Paradox Marine Magel 6130 User manual

1
Installation Manual
Marine Magellan 6130/6160
Table of Content
Introduction……………………………….....2
Section 1: Installation Consideration…...2
Supply Voltage Considerations...........................2
Location Considerations…….…………...............3
Section 2: Mounting………………………..4
Marine Magellan……………………………..........4
Artion GSM Module…………………....................5
Artion Battery Backup...…………………………...5
Section 3: Electrical Installation…………7
AC Installations………………….…………………7
DC Installations……………...………………….....9
Internal Battery Backup / Marine Magellan…......9
Communication Lines…………………..….…..….9
Section 4: Programming…………………...12
1 –Language……………………………………..12
2 - User Profile……………………………………12
3 –Communicator………………………………..14
4 –Delays and Tones……………………………17
5 –System Test…………………………………..17
6 - Zone Profile: Overview…………………..…..18
Zone Definitions………………………..18
Zone Hardware Descriptions…………20
DCTXP2…………………..…….……...20
PMD-75 Motion Detector……………...22
SD-738 Smoke Detector………………23
Battery Low Voltage Detector………...23
High Water Alarm……………………...25
6 - Zone Profile: Programming…………...……..25
7 –Output Profile: Overview…………………….27
PGM Activation Events ……………….27
PGM Electrical Installation……………29
7 –Output Profile: Programming……………….29
8 –Keypad Profile Overview………………..…..31
8 - Keypad Profile Programming……….……....33
9 –Repeater Profile Overview………...………..33
9 - Repeater Profile Programming……..……….33
10 –Signal Strength………………………..........34
11 –Passwords…………………………..……....34
Console Trouble…………………………..……...35
AC Diagram……………………………………….37
DC Diagram……………………………………….38
PGM Wiring Examples………………………39 -42
Programming web…………………………...…...43
Marine Magellan Keypad Description…….…......4
id85386625 pdfMachine by Broadgun Software - a great PDF writer! - a great PDF creator! - http://www.pdfmachine.com http://www.broadgun.com

2
Introduction
Congratulations on your purchase of the Marine Magellan wireless security and
monitoring system for your yacht (Diagram 1). The system is designed to provide reliable
protection giving you true piece of mind when you are away from your vessel. This guide is
designed to walk the installer through the complete setup and basic wireless programming of the
Marine Magellan System. Please read the manual thoroughly before beginning. It is
recommended that the installer have a basic understanding of electrical fundamentals and
adheres to the ABYC standards of marine electronics.
Diagram 1

3
Section 1:
Installation Consideration
The placement of the individual
components of the Marine Magellan system
is very important. The installer must make
sure that adequate security concerns and
end user “ease of use”are taken into
account. Reference the following guidelines
before drilling any holes or running any
wires.
Supply Voltage
The Marine Magellan wireless security
and monitoring system must be installed in
an adequate and well thought out location
on your vessel. The system can be
powered from the vessels 110 AC (VAC)
supply and stepped down through our 16
VAC transformers. It can also be powered
by the vessels domestic battery banks 12
volts DC (VDC). It is important to establish
what voltage supply best suits your vessels
needs. Typically an AC power source is
used on all vessels that have a constant AC
source from shore power or a generator.
Powering the system through the vessels
battery banks is typically done on smaller
boats where AC power is not constant
Wire needs
-18 AWG / 2 conductor wire
Approximately 20 ft.
- Communication wire / 2 conductors
Telephone wire, Cat 5, or similar
approximately 12 ft.
AC installation
There must be a constant 110 VAC
source in the vicinity of the units for power.
The 16 VAC transformer must plug into the
110 VAC outlet. It is suggested that an
isolated outlet be installed strictly for the
plug in transformer(s). The 16 VAC output
feeds to the Marine Magellan head unit and
another transformer can feed to the Artion
Battery backup board. The Artion Battery
backup converts this 16 VAC to 12 VDC
while charging the battery backup for the
Artion. It is important that this AC source be
constantly powered when the boat is not
being used. It is suggested that you power
the system off of its own breaker.
DC installation
There must be a constant 12 Volt DC
(Direct Current) source in the vicinity of the
units for power. This 12 VDC must feed the
Marine Magellan and the Artion GSM
module directly. On DC installations the
Artion battery backup is not used.
Location Considerations
The Marine Magellan and the Artion
GSM Module must be mounted on the
interior of vessel. They should be
located as centrally as possible to all the
proposed zones. This area must be
clear from moisture and not susceptible
to drastic temperature changes.

4
There must be an adequate wire run
behind the Marine Magellan, Artion, and
the Artion Battery Backup Case (if
applicable) so wiring is not exposed.
Exposed wires compromise the systems
security as intruders could cut essential
communication lines. The installer must
properly research the proposed
locations of the devices so they have a
clear unobstructed wire run. The Marine
Magellan head unit and Artion unit
should be powered up and
communicating with no wire susceptible
to tampering.
The Artion should be as high as
possible on your vessel, mounted above
the water line for best cellular
communication, and located within 12 ft
of the Marine Magellan head unit. Use
the included 3 ft. extension cable to
extend the antenna and assist with the
clarity of the call.
It is important that the Artion be
accessible but not visible. This is
because in the event of an alarm, you
do not want the communication tool
exposed to any thieves. Possible
places include inside cabinets or behind
removable panels.
Section 2: Mounting
Once you have found an adequate
location for the Marine Magellan, Artion, and
the Artion Battery Backup Case (if
Applicable) according to the criteria on the
previous pages, it is time to mount them.
Marine Magellan
The Marine Magellan uses a plastic wall
plate for wall mounting (Diagram 2). If
mounting the unit on the wall you must first
pop out the rectangular cutout labeled D on
the plate to allow wiring access.
Diagram 2
The Marine Magellan can be mounted on a
wall by first securing the wall plate to the
wall and then mounting the console on the
secured wall plate.
1.) Place the wall plate on the desired spot
of the wall.
2.) Drill and insert screws into holes labeled
A as shown Diagram 2
3.) With the Rectangular cutout D removed
you must now drill a 5/8 inch hole into the
wall as to allow for wiring access from the
rear of the Marine Magellan.

