Pin Signal/Function Pin Signal/Function
1 GND 7 WAKE-UP
2 CAN1_L 8 CAN4_H
3 CAN2_L 9 CAN3_H
4 CAN3_L 10 CAN2_H
5 CAN4_L 11 CAN1_H
6IGNITION_INPUT 12 +VBATT (SUPPLY)
Pro Display 12
Dashboard or panel assembly
Installation
296,60
R2 ±0,50 (4x)
195,10
Recommended RAM mount accessories:
For 12-inch display, Parker recommends to use RAM round plate with 1,5” ball (2 x RAM-202) together with RAM
double socket arm (RAM-201).
Guidelines for dashboard/panel mounting:
A. Use gasket between device ange and panel cutout edges to
ensure adequate sealing, and prevent device to vibrate.
B. Attach electrical connections to the device before closing the
cutout with the device. Take into account the device mounting
depth 45,9 mm and required space for connectors’ installation on
the back of the display.
C. Place the device to panel cutout, push the device lightly and
ensure its stability to panel cutout edge.
D. Consider suitable anchor points for a possible bracket on the
back of the panel, to evenly position the device.
E. Fasten mounting bracket with screws from the backside of the
assembly panel by using 4 mounting points of the device.
• Use only existing mounting points of the device to x the unit.
• The mounting points are blind holes with a maximum thread
depth of 7,5 mm.
• If the spacer is not used the screw length should be 6 mm.
Note! Longer screws may damage the device when tightened
• Apply tightening torque 2,7 Nm.
Torque 2,7 Nm
Pro Display 12 can be assembled to the vehicle dashboard, to the separate panel in vehicle cabin
or for example to cabinet door in installations where exists separate electrication cabinet. Currently
Pro Display 12 has no dedicated panel mounting kits available due to the fact that the panel
thickness can vary depending on assembly surface and customer needs.
2
3
4
5
67
8
9
11
C2
6
5
4
3
2
Pin Signal/Function Pin Signal/Function
1 RS232_RXD_2 7 HSIDE_OUT
2 RS232_TXD_2 8 AUDIO_LINE_IN_OUT_R1
3 GND 9 AUDIO_LINE_IN_OUT_L1
4 AUDIO_LINE_OUT_L 10 MIC_N
5 AUDIO_LINE_OUT_R 11 MIC_P
6GND 12 MIC_BIAS
Mating connector: Housing, Deutsch DTM06-12SA;
Terminals, Deutsch 1062-20-0222;
Sealing plugs, Deutsch 0413-204-2005
Recommended cable: 0,75 - 1,0 mm2 (AWG 18)
Mating connector: Housing, Deutsch DTM06-12SB;
Terminals, Deutsch 1062-20-0222;
Sealing plugs, Deutsch 0413-204-2005
Recommended cable: 0,75 - 1,0 mm2 (AWG 18)
Pin Signal/Function
1 5V_USB1
2 USB1-
3 USB1+
4 GND
5 SHIELD
Mating connector:
M12-4pin male, D-coded (available
from several manufacturers).
Pin Signal/Function
1 5V_USB0
2 USB0-
3 USB0+
4 GND
5 SHIELD
Mating connector:
M12-4pin male, D-coded (available
from several manufacturers).
Pin Signal/Function
1 CVBS_IN1
2 CVBS_IN4
3 CVBS_IN3
4 CVBS_IN2
5 GND
6 SHIELD
Mating connector:
M12-5pin male, A-coded (available
from several manufacturers).
Pin Signal/Function
1 TX+
2 RX+
3 TX-
4 RX-
5 SHIELD
Mating connector:
M12-4pin male, D-coded (available
from several manufacturers).
Pro Display 12Wiring diagram Installation
Pin Signal/Function
1 GND
2 AERIAL
Mating connector:
SMA male (available from several
manufacturers).
Radio Antenna Connection:
CAUTION
The torque recommendation need
to be followed.
Mounting Options
ANT
Mounting with RAM Mount
Torque 2,7 Nm
RAM round plate with ball
Recommended: C size 1,5” rubber
ball connected to a 2,5” diameter
round plate.
RAM double socket arm
RAM round plate with ball
C4
C3
C1
ANT
C2
C5
C6
Mounting with RAM ball allows
adjustment of the display’s position
and angle.
To fasten the RAM 2,5” round plate,
use 4 x M4 screws of class 8.8 or
higher. It is preferred to use Hex
Socket Cap Screw ISO 4762 / DIN
912 or Pan Head Torx Machine
Screw ISO 14583 TX / DIN 7985
type.
1 Default mode for these signals is Audio Line Input
CAUTION
The mounting points are blind holes
with a maximum thread depth
of 7,5 mm. Longer screws may
damage the device when tightened.
Mounting points (4 pieces)
