Paradox Digiplex EVO DGP2-640 User manual

Icon LCD Keypad
V1.0
Reference & Installation Manual
DGP2-640
DGP-641
DGP2640_EI00.fm Page -3 Thursday, April 7, 2005 12:05 PM

DGP2640_EI00.fm Page -2 Thursday, April 7, 2005 12:05 PM

Table of Contents
Introduction...................................................................1
Specifications........................................................................ 1
Installation.....................................................................2
Connecting the Keypad......................................................... 2
Connecting the Keypad Zone................................................ 2
Programmable Output........................................................... 3
Programming ................................................................4
Entering Module Programming Mode ................................... 4
Programming Methods.......................................................... 5
Module Broadcast................................................................. 5
System Options ............................................................7
Partition Display)................................................................... 7
Confidential Mode................................................................. 8
Exit Confidential Mode.......................................................... 8
Muting ................................................................................... 8
Beep on Exit Delay................................................................ 9
Chime on Zone Closure ........................................................ 9
Time Format.......................................................................... 9
Beep on Trouble.................................................................... 9
Keypad Anti-Tamper Enable............................................... 10
Confidential Mode Timer..................................................... 11
Programmable Output Options .................................11
PGM State........................................................................... 11
PGM Deactivation Mode ..................................................... 11
PGM Base Time.................................................................. 12
PGM Timer.......................................................................... 12
DGP2640_EI00.fm Page -1 Thursday, April 7, 2005 12:05 PM

PGM Activation................................................................... 12
PGM Deactivation............................................................... 13
PGM Test............................................................................ 13
List of Sections .......................................................... 14
DGP2640_EI00.fm Page 0 Thursday, April 7, 2005 12:05 PM

DGP2-640 Icon LCD Keypad 1
1.0 Introduction
Thank you for choosing Paradox Security Systems. Our advanced
technology security systems provide you with reliable security
protection and powerful features which are easy to use. The
DGP2-640 Icon LCD keypad provides easy access to the security
system’s functions and status at a glance.
1.1 Specifications
Power input: 12-16 Vdc, 80mA maximum
PGM current limit: 50mA
Number of inputs: 1
Number of zones: 1 standard zone, no tamper recognition
Locate deactivation: Anti-tamper switch
Compatibility: Any Digiplex control panel
Table 1: LED Functionalities
LED Function Display Status
AC Light ON
OFF Power On Power Off
Status Light Green ON All zones closed
Green OFF Zone(s) open
Green flash Exit delay
Red ON Area(s) armed
Red OFF Area(s) disarmed
Red flash System in alarm
Green and yellow
flash simultaneously Locate indication
Red and yellow
flash alternately Combus fault
DGP2640_EI00.fm Page 1 Thursday, April 7, 2005 12:05 PM

2 Reference & Installation Manual
2.0 Installation
2.1 Connecting the Keypad
The DGP2-640 is connected to the control panel’s combus in a star
and/or daisy chain configuration. The four-wire combus provides
power and two-way communication between the control panel and all
modules connected to it. Connect the four terminals labeled +, -, GRN
and YEL on the keypad to the corresponding terminals on the control
panel as shown in Figure 1 on page 3. Refer to the control panel’s
Reference & Installation Manual for the maximum allowable
installation distance from the control panel.
2.2 Connecting the Keypad Zone
Your keypad has one hardwired input terminal, allowing you to
connect one detector or door contact directly to it. For example, you
can wire a door contact located at the entry point of an establishment
directly to the input terminal of the entry point keypad, instead of
wiring the door contact all the way to the control panel.
Connect the device to the keypad's input terminal as shown in Figure
1 on page 3.
The keypad zone follows the control panel’s EOL definition.
In order to communicate its status to the control panel, the keypad's
input must be assigned to a zone in the control panel and the zone's
parameters must be defined.
The control panel does not recognize tampers originating
from the keypad zone.
For more information on zone assignment, please refer to your
control panel's Reference & Installation Manual. Please note that
even with the ATZ (zone doubling) feature enabled, the keypad
DGP2640_EI00.fm Page 2 Thursday, April 7, 2005 12:05 PM