5
Diagram 3
3. Place the console back plate flush against
the mounted wall
plate as shown in Diagram 3.
4. Slide the Marine Magellan’s open slots
labeled F (Diagram 3) onto the wall plate’s
tabs labeled B.
5. Gently apply downward pressure to insert
the wall plates
tabs into Marine Magellan’s open slots.
6. Once the Marine Magellan’s power and
communication wires are hooked up
(Electrical Installation, Page 8), Insert two
screws through the wall plate’s screw holes
labeled C and into holes labeled E (
Diagram 3 ) in the Marine Magellan back
plate. This will secure the console to the
wall.
Artion GSM Module
It is important that the GSM communication
module be mounted in such a location to
allow accessibility without obvious visibility.
Follow the steps below.
1.) Establish a proper location
2.) Mark the necessary holes to mount the
Artion and allow wiring access.
3.) Drill the mounting holes
4.) Drill the 5/8 wiring access hole
5.) Screw in the top two screws on the
left and right side of the area. Leave
approximately 1/8 inch between the wall
and the underside of the screw head.
6.) Feed your power, trigger and
communication wires through the wiring
hole.
7.) Place the GSM cellular module onto
the top two screws matching up the
respective holes and push downwards
to lock the unit into place.
8.) Depress the two tabs at the base of
the GSM cellular module and remove
the top Cover.
9.) Screw the final two screws on the
bottom of the GSM cellular module.
10.) Place cover back on Artion.
Artion Battery Backup
This case should be mounted in the vicinity
of the Artion. There are four screw holes
inside the metal case at all corners
(Diagram 5).

6
Diagram 4
Diagram 5

7
Section 3: Electrical Installation
* Power should be denied when
making all electrical connections.
Only apply power when all wire
connections have been doubled
checked for proper setup.
This section closely describes how to
power the essential components of the
system for both AC and DC installations. It
also shows how to hook up the Ring and Tip
communication wires between the Marine
Magellan Head unit and the Artion GSM
module. A basic final wiring setup for the
typical AC and DC installations can be
referenced on Appendage 1 and Appendage
2 respectively.
AC power setup
Marine Magellan
The AC plug in transformer supplies
voltage to both the Marine Magellan
Console and the battery backup supply.
The 110 VAC supply to the outlet should be
on its own breaker. If the installer must tap
into an existing outlet to get power, make
sure that the existing breaker is properly
current rated for the additional outlet. In
either case, the AC breaker must be left on
while away from boat.
Connect the two conductor wire to the
“AC”inputs of the Marine Magellan. On the
other end, connect the two wires to the
output screw terminals on the AC
transformer (Diagram 6). It is suggested
that you crimp on spade connectors to the
wire for a secure connection to the
transformer. Since the voltage source is
AC, the two connections are
interchangeable between the two inputs.
Battery Backup
The external battery backup case has
been designed to supply a constant 12 VDC
to the Artion GSM module. It simply takes
the 16 VAC input from the transformer,
inverts it to 12 VDC, and charges the
backup battery (Diagram 7). This device is
only used during AC installations.

8
Diagram 6
Diagram 7

9
DC power Setup
Marine Magellan
The Marine Magellan panel can easily
be powered from the vessels 12VDC
system. Simply get a constant voltage
source to the unit from the vessels battery
banks or domestic bus (Diagram 8). It is
suggested that the installer fuse protect the
Marine Magellan system by placing an in-
line 1 amp fuse on the Positive input wire
(not supplied).
Marine Magellan
Internal Battery Backup
The Marine Magellan uses its own
backup battery pack to provide power during
a power loss. This is not to be confused
with the Artion Battery Backup. A 7.2Vdc
1.8Ah NiMH (Nickel Metal Hydride)
rechargeable battery pack is included with
the Marine Magellan console. Connect as
shown in Diagram 9.
Artion GSM Module
The Artion GSM module simply needs a
constant 12 VDC to operate
(Diagram 10). In AC installations this power
comes from the battery backup case. In DC
installations, this power comes from the
primary domestic source.
Communication Lines
Marine Magellan to Artion
With the power establish for all the
devices, it is now time to hook up the
communication wire between the Marine
Magellan and the Artion GSM Module.
Simply connect the “Line Out”of the Artion
GSM module to the “Line In”of the Marine
Magellan. The “Line Out”of the Artion has a
tip “T”and ring “R”. The general rule when
hooking up this line is red goes to ring and
green goes to tip. There are two options for
connecting to the “Line in”of the Marine
Magellan. The first option is a line plug in
connection through an RJ-11 (Diagram 11).
The second option is a direct connection to
the “Ring”and “Tip”(Diagram 12).

10
Diagram 8
Diagram 9