble....................................................................... 9
Keypad Anti-tamper Enable................................................... 10
PGM Programming............................................................11
PGM State.............................................................................. 11
PGM Activation Event............................................................ 11
PGM Deactivation Event........................................................ 12
PGM Deactivation Mode........................................................ 12
PGM Base Time..................................................................... 13
PGM Timer............................................................................. 13
PGM Test............................................................................... 13
List of Sections .................................................................14
DGP2648_EI06.fm Page -1 Thursday, July 22, 2004 9:15 AM

DGP2648_EI06.fm Page 0 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 1n
1.0 Introduction
Thank you for choosing Paradox Security Systems. Our advanced
technology security systems provide you with reliable security
protection and powerful features, which are easy to use. The
DGP2-648 keypads allow easy access to the security system’s
functions and its illuminating LEDs provide the system’s status at a
glance.
1.1 Specifications
Power input: 9-16 Vdc, 45mA typical
PGM current limit: 50 mA
Number of inputs: 1
Number of zones: 1 standard zone, no tamper recognition
Power indication: Yellow LED “ON”
Locate indication: Green and yellow LEDs flash
simultaneously
Bus fault indication: Red and yellow LEDs flash alternately
Locate deactivation: Anti-tamper switch
Compatibility: Any DGP-848/DGP-NE96 control panel.
Winload (V2.20 onwards)
DGP2648_EI06.fm Page 1 Thursday, July 22, 2004 9:15 AM

2 Reference & Installation Manual
2.0 Installation
2.1 Connecting the Keypad
The LED keypad is connected to the control panel’s communication
bus in a star and/or daisy chain configuration. The four-wire
communication bus provides power and two-way communication
between the control panel and all modules connected to it. Connect the
four terminals labeled red, black, green and yellow of the keypad to
the corresponding terminals on the control panel as shown in Figure 1
on page 3. Refer to the control panel’s Reference & Installation Manual
for the maximum allowable installation distance from the control panel.
2.2 Connecting the Keypad Zone
Your keypad has one hardwired input terminal, allowing you to
connect one detector or door contact directly to it. For example, you
can wire a door contact located at the entry point of an establishment
directly to the input terminal of the entry point keypad, instead of
wiring the door contact all the way to the control panel.
Connect the device to the keypad's input terminal as shown in Figure
1 on page 3.
The keypad zone follows the control panel’s EOL
definition.
In order to communicate its status to the control panel, devices
connected to the keypad's input terminal must be assigned to a zone
in the control panel and the zone's parameters must be defined.
The control panel does not recognize tampers
originating from the keypad zone.
For more information on zone assignment, please refer to the control
panel's Reference & Installation Manual. Please note that even with
DGP2648_EI06.fm Page 2 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 3n
the ATZ (zone doubling) feature enabled, the keypad supports only
one detection device.
Figure 1: Connecting Keypads and Keypad Zones
2.3 Programmable Output (PGM)
Each keypad has one on-boardPGM. A PGM is a programmable output,
which toggles to its opposite state (i.e. a normally open PGM will close)
when a specific event has occurred in the system (see “PGM Activation
Event” on page 11). Upon activation, the PGM can provide 50mA to any
device connected to it. If the current drawn will exceed the current limit, a
relay should be connected to the PGM as shown in Figure 1 on page 3.
Devices connected to a keypad’s input
terminal must be assigned to a zone,
keyswitch or virtual input in the control panel.
In addition, the zone’s parameters must be
defined. For detailed instructions please refer
to the control panel’s Reference and
Installation Manual.
The keypad zone follows the
control panel’s EOL definition.
The zone speed is set at 600mS
and cannot be changed. Note: The keypad’s anti-
tamper switch will
communicate its status to
the control panel via the
communication bus.
DGP2648_EI06.fm Page 3 Thursday, July 22, 2004 9:15 AM

