Paradox 1686V User manual

User Quick Reference Guide (1686V & 1686H)
KEYPAD OVERVIEW
1686V LED Keypad
REGULAR:Arms entire partition when all
zones are closed.
Enter your [ACCESS CODE]* (or press and
hold the [ENTER]†key for 3 seconds).
FORCE:Arms entire partition without waiting
for all zones to close.
Press the [FORCE]key, and then enter your
[ACCESS CODE]* (or press and hold the
[FORCE]†key for 3 seconds).
S TAY : Arms partition’s perimeter only, which
allows you to remain in the protected area.
Press the [STAY]key, and then enter your
[ACCESS CODE]* (or press and hold the
[STAY]†key for 3 seconds).
INSTANT:Stay arms partition, but an alarm
will occur instantly if a zone opens, including
entry delay zones.
After Stay arming, press and hold the
[STAY]†key for 3 seconds.
*If keys [1] and [2] flash, you must specify which partition you wish to arm or disarm by pressing the
corresponding key.
†Must be enabled by your installer.
HOW TO ARM AND DISARM
Disarming
Enter your [ACCESS CODE]*.
AC LIGHT
On = AC power on
Off = Power failure
READY LIGHT
On = All zones are closed
Off = Zone(s) open or armed
Flash = Exit Delay indicates
that the system will become
armed soon
ARM LIGHTS
On = Partition armed
Off = Partition disarmed
Flash = Partition Stay armed
Fast Flash = Partition in
alarm
Press and hold the [PG]key for 3
seconds to activate:
__________________________
(i.e. garage door, smoke reset, etc.)
Made a mistake?
Press the [CLEAR]key to re-enter
data, exit the current mode or
cancel an action.
A numeric key illuminates if its
corresponding zone is open.
Partition 1 Partition 2
1686EQ02.fm Page 1 Friday, March 21, 2003 10:48 AM

Press and hold one of the key combinations
listed below for 2 seconds to activate a
panic alarm.
When the [MEM]key is illuminated, an alarm
has occurred within your system. Press the
[MEM]key to view the breached zone(s).
The breached zone’s corresponding key will
be illuminated.
When the [TBL]key is illuminated, press it to view the Trouble Display ([TBL]key flashes).
Each key that is illuminated represents a separate trouble condition as shown below:
When the [BYP]key is illuminated, there are
bypassed zones currently in your system.
Method 1:
1. Press the [BYP]key.
2. Enter your [ACCESS CODE].
3. Press the keys corresponding to the
zones you wish to bypass, or press
[BYP]to recall the previously
bypassed zones.
4. Press [ENTER].
Method 2:
1. Press and hold the [BYP]†key for 3
seconds.
2. Go to step 3 in method 1.
Press and hold the numeric key
corresponding to the zone for 3 seconds to
enable or disable chiming for that zone*.
Press and hold the [CLEAR]key for 3
seconds to enable or disable keypad
muting*.
*A confirmation beep (BEEP-BEEP-BEEP-BEEP-
BEEP) signifies that the feature has been enabled,
and a rejection beep (BEEEEEEEEEEEEEP) sounds
when the feature is disabled.
PANIC ALARMS†
Panic Alarm
Type Key Combinations
Police
Medical
Fire
Press and hold [1] & [3]
Press and hold [4] & [6]
Press and hold [7] & [9]
ALARM MEMORY DISPLAY
TROUBLE DISPLAY
[1] Low/No battery [8] Clock loss (press [8] to reprogram HH:MM)
[2] Wireless transmitter low
battery
[9] Tamper/Zone wiring failure (press [9] to
view the zone)
[3] Power failure [10] Telephone line monitoring failure
[4] Bell/PGM2 disconnected [STAY]Fire zone trouble
[5] Bell current failure [BYP]Module loss
[6] Auxiliary current failure [MEM]Wireless transmitter supervision loss
[7] Communication failure [FORCE]Keypad fault
BYPASS PROGRAMMING CHIME PROGRAMMING
†Must be enabled by your installer.
© 2003 Paradox Security Systems. Spectra is a registered trademark of Paradox Security Systems.
1686EQ02.fm Page 2 Friday, March 21, 2003 10:48 AM