Paradox ESPRIT 728 ULT Operating instructions

1
ESPRIT 728 ULT QuickProgramming Guide
V2.10
To enter Programming Mode:
1. Press [ENTER]
2. Enter [2828]or [282828] (Enter key flashing), you are in the programming mode
3. Enter 3 digits ADDRESS number
4. Enter required DATA (Either enter 2 digits, 3 digits or ON / OFF relevant key)
Press [ENTER] to confirm or [CLEAR] to ignore
A=10, B=11/STAY, C=12/AWAY, D=BYP, E=MEM & F=TBL
Remember: After keyed in a required DATA, always press ENTER and then CLEAR, in order to let the
ENTER key flashing before proceed with entering the next 3 digits ADDRESS number.
Step 1: To program zone type
Press [ENTER] [2828] or [282828], you are in the programming mode, ENTER key is flashing
 ON relevant key [1 to 10] for ZONE features wanted
[key in 100][On key wants to be 24 HOUR zone]
[key in 104][ON key wants to be INSTANT zone]
[key in 108][ON key wants to be FOLLOW zone]
Note: Zones that are not selected in [100] to [108] automatically become delay zone.
[key in 096][ON key wants to be SILENT zone]
[key in 116][ON key wants to be STAY zone]
[key in 124][ON all zone to allow for bypass]
Example:
[key in 104], [ON key 2,3,4], meaning zone 2,3 & 4 are instant zone. Zone 1 is delay zone.
[key in 124], [ON 1,2,3, & 4], all zones are bypassable zone
Example:
[key in 116], [ON key 1, 3 & 4], meaning zone 1,3 & 4 are to be protected in stay arming, zone 2 is
bypassed.
Example:
[key in 100], [ON 3], meaning this zone 3 is a fire zone (24 hours zone)
Note: If zone 3 is enable as 24 hours zone, it is a FIRE zone
Example:
[key in 100][ON key 4], meaning zone 4 is 24 hours zone
[key in 096][ON key 4], meaning zone 4 is a silent zone (for panic button)
 ON relevant key [1 to 10] for USER features wanted
[key in 062][ON key 1 to 10], to allows user 1 to 10 in stay arming
[key in 068][ON key 1 to 10], to allows user 1 to 10 in away/ force arming
[key in 074][ON key 1 to 10], to allows user 1 to 10 to bypass zones
Note: By default, master code (as user 00) allows to force and stay arming.

2
Step 2: To program features
Press [ENTER] [2828] or [282828] , you are in the programming mode, ENTER key is flashing
[key in 088], [ON key 1,2,3,4,5,6,7,8, 9 &12] & [OFF key MEM]
[key in 090], [ON key 11 or/and 12], for keypad zone
[key in 049], [enter 060], for exit delay 60 seconds
[key in 050], [enter 060], for entry delay 60 seconds
[key in 053], [enter 003], for zone speed 45 ms. (for vibration sensor). 004 for 60 ms, 005 for 75 ms.
* Choose either Step 3A or 3B
Step 3A: To call CMS
Press [ENTER] [2828] or [282828], you are in the programming mode, ENTER key is flashing
[key in 038][press 10 then 10], contact ID format
[key in 086][ON key 7 & 12][ENTER][CLEAR], to call CMS phone.
[key in 090][ON key 10][ENTER][CLEAR], to enable Duress signal.
[key in 046][enter 001], for daily test
[key in 047][enter HHH], for hour
[key in 048][enter HHH], for minutes
Press [ENTER] [2828] or [282828] ,then [7], you are in the streamline programming mode, ENTER key
and 2ND are flashing.
[key in 04][enter phone number 1][ENTER][CLEAR], CMS phone number 1
[key in 06][enter phone number 2][ENTER][CLEAR], CMS phone number 2
[key in 08][enter 8888 8888][ENTER][CLEAR], account number
Note: to clear phone number, replace digit with [2ND]
Step 3B: To call Handphone
Press [ENTER] [2828] or [282828], youare in the programming mode, ENTER key is flashing
[key in 037][enter 7 then 2ND], waits for 15 rings call duration
[key in 038][enter TRBL then TRBL], pager format
[key in 086][ON key 7, 11 & 12][ENTER][CLEAR], to call phone 1 and phone 2 each ONE time
Note: if only [ON key 7 & 12, OFF key 11][ENTER][CLEAR], to call ONLY phone 1 one time
[key in 090][ON key MEM],
Press [ENTER] [2828] or [282828] ,then [7], you are in the streamline programming mode, ENTER key
and 2ND are flashing.
[key in 36][enter 33333333], to report zone 1 to 4
[key in 37][enter 33333333], to report zone 5 to 8 (program only if these zones are used)
[key in 38][enter 3333], to report zone 9 to 10
[key in 64][enter 2ND 2ND 333333][ENTER][CLEAR], to report panics
[key in 04][enter phone number 1][ENTER][CLEAR], handphone number 1
[key in 06][enter phone number 2][ENTER][CLEAR], handphone number 2
[key in 08][enter 8888 8888], account number