4 Reference & Installation Manual
3.0 Programming
Program the LED keypad using any LCD keypad on the
communication bus or using the Winload software. We strongly
recommend you read this entire manual before you begin
programming.
This model does not support installer programming
capabilities, therefore you cannot program other
modules or the panel on the communication bus using
this unit.
3.1 Winload Programming
Using the WinLoad Security System Management Software, you can
program control panels and keypads remotely through a modem at
300 baud or on-site at 19.2k/38.4k baud with a 306 Adapter. For
more information refer to the WinLoad OnLine Help.
DGP2648_EI06.fm Page 4 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 5n
4.0 System Options
Figure 2: Keypad Overview
[ENTER]Saves current data and exits current menu.
[CLEAR] Erases current data entry or reverts to the preceding step.
Partition Lights: (A1, A2, A3 and A4)
ON = Partition armed
OFF = Partition disarmed
FLASH = Partition in alarm
Action Lights: (Access, Stay,
Force, Mem, Trbl and Prg)
Lights will illuminate according
to the status of the system.
Numerical Lights: (Zones)
ON = Open / breached
OFF = OK
FLASHES = Tamper / fire loop
“AC” Light:
ON = AC Power
OFF = Power failure
“Status” Light:
When green:
ON = All zones closed
OFF = Zone(s) open
FLASH = Exit Delay in progress
When red:
ON = All partitions armed
OFF = Partition disarmed
FLASH = Partition in alarm
Keypad willdisplay the status of
all its assigned partitions.
DGP2648_EI06.fm Page 5 Thursday, July 22, 2004 9:15 AM

6 Reference & Installation Manual
4.1 Partition Display
Section [001] to [008]
You can program the LED keypad to display up to four partitions.
Sections [001] to [008] correspond to partitions 1 to 8. The LED
numbers A1 to A4 are assigned values 001 to 004 (see section 3). To
assign a display number to a partition, choose a section number from
[001] to [008] and assign it a value between 001 and 004 which
represents LED numbers A1 to A4 respectively.
Figure 3: LED Partition Display
Do not assign the same display number to more than one
section. For example, you cannot assign value 002 to
sections [003] and [004]. The rejection beep will remind you
that a selected display number is already assigned to another
section. Refer to section 6.0 on page 14 for default values.
Example:
LED A3 is assigned to partition 3. To reassign LED A3 to partition 8
perform the following steps:
1) Enter [003] to select partition 3.
2) Enter [000] to clear the value.
Value: 001 002 003 004
DGP2648_EI06.fm Page 6 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 7n
3) Enter [008] to select partition 8.
4) Enter value [003] to reassign display number A3 to partition 8.
5) Press the [CLEAR]key to exit.
4.2 Zone Display
Section [101] To [196]
You can program the keypad to display any zone from 1 to 96 up to a
total of 48. Sections [101] to [196] correspond to zones 1 to 96
respectively. These zones are displayed on LED numbers 1 to 48
and are assigned values 001 to 048.
Do not assign more than one LED number to a zone. For
example, you cannot assign LED number 33 to zones 21 and
28. The rejection beep will remind you that a selected LED
number is already assigned to another section. Refer to
section 6.0 on page 14 for default values.
Example:
LED number 29 is assigned to zone 29. To reassign LED number 29
to zone 47 perform the following steps:
1) Enter [129] to select system zone 29.
2) Enter [000] to clear the value.
3) Enter [147] to select system zone 47.
4) Enter value [029] to reassign LED number 29 to zone 47.
5) Press the [CLEAR]key to exit.
Every time the [CLEAR]key is pressed it will revert to the
preceding step, unless entering in data in which case it will
erase the current entry.
4.3 Section Reset
Section [040]
This section resets zone display sections [101] to [196] to default
settings. Enter [040] to perform the reset.
DGP2648_EI06.fm Page 7 Thursday, July 22, 2004 9:15 AM

8 Reference & Installation Manual
4.4 Confidential Mode
Section [009] Option [1]
The keypad will switch to Confidential Mode after a period of
inactivity (default is 120 sec.) if option [1] is enabled. In Confidential
Mode all LEDs will turn off until either a button is pressed or an
access code is entered (see section 4.5). Once the keypad is
activated, all applicable LEDs will illuminate. Refer to page 11 for
Confidential Mode Timer.
Option [1] OFF = Disabled (default).
Option [1] ON = Enabled.
4.5 Exit Confidential Mode
Section [009] Option [2]
If confidential mode is enabled, option [2] determines how the
keypad will return to normal mode after the keypad has switched to
confidential mode (see section 4.4).
Option [2] ON = Exit Confidential Mode by entering an access code.
Option [2] OFF = Exit Confidential Mode by pressing a button (default).
Option [2] must be set to ON on UL listed systems.
Option [2] will only work if option [1] is enabled.
4.6 Confidential Mode Timer
Section [012]
Section [012] determines the amount of time without action before
the keypad enters Confidential Mode. For more information on
Confidential Mode, refer to “Confidential Mode” on page 8. The
Confidential Mode Timer can be set from 005 seconds to 255
seconds. Default: 120 seconds
DGP2648_EI06.fm Page 8 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 9n
4.7 Muting
Section [009] Option [3]
You can program the keypad not to emit audible sounds, including
Chimed zones. During Muting, the keypad will only emit the
Confirmation Beep, Rejection Beep and beep when users press a
button.
Option [3] OFF = Audible sounds (default).
Option [3] ON = Mute.
4.8 Beep on Exit Delay
Section [009] Option [4]
The keypad can beep once every second during the Exit Delay
Timer. During the final 10 seconds, it will beep more rapidly to
provide a final warning before the partition is armed.
Option [4] OFF = Exit Delay beep disabled.
Option [4] ON = Exit Delay beep enabled (default).
4.9 Chime on Zone Closure
Section [009] Option [5]
During the Chime Zone Time Period that the user sets, the keypad
can emit an intermittent beep whenever a zone with the Chime
feature enabled closes (see the user manual for details on Chime
Zones). If the user does not set the Chime Zone time period and this
option is enabled, the Chime Zones will always beep upon closure.
Option [5] OFF = Chime on Zone Closure disabled (default).
Option [5] ON = Chime on Zone Closure enabled.
4.10 Beep on Trouble
Section [010] Options [1] To [4]
Potential troubles are sorted into groups. With these options enabled,
DGP2648_EI06.fm Page 9 Thursday, July 22, 2004 9:15 AM

