Paradox MG5000 User manual

User Guide
Always Armed,
Never Disarmed
MG5000
MG5050
SP65
SP4000
SP5500
SP6000
SP7000

Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on the
website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty
terms and conditions.
Limitations of Alarm Systems
We strongly advise that you review and take into consideration the “Limitations of Alarm Systems” document
available on our website at http://paradox.com/Terms/.
Warning for Connections to Non-Traditional Telephony (e.g. VoIP)
Paradox alarm equipment was designed to work effectively around traditional telephone systems. For those
customers who are using a Paradox alarm panel connected to a non-traditional telephone system, such as
"Voice Over Internet Protocol" (VoIP) that converts the voice signal from your telephone to a digital signal travel-
ing over the Internet, you should be aware that your alarm system may not function as effectively as with tradi-
tional telephone systems.
For example, if your VoIP equipment has no battery back-up, during a power failure your system's ability to
transmit signals to the central station may be compromised. Or, if your VoIP connection becomes disabled, your
telephone line monitoring feature may also be compromised. Other concerns would include, without limitation,
Internet connection failures which may be more frequent than regular telephone line outages.
We therefore strongly recommend that you discuss these and other limitations involved with operating an alarm
system on a VoIP or other non-traditional telephone system with your installation company. They should be able
to offer or recommend measures to reduce the risks involved and give you a better understanding.
WARNINGS: Information to User
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part
15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to equipment intermittently, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures: (1) re orient or relocate the receiving antenna; (2) increase the
separation between the equipment and receiver; (3) connect the equipment to an outlet on a circuit other than
the one to which the receiver is connected, or (4) consult the dealer or an experienced radio/tv technician for
assistance. CAUTION: The user is cautioned that any changes or modifications not expressly approved by Par-
adox Security Systems could void the user’s authority to operate/use the equipment.
Patents
One or more of the following US patents may apply: 7046142, 6215399, 6111256, 5920259, 5886632, and
RE39406. Canadian and international patents may also apply.
© 2014 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. Par-
adox, StayD, Magellan and Spectra are trademarks or registered trademarks of Paradox Security Systems
(Bahamas) Ltd. or its affiliates in Canada, the United States and/or other countries.

Magellan / Spectra SP 1
Table of Contents
Warranty .................................................................... 0
Limitations of Alarm Systems..................................... 0
Warning for Connections to Non-Traditional
Telephony (e.g. VoIP)......................................... 0
WARNINGS: Information to User............................... 0
Patents....................................................................... 0
User Settings .................................................................. 2
Zone Settings.................................................................. 3
User Codes...................................................................... 4
Adding / Modifying a User.......................................... 4
Deleting a User .......................................................... 4
Setting the Time & Date ................................................. 5
Setting Chime Zones...................................................... 5
Trouble Display............................................................... 6
Keypads........................................................................... 7
Auditory Feedback..................................................... 7
Visual Feedback ........................................................ 7
Keypad Muting........................................................... 7
Keypad Backlight ....................................................... 8
Power Save Mode (K32RF / K37 only)...................... 8
Keypad Overviews..................................................... 9
Remote Controls........................................................... 12
Remote Control Feedback (REM2).......................... 12
Arming & Disarming with StayD ................................. 12
To Turn On/Off StayD Mode.................................... 12
To Change Arm Mode.............................................. 13
Advanced StayD Settings ........................................ 13
Arming & Disarming..................................................... 14
Regular Arming........................................................ 14
Sleep Arming ........................................................... 14
Stay Arming ............................................................. 14
Bypassing a Zone.................................................... 15
One-Touch Arming................................................... 15
Auto-Arming............................................................. 16
Display Mode........................................................... 16
Alarms ........................................................................... 17
Alarm Display........................................................... 17
Disarming & Deactivating an Alarm ......................... 17
Panic Alarms............................................................ 17
Fire Alarms............................................................... 17
Testing & Maintenance............................................ 18
Communicating Through the Internet (IP100) ........... 18
Communicating Using Text Messages (PCS100)...... 18
Communicating by Phone........................................... 20
(Voice-Guided VDMP3) ................................................ 20
VDMP3 Instructions Diagram................................... 21
Advanced System Features ........................................ 22
Programmable Outputs (PGMs) .............................. 22
Partitioning............................................................... 22
Quick Function Keys................................................ 22
System Notes................................................................ 22
Quick Programming..................................................... 24
Master Quick Menus................................................ 24
Index.............................................................................. 26

