Parker 71-213 Series User manual

22-100
MULTI
BLOCK
22-100
MULTIBLOCK
24-225-6
FHCS
24-225-6
FHCS
PANEL
SHOULD BE INSTALLED
IN "FLUSH
MOUNT" ORIENTATION
MULTIBLOCK
ORIENTATION
Assembly Instructions
71-213-xx & 71-223-xx
Mobile Day by the Hour Display Kits
Contact Information:
Parker Hannin Corporation
Electromechanical Automation Division
email [e-mail]
www.parker.com/ips
Two Locations to Serve You:
135 Quadral Drive
Wadsworth, OH 44281
Phone [phone]
Fax [phone]
5500 Business Park Drive
Rohnert Park, CA 94928
Phone [phone]
Fax [phone]
Recommendations:
Time to assemble: 1-2 hours
Assembly area: 10’ x 10’ or larger open floor space.
To prevent scratching, use cardboard or other protective
underlayment.
Required Tools:
• 4 mm hex wrench
• 5 mm hex wrench
• 6 mm hex wrench (ball end)
• Phillips screwdriver
• Flat head screwdriver
• Rubber mallet
Part Number: 70-105
Display Board
Size (ft)
H x W Display Board Material
Kit
Part Number
3 x 3
Clear Poly Board 71-213-WK
Black Trespa Board 71-213-PK
No Board 71-213-NK
3 x 3
Clear Poly Board 71-223-WK
Black Trespa Board 71-223-PK
No Board 71-223-NK
71-213-xx with
Andon Post Option
71-223-xx

Parker Hannifin Corporation • Electromechanical Automation Division
Assembly Instructions for 71-213-xx & 71-223-xx Kits:
Parts Beam Sets
Qty Beam # / Length
Part
Number Description
1#3 / 834.39 mm 10-540 PFL 40 x 80 Std CLR
1#1A / 867.40 mm *
10-540 PFL 40 x 40 Light CLR
1#1B / 867.40 mm
2#2 / 711.20 mm
8#4 / 127.00 mm *
* Qty eight 7 mm access holes shown in illustration used for 71-113-xx only
Note beams #1 and #5 are used for 71-213-xx only. Beam #s
refer to assembly instructions.
Beam #2
787.40 mm
*M8 Tapped End
•7 mm Access Hole
Beam #4
609.60 mm
Beam #5
127.00 mm
*
*
**
Beam #3
1437.03 mm
*
Beam #1
867.40 mm
•••••
•
••
•••
Qty
Part
Number Description
618-813 End Cap, 40 x 40
12/4* 20-002 Standard Fastening Set, 40S
420-102 Gusset Bracket, 80 x 40
24 20-058 Standard T-Nut, M8, 40S
421-310S Total Lock, Swivel Caster
3” King Pin
822-100 Multiblock 40, M6
24 24-118-8 BHCS, M8X18
424-120-10 BHCS, M10 X 1.5 x 20 mm
824-225-6 FHCS, M6X25
424-707-10 Lock Washer M10
126-790-6
26-410-6
28” x 31” Clear Poly Board for
Easel Pad
28” x 31” Black Trespa Board
for Easel Pad
427-002-M10 Base Plate 80 x 40, M10
1
70-000-XX
70-000-XX
70-000-XX
70-000-XX
70-000-XX
70-000-XX
71-213-PK Label Kit
71-213-BK Label Kit
71-213-NK Label Kit
71-223-PK Label Kit
71-223-BK Label Kit
71-223-NK Label Kit
* 12 with 71-213-xx; 4 with 71-223

800.333.4932 • www.parker.com/ips
Assembly Instructions
Step 1 (For 71-213 only)
At eight locations marked
1A, connect the Andon
posts (Beams #5) to top
frame member (Beam #1)
using Standard Fastening
Sets (20-002) and 24-118-8
BHCS fasteners.
A. Insert 24-118-8 BHCS
fasteners through hole in 20-
002 fastening set
B. Slide all 8 fasteners into the top slot of Beam #1 and position
to align with the center-most 7 mm access holes
C. Use M5 hex wrench through the bottom access holes to
tighten the 24-118-8 fasteners into the #4 beams. Firmly
secure all beam sections. DO NOT OVERTIGHTEN
Step 2 (For all units)
At six locations marked 2, join Beams #1, #2, #3 and
Beams #4 using Standard Fastening Sets (20-002).
A. Slide fasteners into the slot of the top and bottom frame
members and position to align with access holes
C. Use M5 hex wrench through access holes to tighten the
fasteners. Firmly secure all beam sections.
DO NOT OVERTIGHTEN
D. Insert 18-813 end caps on exposed beam ends.
20-002
STANDARD FASTENER
Beam #5 (8x) for
71-213-xx only
1A
1A
1A
1A
1A
1A
1A
1A
2
2
2
2
5
5
5
5
5
5
5
5
3
3
3
4
3
4
4
2
2
Beam #2
Beam #1
Beam #3
Beam #3
Beam #4
Beam #4

© 2015 Parker Hannin Corporation Parker Hannin Corporation
Electromechanical Automation Div.
135 Quadral Drive
Wadsworth, OH 44281 USA
Tel: [phone] or 330-335-6740
Fax: [phone]
5500 Business Park Drive
Rohnert Park, CA 94928
Tel: [phone]
Fax: [phone]
Email: [e-mail] or [e-mail]
Part Number: 70-105
Print Date 6.15.15
Step 4
At eight locations of display frame, use 22-100
Multiblock fasteners to attach the display panel
to the frame.
A. Insert multiblocks into T-slot and rotate 90° clockwise
B. Place panel into position and verify alignment of
multiblocks with panel holes.
C. Insert 24-2225-6 screws though panel holes and into
multiblocks to secure panel.
22-100
MULTIBLOCK
22-100
MULTIBLOCK
24-225-6
FHCS
24-225-6
FHCS
PANEL SHOULD BE INSTALLED
IN "FLUSH MOUNT" ORIENTATION
MULTIBLOCK
ORIENTATION
Assembly Instructions for 71-213-xx & 71-223-xx Kits:
Step 2. At 4 locations marked 2, attach
gussets to connect Beams #1 and #4
(4) 20-058 T-Nuts
Place T-Nuts into slot and
roll into position as shown
(1) 20-102 Gusset
(4) 24-118-8 BHCS
Step 3. At 4 locations marked 3, attach
caster assemblies to Beams #7
(2) 20-058 T-Nuts
(1) 18-813 End Cap
(1) 27-002 Base Plate
(1) 21-310S Caster
(1) 24-707-10 Lock Washer
(1) 24-120-10 BHCS
(2) 24-114-8 BHCS