Paramount Fitness SwingJet User manual

1. NEW SWING JET
•The swing jet comes packed with the cover
off.
•Push the nozzle up and look and feel for
the raised area on the side of the colored
nozzle that is in the center of the cream
colored Cam. (Fig 1). The nozzle jet open-
ing is 180 degrees opposite that raised
area. Push the nozzle shaft up and down
until the nozzle jet is either all the way right
or all the way left so when you are doing
the next two steps you are aware of which
direction it is going to travel when rotating.
•There are three notches in the cream col-
ored cam above the raised area (Fig 1).
These cam notches are in a straight line
with the cam notches on the opposite side
of the raised area. The jet opening of the
nozzle goes back and forth covering the
90 degree arc formed by the three ratchet
positions as the nozzle extends and retracts
when cycled.
•Put one wrap minimum of Teflon tape on
the threads to make the nozzle threads not
seize up over time, and thread the swing
jet in the return fitting tight, using the swing
jet installation and removal tool. It should
be tight enough so it can not be turned by
hand. Hand tighten only, NEVER USE A
WRENCH DIRECTLY ON THE SWING JET.
ALWAYS REMOVE THE COVER AND USE
THE TOOL (Fig 2 & 3) (AVAILABLE FROM
PARAMOUNT 005-721-4541-00) TO COV-
ER THE SWING JET RETAINER BEFORE
USING A WRENCH TO REMOVE THE
SWINGJET.
www.1Paramount.com 1.800.621.5886
INSTALLATION GUIDE:
SWINGJET
FIG. 1
NOTCHES
RAISED AREA
NOZZLE
SWINGJET TOOL
FIG. 2
TO REMOVE
RETAINER
FIG. 3

•Grasp the cream colored cam and turn it
either way to aim the nozzle jet to clean the
desired area. Remember the nozzle is going
to ratchet right or left depending on which of
the two side notches you placed the pins in.
(Fig 1)
•Once in position find the clip on the outside
ring of the nozzle retainer (Fig 4) and place
the hole in the cover so it is just to the coun-
ter clock wise side of the retainer clip (Fig 4).
Line up the notches on the cover with the
locking cams on the nozzle retainer. Push
the cover on to the retainer and rotate clock-
wise until the clip snaps in the hole (Fig 4).
Do not force the cover on when not in posi-
tion. It will be difficult to remove.
2. ADJUSTING A SWINGJET WHEN IT IS
THREADED IN PLACE
•Turn the pump on so the Swing Jet is on. If
the Swing Jet is on a water valve circuit, wait
for the Swing Jet to come on, and pause the
water valve.
•Place the swing jet tool (Fig 2) provided with
the unit (part # 005-721-4541-00) over the
cover with the spring loaded key over the
hole on the side of the cover of the swing jet
(Fig 5 &6). Leaving the key in place, while
pushing down on the button key rotate the
cover counter clockwise until it stops. Do not
remove the key. The extended nozzle should
now be able to be rotated to the desired posi-
tion. If the nozzle won’t easily rotate remove
the key and very slightly move the cover
counter clock wise until the nozzle will rotate.
Once the nozzle is set to the correct position,
remove the key and rotate the cover clock
wise to re-lock the cover in place.
· Cycle the Swing Jet by turning the pump off
and on to make sure you have set it in the
desired position.
INSTALLATION GUIDE:
SWINGJET (CONTINUED)
www.1Paramount.com 1.800.621.5886
U.S. Patents 7,578,010 7,481,377 6,899,285 004-027-8805-00 REV121310
FIG. 6
TO REMOVE
COVER
FIG. 5
KEY HOLE
FIG. 4
KEY HOLE
CLIP ON NOZZLE
RETAINER