2User Guide
User Settings
For security reasons, write only the user’s name and not their user code. 4-Digit Codes l6-Digit Codes l
*Programmed by your installer.
User # and Name Partition
1Partition 2Byp* Stay* Force* Arm* only PGM* only Duress*
01: Master Mas- l l lllll l
02: Master 1 Mas- l l l l l l l l
03: Master 2 Mas- l l lllll l
04:________________________________________ l l l l l l l l
05:________________________________________ l l lllll l
06:________________________________________ l l l l l l l l
07:________________________________________ l l lllll l
08:________________________________________ l l l l l l l l
09:________________________________________ l l lllll l
10:________________________________________ l l l l l l l l
11:________________________________________ l l lllll l
12:________________________________________ l l l l l l l l
13:________________________________________ l l lllll l
14:________________________________________ l l l l l l l l
15:________________________________________ l l lllll l
16:________________________________________ l l l l l l l l
17:________________________________________ l l lllll l
18:________________________________________ l l l l l l l l
19:________________________________________ l l lllll l
20:________________________________________ l l l l l l l l
21:________________________________________ l l lllll l
22:________________________________________ l l l l l l l l
23:________________________________________ l l lllll l
24:________________________________________ l l l l l l l l
25:________________________________________ l l lllll l
26:________________________________________ l l l l l l l l
27:________________________________________ l l lllll l
28:________________________________________ l l l l l l l l
29:________________________________________ l l lllll l
30:________________________________________ l l l l l l l l
31:________________________________________ l l lllll l
32:________________________________________ l l l l l l l l

Magellan / Spectra SP 3
Zone Settings
Write the device type (motion detector, door contact etc.) and location.
Zone Number and Description Partition
1 or 2 Byp Stay Sleep Force 24Hr Entry
delay Fire zone Fire Delay
001:______________________________ _____ llllllll
002:______________________________ _____ l l l l l l l l
003:______________________________ _____ llllllll
004:______________________________ _____ l l l l l l l l
005:______________________________ _____ llllllll
006:______________________________ _____ l l l l l l l l
007:______________________________ _____ llllllll
008:______________________________ _____ l l l l l l l l
009:______________________________ _____ llllllll
010:______________________________ _____ l l l l l l l l
011:______________________________ _____ llllllll
012:______________________________ _____ l l l l l l l l
013:______________________________ _____ llllllll
014:______________________________ _____ l l l l l l l l
015:______________________________ _____ llllllll
016:______________________________ _____ l l l l l l l l
017:______________________________ _____ llllllll
018:______________________________ _____ l l l l l l l l
019:______________________________ _____ llllllll
020:______________________________ _____ l l l l l l l l
021:______________________________ _____ llllllll
022:______________________________ _____ l l l l l l l l
023:______________________________ _____ llllllll
024:______________________________ _____ l l l l l l l l
025:______________________________ _____ llllllll
026:______________________________ _____ l l l l l l l l
027:______________________________ _____ llllllll
028:______________________________ _____ l l l l l l l l
029:______________________________ _____ llllllll
030:______________________________ _____ l l l l l l l l
031:______________________________ _____ llllllll
032:______________________________ _____ l l l l l l l l

4User Guide
User Codes
User codes are personal identification numbers for each user that allow you to enter certain programming
modes, arm or disarm your system, as well as activate or deactivate PGMs. The system supports the following:
• 1 System Master Code
• 2 Master Codes
• 29 User Codes
System Master Code (Default: 123456)
The System Master Code can arm or disarm any partition, and can create, modify or delete any user code.
Master Codes
Master Code 1 is permanently assigned to Partition 1 and can be used to create, modify or delete user codes
that are assigned to Partition 1. Master Code 2 is permanently assigned to Partition 2 (exception: when partition-
ing is disabled, Master Code 2 will be assigned to Partition 1) and can be used to create, modify or delete user
codes that are assigned to the same partition.
NOTE: Master Codes cannot modify or delete user codes assigned to both partitions. Only the System Master
Code can modify or delete user codes assigned to both partitions.
Duress Code
If you are forced to arm or disarm your system, entering the user code with the duress option enabled will arm or
disarm the system and immediately transmit a silent alert (Duress Code) to the monitoring station. The duress
code must be enabled by your installer.
User Code Length
Your system can be programmed to use either 4- or 6-digit user codes, where each digit can be any value from
0 to 9. Six-digit codes are considered more difficult to “crack” and therefore, more secure. Avoid programming
simple or obvious user codes, such as your telephone number, address, or codes such as 1234.
Adding / Modifying a User
Deleting a User
How do I add / modify a user? Visual Feedback
1Press the []key.
2 Enter your [MASTER CODE]. []and [1] flash. When a number on the
keypad is lit, the user is already programmed.
3 Select a user by entering a 2-digit user number (01 to 32). “Arm” flashes.
4 Enter a 4- or 6-digit [USER CODE]. “Sleep” flashes.
5 Confirm the [USER CODE]. “Stay” flashes.
6 To register a remote, press and hold any remote button for 3
seconds. Release. Press and hold any remote button for 3
seconds. If you do not wish to assign a remote, press
[ENTER].
“Off” flashes.
7 To program another user, go to step 3.
To exit, press [CLEAR].
For partitioned systems, continue to step 8.
8Press[1] and/or [2] to assign the user to a partition.
Press [ENTER].
9 To program another user, go to step 3.
To exit, press [CLEAR].
How do I delete a user?
1Press the []key.
2 Enter your [MASTER CODE].
3 Select a user by entering a 2-digit user number.
4 Press and hold the [SLEEP]key until you hear the confirmation beep.