10 Reference & Installation Manual
the keypad will emit an intermittent beep whenever a trouble condition
from the Trouble Groups occurs in the system. The intermittent beep
will remain activated until the user enters the Trouble Display or if the
trouble is resolved (see your control panel’s Reference & Installation
Manual for details concerning Trouble Display). The intermittent beep
will reinitialize whenever the trouble reoccurs.
System Troubles / Clock Loss
Option [1] OFF = Disabled (default).
Option [1] ON = Enabled.
Communicator Troubles
Option [2] OFF = Disabled (default).
Option [2] ON = Enabled.
Module / Communication Bus Troubles
Option [3] OFF = Disabled (default).
Option [3] ON = Enabled.
Zone Troubles
Option [4] OFF = Disabled (default).
Option [4] ON = Enabled.
4.11 Keypad Anti-tamper Enable
Section [011] Option [5]
When the tamper option is enabled and the keypad's anti-tamper
switch is triggered, the keypad will send a tamper report to the control
panel via the communication bus. For information on how the control
panel will process the tamper, refer to the tamper recognition options
in your control panel’s Reference and Installation manual.
Option [5] OFF = Keypad's anti-tamper is disabled (default).
Option [5] ON = Keypad's anti-tamper is enabled.
DGP2648_EI06.fm Page 10 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 11n
5.0 PGM Programming
5.1 PGM State
SECTION [011] OPTION [1]
The keypad's on-board PGM can be set as normally open or
normally closed. When an open PGM is activated, it will close the
circuit to the ground and enable any devices connected to it. When a
closed PGM is activated, it will open the circuit and disable any
devices connected to it. When the PGM Activation Event occurs (see
section 5.2), the PGM will switch to its opposite state (i.e. open to
closed or closed to open). The PGM is limited to 50mA.
Option [5] OFF = PGM is Normally Open (default).
Option [5] ON = PGM is Normally Closed.
5.2 PGM Activation Event
SECTION [014] to [017]
Modules belonging to the DGP2 series are programmed using the
PGM Programming table in the Digiplex/DigiplexNE Modules’
Programming Guide. The PGM Activation Event determines which
event will activate the keypad's on-board PGM output. The EVENT
GROUP specifies the event, the FEATURE GROUP identifies the source,
and the START # and END # sets the range within the Feature Group.
Use the PGM Programming Table in the Digiplex/DigiplexNE
Modules’ Programming Guide to program the keypad’s PGM
deactivation Event.
Enter the sections that correspond to the EVENT GROUP, FEATURE
GROUP, START # and END # of the PGM and enter the required data.
Event group Feature group Start # End #
PGM [014] [015] [016] [017]
DGP2648_EI06.fm Page 11 Thursday, July 22, 2004 9:15 AM

