Paxton 690-333-US User manual

Ins-30037-US Hands free keycard for Net2
08/17/2011
Battery replacement
The keycard has been designed with features to maximise battery life. These include a two second timeout once
access has been granted and the prevention of repeated access requests whilst the keyfob remains in same reader
eld. Heavy usage or leaving the keycard within range of a reader will reduce battery life.
Remove the screw on the back of the card. Open the case by inserting a at head screw driver in the slot at the
bottom of the card and gently prying the case open. Remove the circuit board and replace the batteries. Replace
the circuit board, casing cover, screw and label.
The keycard can store up to 60 doors, thirty for each button.
The system comprises of a Hands Free Interface, a compatible reader (see specication table) and hands free
keycards or keyfobs. The system operates by using the eld being transmitted by the P series reader to wake up
the token. This then communicates with the interface which contains a long range receiver.
The keycard increases this eective read range to typically 5 yds (maximum 50 yds). This is achieved by
activating the system manually instead of using the reader eld (maximum 8 feet)
Keycards also include a standard EM4100 proximity ID chip and can therefore be presented to any compatible
proximity reader whether they are using the Hands Free interface or not.
What is Hands Free?
The hands free interface has a pair of switches labelled SW2. Select either switch 1 or 2 to set which button the
interface will respond to and then power cycle the interface to store this setting.
Interface Settings
To enable the buttons, the keycard must rst be presented to the P series reader and then used in hands free
mode. The keycard stores the details of this interface and can then activate the door using a button.
It can still be used in normal hands free mode and also in local passive mode with other standard readers.
Paxton
SW2
1
Hands free interface
Switch settings

3
1
2
CR2430
1
2
Specications
33/8in
21/8in
3/8in
EM4100 125 kHz
2.4 GHz
0 °C (32 °F) 55 °C (131 °F)
Specications
Carrier frequency
Operating temperature
Environment
Dimensions
Min Max
Width
Height
Depth
System Specication
Token type

[phone]
[email protected]
paxton.support
[phone]
paxton.benelux.support
[email protected]
[phone]
paxton.support
[email protected]
[phone]
paxton.gmbh.support
[email protected]
[phone]
paxton.support
[email protected]
8000 3570 3783
paxton.support
[email protected]
[phone]
[email protected]
paxton.support
877.438.7298
usapaxton.support
[email protected]
[phone]
paxton.soporte
[email protected]
[phone]
paxton.soporte
[email protected]
[phone]
paxton.benelux.support
[email protected]
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
1 x CR2430
P38 3 ft
P50 4 ft
P75 5 ft
P200 8 ft
6 ft
16 ft
Electrical
P200E metal mount
Read range with hands free token
Typical Battery Life
Battery Type
With button - all readers > 5 yds
5 years
Long range reader
Handsfree Cards and Fobs have been tested to give a realistic representation of read ranges users can expect to
see when taking into consideration dierent environmental factors.
P38 0.20 0.10 0.00 0.40 0.30 0.00 20-25
P50 0.30 0.20 0.15 0.50 0.40 0.30 20-25
P75 0.50 0.30 0.30 0.80 0.50 0.40 20-25
P200 1.30 0.80 0.40 1.80 1.00 0.50 20-25
P200M 1.30 0.80 0.40 1.80 1.00 0.50 20-25
5.00 3.00 2.00 5.00 1.50 1.00 20-25
Results shown in meters only
P Series readers Handsfree Fob
On lanyard In pocket In pocket
In pocket
with GSM
In pocket
with GSM
Button Control:
Handsfree Card
Handsfree Card
On lanyard

© Paxton Ltd 1.0.6
Made in the UK