Magellan / Spectra SP 5
Setting the Time & Date
Setting Chime Zones
A chime-enabled zone will advise you every time it is opened by causing your keypad to beep. Each keypad
must be chimed separately.
How do I set the time & date?
1Press the []key.
2 Enter your [MASTER CODE].
3Press[TBL].
4Press[5].
5 Enter time* in the [HH.MM]format. If HH = 13 or more, skip to step 7.
6 Select time format. [1] = 24hr; [2] = AM; [3] = PM.
7 Enter the date in the [YYYY/MM/DD]format. You have now set the time & date. Press [CLEAR]to exit.
*For SP4000 / SP65 systems, time must be entered in 24hr format. Omit step 6 (time format).
How do I chime zones?
•
•
•
•
For K32, K32+ and K32RF: Press & hold the [ ] key. The Arm1, Arm2, Stay1, and Stay2 LEDs will flash.
Enter the zone number corresponding to the zones you want to chime. The corresponding LED will light up.
Press the [ENTER]key to exit.
For K35 and K37: Press & hold the [ ] key (K35) or [ ] key (K37). The word Chime will appear on the
screen. Enter the zone number corresponding to the zones you want to chime. The corresponding LED will
light up. Press the [ENTER]key to exit. Note:K37 will only chime when powered by AC or when the display is
active.
For K10V, K10H and K636: Press & hold the zone key ([1] to [0(10)]). Accept beep = chime on.
For K32LCD, K32LCD+: Press and hold the [ ] key. Press [1] to select which zone to chime or press [2] to
configure chime period. The chime period allows you to specify the time frame in which the zone will chime.
Enter the zone number corresponding to the zones you want to chime. Press the [ENTER]key to exit.
How do I disable chime zones?
•
•
For K32, K32+,K32RF, K35, K37, K32LCD and K32LCD+: To disable chime zones, repeat this process
and enter the zone number to disable a chime zone, or press [SLEEP]to disable all chime zones instead of
entering a zone number.
For K10V, K10H and K636: Press & hold the zone key ([1] to [0(10)]). Fail beep = chime off.
NOTE:For a description of the confirmation and rejection beeps, see Keypad Feedback on page 7.
To identify your keypad, see page 9.

6User Guide
Trouble Display
Your alarm system continuously monitors several trouble conditions that can be reported directly to your moni-
toring station. When a trouble condition occurs, the [TBL]key will illuminate. Press the [TBL]key, and the keypad
will illuminate a number corresponding to the trouble the system is experiencing. Except for the Timer Loss trou-
ble, contact your monitoring station or installer to resolve the trouble condition.
NOTE: If the keypad emits a BEEP every 5 seconds whenever a new trouble condition has occurred, press the
[TBL]key to stop the “Trouble Beep”.
Accessing the Trouble Display
Press
[TBL]
Key / LED
Lit Trouble Type Trouble Details
[1] Wireless Zone Low Battery The batteries for one of the system’s wireless
devices needs to be replaced.
[2] Power Trouble The control panel is experiencing power trouble.
[3] Bell Trouble There is a bell disconnect/overload on the control
panel.
[4] Communication Trouble Your alarm system, if monitored, could not
communicate with the monitoring station.
[5] Tamper/Zone Wiring Failure A wiring problem is occurring on one or more
devices.
[6] Module Tamper Trouble A device’s anti-tamper switch has been triggered.
[7] Fire Loop Trouble One of the zones is in fire loop trouble.
[8] Timer Loss Your alarm system’s clock must be reprogrammed.
See Setting the Time and Date on page 5 to set your
system’s time and date.
[9] Wireless Zone Supervision Loss One or more wireless zones are no longer
communicating with the system.
[0 (10)] Module Supervision Loss One or more modules are no longer communicating
with the system.
[16] /
[SLEEP]Keypad Fault There is a problem with one of your system’s
keypads

Magellan / Spectra SP 7
Keypads
Auditory Feedback
When you enter information on the keypad, it will guide you with beep tones that communicate confirmation or
rejection of your entries. You should be familiar with these two keypad beep tones:
Confirmation Beep:When an operation (e.g. arming/disarming) is successfully entered on the keypad or when
the system switches to a new status/mode, the keypad produces an intermittent beep tone (“BEEP-BEEP-BEEP-
BEEP”).
Rejection Beep:When the system reverts to its previous status or when an operation is incorrectly entered on
the keypad, it will emit a continuous beep tone (“BEEEEEEEEP”).
The following are other types of auditory feedback, and will always be accompanied by the flashing of an arm
key or LED ([ARM], [STAY], or [SLEEP]):
• Continuous beep = Alarm
• Variable beep = Fire alarm
• Intermittent beep = Beginning of exit delay
• Fast Intermittent beep = Last 10 seconds of exit delay
Visual Feedback
The keypad includes colored lights which convey the current status of your system. The state of each light rep-
resents a specific condition in your system.
NOTE: Many of the features in your system must be enabled by the installer. If the feature is not programmed,
the keypad will emit a rejection beep and the action will be canceled. Refer to Zone Settings on page 3 for
details.
Keypad Muting
When muted, the keypad will only emit the confirmation beep and rejection beep, and will beep when a key is
pressed. Therefore, when muted, the keypad will not beep during an alarm and will not beep for chime enabled
zones. Each keypad must be muted separately.
How do I mute the keypad?
• For K32, K32+, K32RF, K35, K37, K636, K10V and K10H: Press & hold the [CLEAR] key for 6 seconds to
enable or disable keypad muting. If the keypad emits a confirmation beep, Keypad Muting is enabled for
that keypad. If the keypad emits a rejection beep, the feature is disabled.
For the K32LCD, K32LCD+: Press and hold the [ ] key for keypad settings. Press [4] for Mute Control.
Press [arm] to enable or disable keypad muting.