3
Others
Press [ENTER] [2828] or [282828], you are in the programming mode, ENTER key is flashing
1. Keypad setting
[key in 090][ON key 11][ENTER][CLEAR], for keypad zone 1
[key in 090][ON key 12][ENTER][CLEAR], for keypad zone 2
Select the jumper at the keypad, J1 OFF is keypad 1 and J1 ON is keypad 2.
Power down and on again after changing the jumper setting.
2. Keyswitch
[key in 086][ON key 3][ENTER][CLEAR], to enable keyswitch
Connect a 500 ohm resistor in series with AUX of keypad black wire & another wire connect to GRN of
keypad green wire.
500 ohm
resistor
3. Partitioning
[key in 086][ON key 8][ENTER][CLEAR], to enable partitioning
 ON relevant key [1 to 10] for ZONE to be at partition A or B
[key in 116], for zone Partition A
[key in 120], for zone Partition B
 ON relevant key [1 to 10] for USER to use in Partition A or B
[key in 062], to allows user 1 to 10 in Partition A
[key in 068], to allows user 1 to 10 in Partition B
Note: Once the system in Partition, Stay and Away/Force features are not available.
AUX AUX
+
-
GRN YEL
COM NO
keyswitch

4
4. Doubling method
Z3
Z1 Z2 Z4
728: [1/2] [3/4] [5/6] [7/8]
Zone 1,3,5 & 7 use 1K resistor, zone 2,4,6 & 8 use 2.2K resistor.
Keypad 1 as zone 9 and keypad 2 as zone10, need to put 1K resistor for keypad zones.
[key in 090][ON key 8][ENTER], to enable zone doubling
[key in 088], [ON key MEM][ENTER], disable EOL.
AND program zone type in Step 1.
Important note: Once the panel is in zone doubling, ALL zones are Normally Closed (NC).
Note: For zone doubling, the zone speed setting in address [053] should be [004] and above to avoid false
alarm caused by vibration sensors.
For Fire zone connections using 4-wire smoke detector
Once zone 3 is enable as FIRE zone in this zone doubling method:
[key in 090][ON key 1][ENTER], to disable zone 4.
[key in 100][ON key 3][ENTER], to program zone 3 as fire zone.
[key in 039], press [5][0], PGM to reset smoke detector
[key in 040], press [5][0], PGM to reset smoke detector
[key in 042], press [2ND][6], PGM to reset smoke detector
[key in 056], press [0][0][4], PGM to reset smoke detector
Note: Once zone 3 is a FIRE zone, zone 4 can not be used. Now, this zone 3 is a parallel wiring..
1 K
2.2
K1K
2.2
K
1 C 2 3 C

5
Z1 Z2 Z3 Z5 Z6
-
+
Note: The purpose of Relay is to reset smoke power. By pressing [CLEAR] and [ENTER] key together for
3 seconds.
For Fire zone connections using 2-wire smoke detector
Z1
Z2 Z3 Z4
Note: Maximum up to 5 pcs 2-wire smoke detector.
1 K
2.2
K
1 C 2 3 C
2-wire
Smoke
detector
(NO)
PGM AUX AUX
+
-
1 K
2.2
K
1 K
2.2
K
1K
1 C 2 3 C
COM NO
Smoke
detector
PGM AUX AUX
+
-
Relay:12vDC
NO
COM
NC
-
+
1 K
2.2
K
2-wire
Smoke
detector
(NO)
1
k

