Paradox NV35M User manual

PARADOX.COM
Installation Manual v1.0
Outdoor/Indoor
Window and Sliding Door
Dual Detector with
Anti-Masking and
Pet Immunity
NV35M-EI01
General Description
Thank you for choosing the NV35M for your professional protection needs.
The NV35M wired version will provide you the most advanced window and
sliding door protection either in Pet Immune or Sharp mode. If you have
any comments please write to us at Paradox.Com/products/feedback.
This guide describes how to install and program the NV35M.
Installing the NV35M
1. Remove the NV35M front cover - open the Captive screw.
2. Remove the Main Unit: open the two snap-lock mechanisms on each
side of the back cover attaching the Main Unit to the back cover as
displayed below. Then remove the Main Unit.
Figure 3 – Removing the Main Unit
3. Pull the wires from the control panel through the knockout holes and
mount the back cover onto the window frame or wall using screws.
Figure 4 – Mounting the Back Cover
4. Attach the Main Unit to the back cover - ensure the locks snap closed.
Figure 5 – Attaching the Main Unit
5. Connect the wires to the terminal blocks according to the following
wiring assignment.
Table 1: Wiring Assignment
6. Set the following Detector settings according to requirements.
Figure 6 – Detector Settings
The following table displays the Dip Switch settings.
Table 2: Dip Switch Settings
7. Replace the front cover and close the Captive screw.
Warning: Do not obscure the detector's field of view.
Figure 1 – Removing the
Front Cover
Figure 2 – Main Unit
Front cover
Captive screw
Knockout
holes
Mounting
screw 1
Mounting
Tamper
screw 2
Tamper
knockout
hole
Terminal Connector Recommended Wiring Assignment
1 12V+
2 Minus (-)
3 Fault indication
4 Tamper indication
5 Common (Fault & Tamper)
6 Alarm indication
7 Common (Alarm)
Dip Switch
Number Function Mode Description
1 LED ON: LED on (default)
OFF: LED off
2PET Immunity/
SHARP Mode
ON: PET Immunity mode (default)
OFF: SHARP mode
123
Dip Switch
Sensitivity Trimmer
LED flashes green 1-3 times
according to the selected
level
NV35M
All manuals and user guides at all-guides.com
all-guides.com

PARADOX.COM
Testing the NV35M
Perform a Walk-Test to test successful installation: Walk slowly across the
far end of the detection range. Ensure detection.
Walk test mode lasts 5 minutes after the tamper screw is closed.
Beam Pattern
PET Mode
SHARP Mode
Top View
LED Display
Technical Specifications
Notification
Changes or modifications to this equipment not expressly approved by the
party responsible for compliance (Paradox Security Systems Ltd.) could
void the user’s authority to operate the equipment.
Warranty
The Limited Warranty Statement found on the website www.paradox.com/
terms.
Your use of the Paradox product signifies your acceptance of these terms
and conditions.
Patents
The following US patents may apply 5,886,632 and 6,215,399, Other
Canadian and international patents may apply.
Printed in Canada 05/2015.
Feature LED Status Indicator
Tamper open Green: ON for 0.3 seconds every 30
seconds
PIR sensitivity level setting Green: Flashes 1-3 times according to
the selected level
Alarm detection Red: ON for 2 seconds
Booting/Tamper close Green/Red alternating flashes for 30
seconds
Anti-mask detection Orange: Flashes ON/OFF 3 times every
60 seconds
Specification Description
Infrared sensor type 2 Dual elements
Detection range • PET Immunity mode: 7.5m x 2m (25 x 7
ft)
• Sharp mode: 10 x 2m (33 x 7 ft)
Super Pet Immunity Pet size approximately 50cm
Anti- mask Active IR detection for blocking items 30cm
and sprayed liquid
Input voltage 10 to 15VDC
Current consumption Typical: 15mA
Maximum: 19.2mA
Compatibility EVO, Spectra and Magellan systems
Outdoor protection IP54
Operation temperature -35°c: +50°c
Relative humidity 95% non-condensing
Dimensions 12.3 x 6.1 x 4.3 cm (4.8 x 2.4 x 1.7 in.)
Certifications CE, EN50131-2-2 Grade 3, Class IV
Weight 100g / 0.2 lb
All manuals and user guides at all-guides.com