8User Guide
Keypad Backlight
The illumination level behind the keys can be modified to suit your needs.
Power Save Mode (K32RF / K37 only)
If DC power is not supplied to the wireless keypad, the module’s display will shut off and go into power save
mode after one minute (20 seconds for K37). Press the []key to activate the display.
How do I modify the backlight?
• For K32, K32+ and K32RF: Press and hold the []key. Press the []key to set the desired backlight level.
Press [CLEAR]or [ENTER] to exit.
For K35: Press and hold the []key for 4 seconds. Keys 1, 2, 3, 5 and 6 will flash. Press [CLEAR] to exit
the menu without saving the information or press [ENTER] to exit the menu and save the information. Press
the desired key and scroll using the [] and []to adjust:
[1] To adjust the scrolling speed.
[2] To adjust the backlight (0 = Off, 1 = Lowest brightness / 7 = Maximum brightness)
[3] To adjust the contrast (0 = Low contrast, 4 = High contrast)
[5] To adjust the auto dim backlight level (0 = Off, 1 = Lowest auto dim backlight, (...) 7 = Highest auto dim
backlight
[6] To adjust the auto dim delay (0 = Off, 1 = 1 sec., 2 = 5 sec., 3 = 10 sec., 4 = 20 sec., 5 = 1 min., 6 = 2
min., 7 = 4 min.)
For K37: Press and hold the [] key for 4 seconds. Keys 1 and 2 will flash. Press [CLEAR] to exit the menu
without saving the information or press [ENTER] to exit the menu and save the information. Press the
desired key and scroll using the []and [] to adjust:
[1] To adjust the backlight.
[2] To adjust the auto dim delay (5 = 5 sec. / 15 = 15 sec.)
For the K10V, K10H and K636: Press and hold the [MEM]key. The [MEM]key will illuminate. Press the
[MEM]key to set the desired backlight level. Press [CLEAR] or [ENTER]to exit.
For the K32LCD, K32LCD+: Press and hold the []key. Press [2] to modify the backlight. Scroll using the
[] and [] keys. Press [ENTER]to save.

Magellan / Spectra SP 9
Keypad Overviews K636 Keypad Overview
K10LEDV/H Keypad Overview
[TBL] Trouble display
ON = Trouble(s) occurring (page 6)
[MEM] Alarm memory display
ON = Alarm(s) occurred (page 17)
[BYP] Bypass programming
ON = Zone(s) bypassed (page 17)
Zone Display:
The keys [1] to [0(10)] correspond
to zones 1 to 10 respectively:
Key lit= Open or entry delay
Key flash= In alarm
Off Key:
ON= Disarmed
OFF = System armed
Light (AC):
ON = Power on
OFF = Power off
StayD Light:
ON= StayD on
OFF= StayD off
(see StayD Mode on
page 12)
[ARM] (page 14)
[SLEEP] (page 14)
[STAY] (page 14)
ON = System armed
OFF = Zone disarmed
Flash = Exit Delay
Fast Flash = Exit Delay (final 10 sec.) / zone in
alarm
IMPORTANT: If installed on
a partitioned system, the
K636 will only display parti-
= Press once + [MASTER CODE]for
Quick Menu Programming (see
Master Quick Menus on page 24)
Partition 1
[TBL] Trouble display
ON = Trouble(s) occurring (page 6)
[MEM] Alarm memory display
ON = Alarm(s) occurred (page 17)
[BYP] Bypass programming
ON = Zone(s) bypassed (page 17)
Zone Display:
The keys [1] to [0(10)] correspond
to zones 1 to 10 respectively:
Key lit= Open or entry delay
Key flash= In alarm
= Press once + [MASTER CODE]for
Quick Menu Programming (see
Master Quick Menus on page 24)
Off Key:
ON= Disarmed
OFF = System armed
Light (AC):
ON = Power on
OFF = Power off
StayD Light:
ON= StayD on
OFF= StayD off
(see StayD Mode on
page 12)
[ARM] (page 14)
[SLEEP] (page 14)
[STAY] (page 14)
ON = System armed
OFF = Zone disarmed
Flash = Exit Delay
Fast Flash = Exit Delay (final 10 sec.) / zone in
alarm

10 User Guide
K35 and K37 Keypad Overview
K35 and K37 Icon Display and Description
= Press once + [MASTER CODE]for
Quick Menu programming
(see Master Quick Menus on page 24)
= Press & hold for keypad settings
= Press & hold for chime programming
(see Setting Chime Zones on page 5)
Icon Description Icon Description
StayD On = StayD mode enabled Flashing = System is in Master Quick Menu mode
Indicate Partition 1 and 2 EXIT DELAY Flashing = Enter code before Exit Delay ends
OFF On = System is disarmed ENTRY DELAY Flashing = Enter code before Entry Delay ends
STAY On = System is Stay armed ENTER CODE On = Enter your user code
SLEEP On = System is Sleep armed MEMORY On = Alarm(s) occurred
ARM On = Partition is armed BYPASS On = Zone(s) bypassed
ALARM Flashing = System is in alarm CHIME On = Displays chime zones when in Chime Prog.
mode
PRE-ALARM
DELAY On = Countdown to alarm on Pre-Alarm zones TROUBLE Trouble flashes andnumber(s) corresponding to the trouble(s) illuminate (see Trouble List on page 6)
ZONE OPEN On = Illuminated zone(s) are open AC On = AC power is supplied to the keypad
ZONE IN ALARM On = Illuminated zone(s) are in alarm NO AC On = Keypad is running on backup battery power
TX (K37 only) Flashing = Communication with panel in progress
K35 K37