12 Reference & Installation Manual
5.3 PGM Deactivation Event
SECTION [018] to [021]
Modules belonging to the DGP2 series are programmed using the
PGM Programming table in the Digiplex/DigiplexNE Modules’
Programming Guide. If the PGM Deactivation Option is set to follow
the PGM Deactivation Event, the PGM will return to its normal state
when the event programmed in sections [018] to [021] occurs. The
EVENT GROUP specifies the event, the FEATURE GROUP identifies the
source and the START # and END # sets the range within the Feature
Group. Use the PGM Programming Table in the Digiplex/DigiplexNE
Modules’ Programming Guide to program the keypad’s PGM
Deactivation Event.
Enter the sections that correspond to the EVENT GROUP, FEATURE
GROUP, START # and END # of the PGM and enter the required data.
5.4 PGM Deactivation Mode
SECTION [011] Option [2]
If option [2] is enabled, the keypad's on-board PGM will be
deactivated according to the PGM Timer (PGM Timer on page 13)
instead of the PGM Deactivation Event.
Option [2] OFF = Deactivation as per PGM Deactivation Event (default).
Option [2] ON = PGM will deactivate according to the PGM Timer.
Event group Feature group Start # End #
PGM [018] [019] [020] [021]
DGP2648_EI06.fm Page 12 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 13n
5.5 PGM Base Time
SECTION [011] Option [3]
This option defines whether the value programmed in section [013] is
in minutes or seconds.
Option [3] OFF = PGM Base Time is 1 second (default).
Option [3] ON = PGM Base Time is 1 minute.
5.6 PGM Timer
SECTION [013]
If the PGM Deactivation Mode is set to follow the PGM timer, the
value programmed in section [013] represents how long the PGM will
remain in its opposite state (see “PGM State” on page 11) after being
activated. To program the timer, enter a 3-digit decimal value (001 to
255) in section [013]. The 3-digit value will be multiplied by the PGM
Base Time of 1 second or 1 minute (see section 5.5).
5.7 PGM Test
SECTION [030]
Use this section to initiate a PGM test, which will activate the PGM
for 8 seconds. Enter section [030] to activate this test.
DGP2648_EI06.fm Page 13 Thursday, July 22, 2004 9:15 AM

14 Reference & Installation Manual
6.0 List of Sections
Do not assign the same display number to more than one
section. A maximum of 4 partitions can be assigned to the
keypad.
Section Description Data Default
[001] PARTITION 1 DISPLAYED ON __/__/__ 001 = (LED A1)
[002] PARTITION 2 DISPLAYED ON __/__/__ 002 = (LED A2)
[003] PARTITION 3 DISPLAYED ON __/__/__ 003 = (LED A3)
[004] PARTITION 4 DISPLAYED ON __/__/__ 004 = (LED A4)
[005] PARTITION 5 DISPLAYED ON __/__/__ 000
[006] PARTITION 6 DISPLAYED ON __/__/__ 000
[007] PARTITION 7 DISPLAYED ON __/__/__ 000
[008] PARTITION 8 DISPLAYED ON __/__/__ 000
000 = DISABLED OR NOT DISPLAYED
001 = LED A1
002 = LED A2
003 = LED A3
004 = LED A4
DGP2648_EI06.fm Page 14 Thursday, July 22, 2004 9:15 AM

Digiplex LED Keypad 15n
U= Default
SECTION [009]: Keypad Options
Option Description OFF ON
[1] CONFIDENTIAL MODE UDISABLED .ENABLED
[2] EXIT CONFIDENTIAL
MODE UPRESS KEY .ENTER CODE
[3] MUTING UDISABLED .ENABLED
[4] BEEP ON EXIT DELAY .DISABLED UENABLED
[5] CHIME ON ZONE
CLOSURE
UDISABLED .ENABLED
[6] TO [8] N/A
Section [010]: Beep on Trouble
Option Description OFF ON
[1] BEEP ON SYSTEM
TROUBLES / CLOCK LOSS
UDISABLED .ENABLED
[2] BEEP ON COMMUNICATOR
TROUBLES
UDISABLED .ENABLED
[3] BEEP ON MODULE / BUS
TROUBLES
UDISABLED .ENABLED
[4] BEEP ON ZONE TROUBLES UDISABLED .ENABLED
[5] TO [8] N/A
DGP2648_EI06.fm Page 15 Thursday, July 22, 2004 9:15 AM

16 Reference & Installation Manual
U= Default
Section [011]: Keypad Tamper Enable
Option Description OFF ON
[1] PGM STATE UN.O. .N.C.
[2] PGM DEACTIVATION
MODE
UDEACTIVATION
EVENT
.PGM TIMER
[3] PGM BASE TIME U1 SECOND .1 MINUTE
[4] N/A
[5] KEYPAD ANTI-TAMPER UDISABLED .ENABLED
[6] TO [8] N/A
Section Data Description Default
[012] __/__/__ (005-255) CONFIDENTIAL MODE
TIMER 120 SEC.
Section Data Description Default
[013] __/__/__ (001-255) PGM TIMER 005
DGP2648_EI06.fm Page 16 Thursday, July 22, 2004 9:15 AM