DGP2-640 Icon LCD Keypad 3
supports only one detection device.
2.3 Programmable Output
Each keypad has one on-board PGM. A PGM is a programmable
output that switches to its opposite state (i.e. a normally open PGM
will close) when a specific event has occurred in the system (see
Programmable Output Options on page 11). Upon activation, the
PGM can provide 50mA to any device connected to it. If the current
drawn is to exceed the current limit, a relay should be connected to
the PGM as shown in Figure 1.
Figure 1: Connecting Keypads and Keypad Zones
A keypad’s input must be assigned
to a zone, keyswitch or virtual input
in the control panel. In addition, the
zone’s parameters must be
defined. For detailed instructions
please refer to the control panel’s
Reference and Installation Manual.
*The keypad zone follows the control
panel’s EOL definition. The zone speed is
set at 600mS and cannot be changed.
Note: The keypad’s anti-tamper switch
will communicate its status to the control
panel via the combus.
To other
keypads
and/or
modules.
DGP2640_EI00.fm Page 3 Thursday, April 7, 2005 12:05 PM

4 Reference & Installation Manual
3.0 Programming
To program the DGP2-640 keypad, enter Module Programming
Mode and then enter the desired section followed by the required
data. When programming the keypad, use the keypad’s
programming sheets (found in the Digiplex Modules’ Programming
Guide; also, refer to List of Sections on page 14) to keep track of
which sections were programmed and how. We strongly recommend
you read this entire manual before you begin programming.
The Icon keypad can also be programmed using the WinLoad
Installer Upload/Download Software. You can program control panels
and keypads remotely through a modem at 300 baud or on-site at
19.2k/38.4k baud with a 306 Adapter. For more information, refer to
the WinLoad instructions or visit our website at www.paradox.ca.
3.1 Entering Module Programming Mode
The keypad, like all other modules in the system, is programmed
through the control panel. To do so, you must first enter Module
Programming Mode:
1. From Normal Mode press and hold the [0] key.
2. Enter the [INSTALLER CODE](by default 000000).
3. Enter section [953] (DGP-848) / [4003] (DGP-NE96).
4. Enter the keypad’s 8-digit [SERIAL NUMBER].
5. Enter the 3-digit [SECTION] you want to program.
6. Enter the required [DATA].
The control panel will then redirect all programming to the selected
keypad. Every time the key is pressed it will revert to the
preceding step—unless entering in data, in which case it will erase
the current data entry. Please note that the serial number is located
on the keypad's PC board or enter section [000] (DGP-848) or
DGP2640_EI00.fm Page 4 Thursday, April 7, 2005 12:05 PM

DGP2-640 Icon LCD Keypad 5
[0000] (DGP-NE96) in Step 3 to view the keypad’s serial number.
When entering the serial number, the Sand Ticons on the right
side of the screen will illuminate and you can use the [S] and [T]
keys to scroll through the serial number.
3.2 Programming Methods
The following methods can be used when programming the keypad:
3.2.1 Feature Select Programming
Some sections are programmed by enabling or disabling
options. Within the sections, numbers from [1] to [8] represent
a specific keypad option. Press the key corresponding to the
desired option and the digit will appear in the display. This
means the option is enabled. Press the key again to remove
the digit from the display thereby disabling the option. Press
the key when options are set.
3.2.2 Decimal Programming
Some sections require that a decimal value be entered. In this
method, any digit from 000 to 255 can be entered.
3.3 Module Broadcast
The control panel’s Module Broadcast feature can be used to copy
the contents of one keypad to one or more keypads.
1. From Normal Mode press and hold the [0] key.
2. Enter the [INSTALLER CODE](default: 000000).
3. Enter section [954] (DGP-848) / [4004] (DGP-NE96).
4. Enter the [SERIAL #] of the source keypad. The source is the
programmed keypad whose data you want to copy to other
keypads. When entering the serial number, the Sand Ticons
on the right side of the screen will illuminate and you can use
the [S] and [T] keys to scroll through the serial number.
5. Enter the [SERIAL #] of the destination keypad(s). The
DGP2640_EI00.fm Page 5 Thursday, April 7, 2005 12:05 PM

6 Reference & Installation Manual
destination is the keypad(s) you want to program with the
source’s data. If you want to program more than one keypad
with the source’s data, enter the serial numbers of the keypads
one at a time.
6. Once you have entered the serial numbers of the keypad(s)
you want to program, press the key.
For more information, please see the control panel’s Programming
Guide.
DGP2640_EI00.fm Page 6 Thursday, April 7, 2005 12:05 PM