Magellan / Spectra SP 11
K32, K32+ and K32RF Keypad Overview
K32LCD+ and K32LCD Keypad Overview
[TBL] Trouble display
ON = Trouble(s) occurring (page 6)
[MEM] Alarm memory display
ON = Alarm(s) occurred (page 17)
[BYP] Bypass programming
ON = Zone(s) bypassed (page 17)
Zone Display:
The keys [1] to [0(10)] correspond
to zones 1 to 10 respectively:
Key lit= Open or entry delay
Key flash= In alarm
[ARM] (page 14)
[SLEEP] (page 14)
[STAY] (page 14)
ON = System armed
OFF = Zone disarmed
Flash = Exit Delay
Fast Flash = Exit Delay (final 10 sec.) / zone in
alarm
Off Key:
ON= Disarmed
OFF= System armed
Light (AC):
ON = Power on
OFF = Power off
StayD Light:
ON= StayD on
OFF= StayD off
(see StayD Mode on
page 12)
Power and Rx/Tx Light (K32RF only)
On = Power on
Off = Power off
Fast Flash = Transmission/Reception in progress
Slow Flash = AC Loss on Keypad
lnfo Key (K32RF only)
Refresh display to see all open zones (see page 8)
= Press once + [MASTER CODE]for
Quick Menu Programming (see
Master Quick Menus on page 24)
= Press and hold to modify backlight
(see page 8)
Partition 1 Status Partition 2 StatusPartition 1 Status Partition 2 Status Partition 1 Status Partition 2 Status
[TBL] Trouble display
ON = Trouble(s) occurring (page 6)
[MEM] Alarm memory display
ON = Alarm(s) occurred (page 17)
[BYP] Bypass programming
ON = Zone(s) bypassed (page 17)
Off Key:
ON= Disarmed
OFF = System armed
Light (AC):
ON = Power on
OFF = Power off
StayD Light:
ON= StayD on
OFF= StayD off
(see StayD Mode on
page 12)
= Press once + [MASTER CODE]for
Quick Menu Programming (see
Master Quick Menus on page 24)
= Press and hold to modify back light
(see page 8)
= Press and hold for chime programming
(see page 5)

12 User Guide
Remote Controls
Your security system supports three types of remote controls; the REM1, REM2, REM3 and REM15. The REM1
and REM15 are the most basic remote controls, with the ability to perform five actions (e.g. arming, disarming,
activating a PGM, etc.). The REM2 is more advanced, as it performs up to six different actions, as well as pro-
vides visual and auditory feedback (see table below). The REM3 is the most advanced remote control, as it has
all the functionalities of a keypad (refer to the REM3 User Manual for more information). The following table
describes the visual and auditory feedback of the REM2 remote control.
NOTE:A wireless expansion module is necessary in order to use remote controls if you are using a Spectra SP
system. Please refer to your installer for more information regarding the use of remote controls with a Spectra
SP system.
Remote Control Feedback (REM2)
Full/Force Arming Feedback
Stay/Sleep Arming Feedback
Other Feedback
Arming & Disarming with StayD
StayD simplifies your life and makes it safer by protecting you 24 hours a day, 7 days a week without ever hav-
ing to disarm the system – even when entering an armed area. StayD lives with you and protects you at all
times, without any unprotected periods, and automatically re-arms the system so you don’t need to remember
to.
When entering/exiting a site, the system partly disarms to let you pass through: simply notify the system with
your remote and go through the designated path which will automatically re-arm after you pass. All other zones
remain armed. The result is a system that is always protecting, without the uncertainty of whether the system is
armed or not.
Other benefits of StayD include knowing when your kids are accessing potentially dangerous areas, such as the
balcony, pool or front door. Now you can truly have peace of mind knowing that you are always protected. Con-
sult your installer for more information.
To Turn On/Off StayD Mode
To turn on StayD mode:
[STAY] +[CODE] +[STAY] StayD light on
Press the [STAY]key followed by a valid code, then press the [STAY]key again within ten seconds. The StayD
light will light up to confirm StayD activation, and the system will be in Stay mode.
Action Visual Feedback Auditory Feedback
Disarming Green on Two beeps
Exit delay Red / green slow flash Confirmation beep
Arming / Entry Delay Red on Confirmation beep
Alarm Red fast flash Alarm beep
Action Visual Feedback Auditory Feedback
Disarming Green on Two beeps
Exit delay Yellow / green slow flash Confirmation beep
Arming / Entry Delay Yellow on Confirmation beep
Alarm Red fast flash Alarm beep
Action Visual Feedback Auditory Feedback
PGM on/off Yellow on Confirmation beep

