Paxton Ins-30150-US User manual

Due to the regional and local requirements for specic cell phone coverage you will need to purchase the SIM
card required for your area. For example, Verizon or AT&T. Most electronic stores, such as Best Buy and Fry's
Electronics, carry SIM cards.
WHAT YOU NEED TO LOOK FOR:
1. SIM Card that works for UNLOCKED phones.
2. SIM Card Service that allows automatic charging.
3. The service with lowest monthly payment because the unit does not extract any minutes o the plan.
The best plan is the fewest minutes and the most months.
The SIM Card Service will provide the Phone number that you will call to access the Caller ID reader.
Connection to the
Net2 ACU reader port
0V
Data/D0
Clock/D1
12V
LED
LED
LED
12V DC
0V
Data/D0
Clock/D1
12V
LED
LED
LED
ACU
Paxton Caller ID
(Optional)
SIM card not supplied
Antenna
Ins-30150-US Net2 Caller ID/GSM Access Reader
Technical Support
Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)
1.800.672.7298 [email protected]
Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/
Paxton
05/19/2011
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Changes or modications not
expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.

10V DC 14V DC
500 mA
50 feet
-20°C (-4°F) 55°C (131°F)
7 7/8in 7 7/8in 3 in
Specications
Operating temperature
Electrical
Environment
Dimensions
Min Max
Width Height Depth
Cable length between ACU and Caller ID reader
Waterproof
Additional power supply required
No
No
Voltage - Reader module
Current - Reader module
Set the reader operating mode in the Net2 software to 'Paxton Reader' and the Operating mode to 'Token only'
Enter the last 8 digits of the phone number into the Net2 user record as the token number.
A phone number of 1 800 672 7298 becomes 06727298 as a Net2 token.
Adding the user's phone to a Net2 user record
Features
Carrier frequency Quad band GSM
Phones supported Caller ID enabled
LED indications
Power - 12v DC supply OK
Network - Connected to the Mobile phone network
Activity - The reader is receiving data from a mobile phone
Installation
Insert the SIM card in its holder at the top right of the unit.
A drilling template for the plastic housing is available at < http://paxton.info/1715 >
If the device is to be installed where the mobile signal may be low, the antenna should be installed externally.
Secure the antenna by:
1. Internal - Remove the peel o paper from the adhesive strip and x within the enclosure.
2. Externally - Disconnect the SMA screw connection and route the cable through any of the cabinet push-out plugs
and x to a smooth surface.
Wire the Caller ID reader color for color to a Net2 ACU reader port within a maximum cable length of 50 feet.
Belden 9540 or General Cable C0745A is recommended for all data cable wiring.
If a token reader is also installed, it is connected to the Caller ID's own reader port within a maximum cable length
to the Net2 ACU of 300 feet.
Power up the unit and conrm that the Power LED comes on. The Network LED will come on within a few minutes
once the unit is active on its GSM network.

Due to the regional and local requirements for specic cell phone coverage you will need to purchase the SIM
card required for your area. For example, Verizon or AT&T. Most electronic stores, such as Best Buy and Fry's
Electronics, carry SIM cards.
WHAT YOU NEED TO LOOK FOR:
1. SIM Card that works for UNLOCKED phones.
2. SIM Card Service that allows automatic charging.
3. The service with lowest monthly payment because the unit does not extract any minutes o the plan.
The best plan is the fewest minutes and the most months.
The SIM Card Service will provide the Phone number that you will call to access the Caller ID reader.
Connection to the
Net2 ACU reader port
0V
Data/D0
Clock/D1
12V
LED
LED
LED
12V DC
0V
Data/D0
Clock/D1
12V
LED
LED
LED
ACU
Paxton Caller ID
(Optional)
SIM card not supplied
Antenna
Ins-30150-US Net2 Caller ID/GSM Access Reader
Technical Support
Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)
1.800.672.7298 [email protected]
Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/
Paxton
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Changes or modications not
expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.

10V DC 14V DC
500 mA
50 feet
-20°C (-4°F) 55°C (131°F)
7 7/8in 7 7/8in 3 in
Specications
Operating temperature
Electrical
Environment
Dimensions
Min Max
Width Height Depth
Cable length between ACU and Caller ID reader
Waterproof
Additional power supply required
No
No
Voltage - Reader module
Current - Reader module
Set the reader operating mode in the Net2 software to 'Paxton Reader' and the Operating mode to 'Token only'
Enter the last 8 digits of the phone number into the Net2 user record as the token number.
A phone number of 1 800 672 7298 becomes 06727298 as a Net2 token.
Adding the user's phone to a Net2 user record
Features
Carrier frequency Quad band GSM
Phones supported Caller ID enabled
LED indications
Power - 12v DC supply OK
Network - Connected to the Mobile phone network
Activity - The reader is receiving data from a mobile phone
Installation
Insert the SIM card in its holder at the top right of the unit.
A drilling template for the plastic housing is available at < http://paxton.info/1715 >
If the device is to be installed where the mobile signal may be low, the antenna should be installed externally.
Secure the antenna by:
1. Internal - Remove the peel o paper from the adhesive strip and x within the enclosure.
2. Externally - Disconnect the SMA screw connection and route the cable through any of the cabinet push-out plugs
and x to a smooth surface.
Wire the Caller ID reader color for color to a Net2 ACU reader port within a maximum cable length of 50 feet.
Belden 9540 or General Cable C0745A is recommended for all data cable wiring.
If a token reader is also installed, it is connected to the Caller ID's own reader port within a maximum cable length
to the Net2 ACU of 300 feet.
Power up the unit and conrm that the Power LED comes on. The Network LED will come on within a few minutes
once the unit is active on its GSM network.