Paradox DigiplexNE DGP2-641 User manual

LCD Keypad V1.1
DGP2-641
Reference and Installation Manual

Table Of Contents
Introduction..................................................... 3
Specifications ...................................................... 3
Installation ....................................... ................ 4
Connecting Keypad Zones.................................. 4
Programmable Output......................................... 5
Programming .................................................. 6
Entering Module Programming Mode.................. 6
Programming Methods ........................................ 7
Feat ure Select Programming ...... .. .. .. ...... .. .. .. ...... .. .. 7
Dec imal Program ming .. .. .. .. ...... .. .. .. ...... .. .. .. ...... .. .. .. 7
Module Broadcast ............................................... 7
Memory Key ........................................................ 8
Download Contents of Memory Key to Keypad... 8
Copy the Keypad Contents to the Memory Key .. 9
System Options ............................................ 11
Partition Assignment ......................................... 11
Display Access Code Entry............................... 11
Display Exit Delay Timer ................................... 11
Display Entry Delay Timer ................................. 12
Confidential Mode ............................................. 12

Confidential Mode Timer ................................... 13
Time Display Option .......................................... 14
Muting................................................................ 14
Beep on Exit Delay ............................................ 14
Chime on Zone Closure..................................... 15
Beep on Trouble ................................................ 15
Keypad Tamper Enable..................................... 16
Communication Bus Voltmeter .......................... 16
Programmable Output Options ................... 18
PGM State ......................................................... 18
PGM Deactivation Mode.................................... 18
PGM Base Time ................................................ 19
PGM Override .................................................... 19
PGM Timer ........................................................ 19
PGM Activation Event........................................ 20
PGM Deactivation Event ................................... 20
Message Programming ................................ 22
Special Function Keys ....................................... 23

Digiplex/DigiplexNE LCD Keypad 3n
1.0 Introduction
Thank you for choosing Paradox Security Systems. Digiplex/
DigiplexNE Security Systems are advanced technology security
systems that will provide reliable security protection and powerful
features that are easy to use. The elegant and user-friendly LCD
Keypad will allow easy access to the security system's functions
and information at the touch of a button. Since all programming
is accomplished through the keypad, please read this manual
carefully.
1.1 S pe cific ations
Power input: 12 to 16 Vdc, 80mA maximum
PGM current limit: 50 mA
Numberof inputs: 1
Po we r in di ca ti on: Ye llo w LE D on
Locate indica tion: Green a nd ye ll ow LE Ds fl ash si mul tane ousl y
Bu s fau lt i nd ication : Red an d ye ll o w LED s f la sh al ter n ate ly
An ti-ta mp er sw itch: Ye s ( also used to de act iva te lo cat e)
LCD: Super Twisted Nematic display (STN), wide
viewing ang le, 2 line s of 1 6 char a cter s, b ackl igh t
an d co ntr a st ad j usta bl e
Compatibility: Any Digiplex/DigiplexNE Control Panel

4 Reference & Installation Manual
2.0 Installation
The LCD keypad (DG2P-641) is connected to the control panel's
communication bus in a star and/or daisy chain configuration.
The 4-wire communication bus provides power and two-way
communication between the control panel and all modules
connected to it. Connect the four terminals labeled red, black,
green and yellow of each keypad to the corresponding terminals
on the control panel (refer to Figure 2.1 on page 5). Refer to the
Digiplex or DigiplexN E Reference & Installation Manual f or the
maximum allowable installation distance from the control panel.
2.1 Connecting Keypad Zones
Each keypad has one traditional hardwired input terminal,
allowing you to connect one detector or door contact directly to
the keypad. For example, a door contact located at the entry
point of an establishment can be wired directly to the input
terminal of the entry point keypad instead of wiring the door
contact all the way to the control panel.
Connect the device to the keypad's input terminal as shown in
Figure 2.1 on page 5. In order to communicate its status to the
control panel, devices connected to the keypad's input terminal
must be assigned to a zone in the control panel and the zone's
parameters must be defined. For more information on zone
assignment, please refer to the Digiplex or Digiplex NE
Reference & Installation Manual. Please note that even with the
ATZ (zone doubling) feature enabled, the keypad supports only
one detection device.