Magellan / Spectra SP 13
To turn off StayD mode:
[OFF] +[CODE] +[OFF]Off light on
Press the [OFF]key followed by a valid code, then press the [OFF] key again within ten seconds. The StayD light
will turn off and the Off light will light up to confirm StayD deactivation. With StayD disabled, the system will func-
tion as a standard security system.
To Change Arm Mode
(see Arming & Disarming on page 14)
To change the level of security - Stay to Sleep:
[SLEEP]for 2 sec. Delay Sleep light on
Press and hold the [SLEEP]key on any keypad. All zones which will be armed in Sleep mode go into exit delay,
allowing you to move to the bedroom. When the exit delay ends, and you are in the bedroom, the rest of the
interior will arm. The system is now in Sleep mode.
To change the level of security - Sleep to Stay:
[STAY]for 2 sec. Stay light on
Press and hold the [STAY]key on the keypad located in the bedroom. The system will instantly switch from
Sleep to Stay mode, allowing you to leave the bedroom and move freely inside the house. If you accidentally
leave the bedroom without switching to Stay mode, all zones armed in Sleep mode will go into a delay, allowing
you enough time to switch to Stay mode.
Leaving the site - Stay to Full:
Keypad: [ARM]for 2 sec. Delay Arm light on
Press and hold the [ARM]key on the keypad that the exit path is assigned to. This will start an exit delay period
for all zones in the exit path. After you have left the property, all exit path zones will rearm. The system is now in
Full mode.
Entering the site - Full to Stay:
Keypad: [CODE] Stay light on
When entering the property through the entry path, all zones assigned to the entry path will go into delay, allow-
ing you to enter the house. Entering a valid code on the keypad the entry path is assigned to ends the entry
delay and switches the system to Stay Arm mode. The entry path zones will rearm. The system is now in Stay
mode.
Leaving the site without changing arm mode:
[OFF]for 2 sec.
Press and hold the [OFF]key for 2 seconds on a keypad to leave the site without changing arm mode.
Advanced StayD Settings
Window Mode and Re-arm Delay
In a Stay-armed system: This mode allows you to open one exterior zone without triggering an alarm. To enter
Window mode, press [OFF], then your [USER CODE]. All zones that can be opened flash. The system will start an
exit delay, allowing you to open an exterior zone such as a window or a door. The system will only allow you to
open one zone as the exit delay will end after doing so. When you close the open zone (window, door, etc.) that
zone will re-arm.
When closing an exterior zone such as a window or door, a delay will start allowing you to close the zone prop-
erly. The re-arm delay starts when you close the zone, and you must keep the zone closed for the entire delay
period for it to re-arm. This is especially useful for windows that stick thus reducing false alarms.
Live View Mode:
During an alarm, press the [CLEAR] key to view the movement. The zone lights on the keypad will show the
opening and closing of zones as they occur.

14 User Guide
Arming & Disarming
Take full advantage of your system by familiarizing yourself with all the arming methods. If your system is not
partitioned (see Partitioning on page 22), everything is considered as belonging to Partition 1.
NOTE: If you cannot arm because a zone is open, the system will enter in Bypass Programming. Enter the two
digit zone you wish to bypass and press [ENTER], or press [ENTER] to bypass all open zones.
Regular Arming
This method will arm all the zones in the selected partition. Please note that Regular arming can also beactivated
using Auto-Arming (see Auto-Arming on page 16) or One-Touch Arming (see One-Touch Arming on page 15).
Sleep Arming
Similar to Stay arming, Sleep arming allows users to remain in a protected area, but provides a higher level of
protection. For example, in a two-story house, the perimeter is protected with Stay arming. With Sleep arming,
the perimeter as well as the main floor are protected (motion detectors, etc.), allowing you to roam the second
floor and sleeping quarters. Sleep zones are zones that are bypassed when Sleep arming. For example, when
you go to sleep at night, the entire premises except your bedroom is fully armed. Sleep arming can also be acti-
vated using Auto-Arming (see Auto-Arming on page 16) or One-Touch Arming (see One-Touch Arming on
page 15).
Stay Arming
This method allows you to roam freely within the premises while the perimeter is fully armed. Stay zones are
zones that are bypassed when Stay arming. For example, if you plan on staying in for the night, doors and win-
dows can be armed without arming other zones like motion detectors. Stay arming can also be activated using
Auto-Arming (see Auto-Arming on page 16) or One-Touch Arming (see One-Touch Arming on page 15).
How do I Regular arm?
1 Close all zones in the desired partition.
2Press[ARM] +[USER CODE].
3 If you have access to both partitions (see Partitioning on page 22): Press the key corresponding to the
desired partition ([1] or [2]).For both partitions, press the other key after the confirmation beep.
How do I Sleep arm?
1 Close all zones in the desired partition (except Sleep zones).
2 Press the [SLEEP]key.
3 Enter your [USER CODE].
4 If you have access to both partitions (see Partitioning on page 22): Press the key corresponding to the
desired partition, [1] or [2].For both partitions, press the other key after the confirmation beep.
How do I Stay arm?
1 Close all zones in the desired partition (except Stay zones).
2 Press the [STAY]key.
3 Enter your [USER CODE].
4 If you have access to both partitions (see Partitioning on page 22): press the key corresponding to the
desired partition, [1] or [2].For both partitions, press the other key after the confirmation beep.