6
728: [1/2] [3/4] [5] [7/8]
[key in 086][ON key BYP][ENTER], to enable zone 2-wire smoke detector to input 3 (as zone 5 in zone
doubling)
5. Utility
 Walk test
Press [ENTER] [2828] or [282828], you are in the programming mode, ENTER key is flashing
Press [ENTER][2828][8][CLEAR], to activate walk test mode.
Press [ENTER][2828][8][CLEAR], to de-activate walk test mode.
 To reset panel back to factory default
1. Remove the battery and switch OFF AC power.
2. Short the PGM and zone 1 terminal (labeled as 1) with a wire.
3. Power ON AC and connect the battery.
4. Wait for 10 seconds then remove the wire.

7
User functions
Normal function:
Type Action Display on 636 keypad
Arming / Disarm [Enter 4 digit user code] ARM is ON
Stay arming
(Stay zone will be bypassed) [STAY][4 digit user code] ARM & STAY are ON
Force arming
(Zone opened will be
bypassed, it consider arm
when it closed back)
[FORCE][4 digit user code] ARM is ON
Instant arming
(Delay zone becomes Instant) [STAY][4 digit user code], during the exit delay, hold [STAY] for 3 seconds ARM & STAY are ON
Bypass [BYP][4 digit user code][ON the button
corresponding to the zone], then [ENTER]. BYP is ON
To Reset smoke detector after
an alarm on zone 3 Press [CLEAR] and [ENTER] together
Default master code is [4747] or [474747]
Important note: Stay zone features MUST enable in [Step 1], or else it will not function
One-Touch Arming:
One-touch REGULAR arming Press & hold the [key 0/10] button for 3 seconds
One-touch STAY arming Press & hold the [key 11/STAY] button for 3 seconds
One-touch INSTANT arming Press & hold the [key 11/STAY] button for 3 seconds, then again Press
& hold again the [key 11/STAY] button for 3 seconds
Panic function:
Press [1] & [3] at the same time, for AUDIBLE POLICE PANIC alarm.
Press [4] & [6] at the same time, for AUDIBLE MEDICAL alarm.
Press [7] & [9] at the same time, for FIRE alarm.
Change Master / create new user code:
Press [ENTER] [Master code – 4747] [ 2 digit section, 00 for master, 01 for user 1, 02 for user 2…], then
[4 digits new code][ENTER][ENTER]
E.g.: [ENTER][4747][00] [5678][ENTER][ENTER], where 00 is master user and 5678 is the new master code.
[ENTER][5678][02] [2222][ENTER][ENTER], where 02 is user 2 and 2222 is the new user code.
[ENTER][5678][48] [5354][ENTER][ENTER], where 48 is user 48 and 5354 is the Duress code.
To delete user number:
Press [ENTER] [Master code – 4747] [ 2 digit section, 02 for user 2, 03 for user 3…] [press
2ND][ENTER][CLEAR]
E.g.: [ENTER][4747][02][Press 2ND][ENTER][CLEAR], user 2 is deleted.

8
Chime zone:
On 636 keypad
To activate chime for zone Press & hold any button from [1] to [6] for 3 seconds.
(Button 1 for zone 1, button 2 for zone 2…..)
To deactivate chime for zone Press & hold any button from [1] to [6] for 3 seconds
(Button 1 for zone 1, button 2 for zone 2…..)
To activate/deactivate chime for
keypad zone Press & hold button [8]
To activate/deactivate Buzzer Mute Press & hold button [9]
Clear TBL 8 – Timer loss
Press [master code:4747] [MEM] [HH:MM][ENTER]
E.g.: Press [ENTER][4747][MEM] [15:35][ENTER], enter current time 3:35pm.
V2.10 29092005