Digiplex/DigiplexNE LCD Keypad 5n
2.2 Programmable Output
Each keypad has one on-board PGM. A PGM is a programmable
output that toggles to its opposite state (i.e. a normally open
PGM will close) when a specific event has occurred in the
system (refer to sect ion 5.0 on page 17). Upon act iv ation, the
PGM can provide 50mA to any device connected to it. If the
current drawn is to exceed the current limit, a relay should be
connected to the PGM as shown in Figure 2.1.
Figure 2.1: Connecting the Keypad and Keypad Zone

6 Reference & Installation Manual
3.0 Programming
To program the DGP2-641 keypad, enter Module Programming
Mode and then enter the desired section followed by the required
data. When programming the keypad, use the keypad’s
programming sheets (found in the Digiplex/DigiplexNE Modules’
Programming Guide) to keep track of which sections were
programmed and how. We strongly recommend you read this
entire manual before you begin programming.
The LCD keypad can also be programmed using the WinL oad
Security System Management Software. For more information,
refer to the WinLoad instructions or visit our Web site at
www.paradox.ca.
3.1 Entering Module Programming Mode
The keypad, like all other modules in the system , is programmed
through the control panel. To do so, you must first enter Module
Programming Mode:
1. Fr o m No r ma l Mo de pr e ss an d h o l d th e [0] key.
2. E nt er th e [INSTALLER CODE](by default 000000).
3. Enter section [953] (DGP-48) / [4003] (DGP-NE96).
4. E nt er th e ke yp ad ’ s 8 - d igi t [SERIAL NUMBER].
5. Enter the 3-digit [SECTION] you want to program.
6. Enter the required [DATA].
The control panel will then redirect all programming to the
selec ted keypad. Ev ery time t he [CL EA R ]key is pressed it will
revert to the preceding step, unless entering in data in which

Digiplex/DigiplexNE LCD Keypad 7n
case it will erase the current data entry. Please note that the
se r ia l n u m b er is l o ca te d o n th e ke yp ad ' s P C bo a r d or en te r
section [000] in Step 3 to view the keypad’s serial number.
3.2 Programming Methods
The following methods can be used when programming the
keypad:
3.2.1 Feature Select Programming
Some sections are programmed by enabling or disabling
options. Within the sections, numbers from[1] to [8 ]
represent a specific keypad option. Press the key
corresponding to the desired option and the digit will
appear in the display. This means the option is enabled.
Press the key again to remove the digit from the display
thereby disabling the option. Press [ENTER]when options
are set.
3.2.2 Decimal Programming
Some sections require that a decimal value be entered. In
this method, any digit from 000 to 255 can be entered.
3.3 Module Broadcast
The control panel’s Module Broadcast feature can be used to
copy the contents of one keypad to one or more keypads.
1. From Normal Mode press and hold the [0] key.
2. E nt er [INSTALLE R CODE](default: 000000).
3. Enter section [954] (DGP-48) / [4004] (DGP-NE96).
4. E nt er th e [SERIAL #] of the source keypad. The sourceis
the programmed keypad whose data you want to copy to

8 Reference & Installation Manual
other keypads.
5. E nt er th e [SERIAL #] of the destination keypads. The
des tination is the keypad(s)you want toprogram with the
source’s data. If you want to program more than one
keypad with the source’s data, enter the serial numbers
of the keypads one at a time.
6. O nc e yo u ha ve e n te re d th e se rial nu mb er s o f t he
keypads you want to program, press the [ACC] key.
3.4 Memory Key
SECTIONS [510] AN D [520]
Download information to and from an LCD keypad using the
memory key (PMC-3).
Only the PMC-3 memory key will function with the
LCD keypad.
3.5 Download Contents of Memory Key to Keypad
SECTION [510]
1. Insert the memory key into the keypad’s c onnec tor
labelled “KE Y” (refer to Figure 2.1 on page 5).
2. To download the contents of the memory key, enter the
Section [510] = Download all from the memory key (LCD
keypad s ec tions [001] to [396] and all
messages) to the LCD keypad.
Section [520] = Copy the LCD keypad sections [0 01] to [396]
and all messages to the memory key.