Magellan / Spectra SP 15
Bypassing a Zone
Bypassing a zone allows you to ignore (deactivate) specified zones the next time the system is armed. For
example, you may wish to bypass certain zones when workers are renovating part of your home. Once the sys-
tem is disarmed, the bypass entries are erased. When zones are bypassed, the [BYP]key will illuminate. Zone
bypassing can also be activated by using One-Touch Bypass Programming (see page 15). If One-Touch Bypass
Programming is enabled, press the [BYP] key for three seconds to enter bypass programming. To remove the
Bypass feature from a zone, in step 3 enter the zone number again or press [CLEAR]to erase all current entries.
Press [CLEAR] +[ENTER]to delete bypassed zones.
Bypass Recall Feature
After disarming the system, bypass entries are erased. The Bypass Recall feature reinstates the previous
bypass entries saved in memory. This eliminates the need to manually re-program the bypass entries every time
you arm your system.
One-Touch Arming
One-Touch arming allows you to arm the system without using a user code. This feature must be enabled by
your installer. If One-Touch Arming is programmed, you can increase the security level of your system (from Dis-
arm Stay Arm Sleep Arm Full Arm) without a code. See Figure 1 below.
One-Touch Regular Arming
Press and hold the [ARM]key to arm all zones in the partition. If partitioned, keys [1] & [2] will flash. You can use
this feature to allow specific individuals like service personnel (e.g. cleaners) to arm without giving them access
to any other alarm system operations. See Regular Arming on page 14.
One-Touch Stay Arming
Press and hold the [STAY]key to arm the perimeter (no Stay zones). See Stay Arming on page 14.
One-Touch Sleep Arming
Press and hold the [SLEEP]key to arm all zones not defined as Sleep zones. See Sleep Arming on page 14.
One-Touch Bypass Programming
Press and hold the [BYP]key to access Bypass programming mode. See Bypassing a Zone on page 17.
Fast Exit
When the system is already Stay or Sleep armed: this feature will allow you to exit already armed premises and
keep the system armed. Press and hold the [OFF]key for to start the exit delay. After the exit delay has elapsed,
the system will switch to its previous arming mode.
How do I bypass zones?
1 Press the [BYP]key.
2 Enter [USER CODE].The [BYP] key will flash. Press [ENTER]to bypass all open zones or go to step 3.
3 Illuminate the number(s) corresponding to the zone(s) you want to bypass by entering the zone number.
Solid on = Zone open, Flash = Zone bypass, Off = Zone closed, not bypassed.
4 Press the [ENTER]key to save and exit. Press [CLEAR]twice to exit without saving.
How do I recall bypass entries?
1 Press the [BYP]key.
2 Enter your [USER CODE].
3 Press the [BYP]key.
4 Press the [ENTER]key.

16 User Guide
Figure 1: Arming / Disarming
Auto-Arming
Timed Auto Arming
The alarm system can automatically arm itself at a specified time every day. As with Regular arming (see Regu-
lar Arming on page 14), the system will bypass any open zones.
No Movement Auto Arming
The alarm system can be programmed to arm the system and/or send a report to your monitoring station if no
zone activity occurs for a pre-programmed amount of time. This is a particularly useful feature when supervising
an individual with chronic health problems or for a person who lives alone. The system will bypass any open
zones.
Display Mode
The K32RF has two display modes. By default, the keypad will show all events (e.g. zones in alarm, bypassed
zones, etc.) live as they occur. Alternatively, the system can be programmed by your installer to only display
zones that cause an alarm or entry delay. If you want to see the status of all zones, press the []key. Zones that
are open but have not triggered an alarm will only be displayed after pressing the []key. The information will
be displayed for 30 seconds (20 seconds for K37), showing the status of all zones at the time the []key was
pressed. The zone display will shut off after 30 seconds (20 seconds for K37). For more information on the two
display modes, contact your installer.
How do I program the Auto-Arm Timer?
1Press the []key.
2 Enter [MASTER CODE].
3 Press the [BYP]key. The [BYP]key will flash.
4 Press key [1] to set partition 1, or press key [2] to set partition 2.
5 Enter the desired time for auto arm (24 hour clock, e.g. 18:30).
6 Press key [1] to regular arm, key [2] to sleep arm, or key [3] to stay arm the partition.
How do I temporarily disable the Auto-Arm Timer?
1Press the []key.
2 Enter [MASTER CODE].
3 Press the [BYP]key. The [BYP]key will flash.
4 Press key [1] to set partition 1, or press key [2] to set partition 2.
5 Press and hold [SLEEP]to temporarily disable the Auto-Arm Timer.

Magellan / Spectra SP 17
Alarms
Alarm Display
If an alarm has occurred on a zone, the respective zone key will flash, the [MEM] key will light up, and the zones
will be stored in memory. These respective keys will continue to flash until disarming even if the zones are
restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR]key. When the
system is disarmed, the zone keys will turn off, while the [MEM] key remains lit. Press the [MEM]key to illuminate
the key corresponding to the zones that were in alarm. The alarm memory will be erased when the next alarm
occurs and after a valid code is entered or upon full-arming the system.
Disarming & Deactivating an Alarm
To disarm an armed system or an alarm, press [OFF]and enter your [USER CODE]. An entry point, like the front
door, will be programmed with one of two Entry Delay Timers. When an entry point is opened, the keypad will
beep until you disarm the system. Your alarm system will not generate an alarm until this timer elapses. Any
user can disarm a partition they have been assigned to, except users assigned with the Arm Only Option or
PGM Only Option.
Panic Alarms
In case of an emergency, the system can provide three panic alarms that can immediately generate an alarm
after simultaneously pressing and holding two specific keys for three seconds. Based on your needs, these
panic alarms can generate audible alarms (sirens or bells) or silent alarms and can communicate specific mes-
sages to your monitoring station. For instance, pressing [1] and [3] can mean “call the police” or anything you
require. This feature must be set by your installer.
Press and hold keys [1] and [3] for Panic type 1 (e.g. police).
Press and hold keys [4] and [6] for Panic type 2 (e.g. medical).
Press and hold keys [7] and [9] for Panic type 3 (e.g. fire).
Fire Alarms
Upon a fire alarm, the bell/siren will emit three “squawks” at 2 second intervals until silenced or reset by entering
a valid user code. If the zone is a Delayed Fire Zone, there is a delay before the system contacts the monitoring
station. This will prevent unnecessary reporting of false alarms. If there is no fire condition, contact your monitor-
ing station immediately to avoid an unnecessary response.
Minimizing Fire Hazards
The three most common causes of fires:
Cooking is the leading cause of home fires in the U.S. It's also the leading cause of fire injuries. Cooking fires
often result from unattended cooking and human error, rather than mechanical failure of stoves or ovens. Care-
less smoking is the leading cause of fire deaths. Smoke detectors and smolder-resistant bedding and uphol-
stered furniture are significant fire deterrents. Heating is the second leading cause of residential fires. However,
heating fires are a larger problem in single family homes than in apartments since the heating systems in single
family homes are often not professionally maintained.
How do I disarm the system?
• Press [OFF]+ enter [USER CODE].
What do I do if a delayed fire zone was set off accidentally?
1 Press the [CLEAR]key within 30 seconds of the alarm.
2 Try to correct the problem.
3 If the problem persists, after 90 seconds, the alarm will sound again. Press the [CLEAR]key again.

18 User Guide
Fire Safety Tips
In the event of a fire, escape first, then call for help. Develop a home fire escape plan and designate a meeting
place outside. Make sure everyone in the family knows two ways to escape from every room. Practice feeling
your way out with your eyes closed. Never stand up in a fire, always crawl low under the smoke and try to keep
your mouth covered. Never return to a burning building for any reason; it may cost you your life. Finally, having
at least one working smoke alarm dramatically increases your chances of surviving a fire. And remember to
practice a home escape plan frequently with your family.
Providing a Fire Warning System
Household fires are especially dangerous at night. Fires produce smoke and deadly gases that can overcome
occupants while they sleep. To warn against fire, smoke detectors should be installed outside each separate
sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit,
including basements.
Testing & Maintenance
With the system disarmed and the “OFF” light illuminated, activate motion detectors by walking in the protected
area. Open and close protected doors and verify that the corresponding lights illuminate. Your installer can
advise you of the best way to test your particular system.
Do not use open flame or burning materials to test your fire detection devices. Contact your installer for safe
methods of testing your system.
Under normal use, your system requires virtually no maintenance other than regular testing. It is recommended
that the standby battery be changed every three years. Speak to your installer about the necessary tests and
how often they should be performed.
Communicating Through the Internet (IP150)
You can communicate with your security system via the internet by using a system accessory called the IP150
Internet Module (sold separately). The IP150 controls and monitors your security system remotely through any
web browser. It allows for email notifications of important system events such as alarms, arm/ disarm events,
and troubles. For example, receive an email at work when your kids get back from school, or if an alarm occurs
in your system at home.
You can also view live status of your system and arm/disarm your system. For example, you have just left your
office for the weekend but are not sure you remembered to arm it. Simply check the status of your system from
a laptop and arm it remotely. There is no PC software to install, as the IP150 is web-based. It uses a user-
friendly web-page that puts you in control. Consult your installer or refer to the IP150 User manual for more
information.
Communicating Using Text Messages (PCS250/PCS250G)
You can communicate with your security system using text messages (SMS) by using system accessories
called PCS250/PCS250G GSM modules (sold separately). The GSM module allows you to receive text mes-
sages of system events, such as alarms or troubles, on your cellular phone. It also allows you to send text mes-
sages to arm or disarm your system from anywhere in the world. Consult your installer for more information.
Receiving Text Messages
To receive text messages from your system you need to:
• Program the telephone numbers you wish to receive text notifications.
• Select which event groups (alarm, arm/disarm, trouble and trouble restore) will generate text messages.
• Select which partition the phone number is assigned to.
How do I set up the GSM module to send me text messages?
1Press the []key.
2 Enter [MASTER CODE].
3Press[ARM].