Paxton TOUCHLOCK K Series User manual

10/26/2010
Ins-30013-US TOUCHLOCK K series compact keypad
Fitting
Keypad bezels
Additional bezels are available in black, white, grey, blue and silver. Registered installers can order these free of
charge by logging onto the secure installer extranet: https://extranet.paxton-access.co.uk/index.asp. If you
are not a registered installer please call us on: 877.438.7298 for more information.
Technical Support
Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)
Saturday from 04:00 AM - 08:00 AM (EST)
1.800.672.PAXT [email protected]
Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/
FCC Compliance
Class B digital devices.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Class A digital devices.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Paxton

Bell
Exit button
(push to make)
Electric release
12V DC power
supply
Wire outputs +12V DC
0V
Lock 12V
Lock 0V
Exit input
Exit 0V
12 3
456
789
0 #
*

12V DC release current rating must be less than 1A.
Wiring
1. Power down the system.
2. Power the system up whilst pressing and holding 3.
3. The LED's will ash and the unit will beep 3 times a second.
4. Go to the programming guide. - Initialising a new system.
Full System Reset
Bell 12V
Bell 0V
K75 Screw connector option
The unit should be mounted in conjunction with
an electrical backbox to achieve the required
clearance for the connector.
If an adaptor plate (310-750-US) is tted, the
mountings on the backbox can also be used.
Exit
0V
0V
0V
+12V
+12V
+12V
0V

This box can be used to write down the Programming Code for future reference.
Ensure that this information is stored in a secure place.
X
Single or multiple
codes
Silent operation
20 wrong keystrokes
= 60 second lockout
Door open time
(seconds)
Change
Programming Code
Exit button
Set a
user code
Data Reset (except
Programming code)
OR
One code only Multiple codes allowed
Silent
Beep on
OFF ON
Enter time in seconds
(default = 07, max = 60)
Open door for
time in option 5
Toggle door open
until pressed again or
toggle code entered
Enter user code
4-8 digits
Re-enter
user code
Enter 6 digit
Programming
Code
= Delete
= Normal
= Toggle
= Duress
Enter 6 digit
Programming
Code
Re-enter 6 digit
Programming
Code
6
OR
OR
X
OR
2
4
6
8
OR
OR
OR
Lock wire setting Fail locked Fail open
OR
2
2
2
2
2
2
1
3
4
7
5
6
9
8
6
6
6
6
9
START - Enter the 6 digit Programming Code and hold down a function key
for 3 seconds. - The unit beeps and the LED ashes faster.
Continue the key sequence to set the option - The keypad returns to operating mode.
= Hold down for 3 secs
Choose a 6 digit Programming Code and load this into the unit as follows:
IMPORTANT: Do not set the Programming Code to 123456
The default user code is 1234 - the programming code must not include 1234 in the same order.
The door lock will release after 1234 and ignore any remaining numbers.
The factory User Code is now set to 1234
Initialising a new system
You can now set up the user codes and features using the programming chart.
Example: - Setting a user code to unlock the door under Normal condition
Enter user code
4-8 digits
Re-enter
user code 4
8
Enter 6 digit
Programming
Code
Hold for 3 secs
The unit will beep and the LED ashes faster
Enter 6 digit
Programming
Code
Re-enter 6 digit
Programming
Code
Normal

1 50
4 digits 8 digits
1 sec 60 secs
11V DC 14V DC
170 mA
1 A
12V DC
-20 °C (-4 °F) +55 °C (+131 °F)
IPX7
K38 1 1/2in 3 in 1/2in
K50 2 in 4 in 5/8in
K75 3 in 5 1/2in 5/8in
Voltage
Switchable current
Specications
Operating temperature
Electrical
Environment
Dimensions
Min Max
Width Height Depth
Current
Outdoor Use
Features
Number of Codes
Code length
Door open time
Silent operation
Can be used with fail OPEN locks
Can be used with fail CLOSED locks
Exit button input
Door Contact input
Alarm/bell output voltage
Waterproof
Backlight
Cable length
Min Max
Min Max
Yes
Yes
Yes
Yes
No
3 yards
Yes
1 - Can I use a fail open release (e.g. Maglock)?
QThe lock wires from a compact keypad provide 12V DC to the electric lock. By default, the compact is set to operate with a fail
Qlocked release - providing 12V on the lock wires when a valid entry is made. To use a fail open release, the lock wire setting
Qneeds to be changed (Program option 1)
2 - Can I put a relay across the lock wire output?
QYes - All compact systems have been designed to drive relays.
3 - Integration with an entry phone system.
QThe output from the entry phone system is used to simulate an exit button for the Paxton equipment. No voltage should be
Qapplied to the exit input wires (Blue / Mauve) of a compact unit. Most phone systems will provide a powered pair to release the
Qdoor lock; this voltage must be used to drive an independent relay. The relay contacts must be 'normally open going closed' to
Qmimic a 'push to make' exit button. Only a voltage free output pair can be connected directly to the exit input wires.
4 - What are the keypad code types used for?
QNormal - Releases the door for the time period set in Option 5 ( 7 secs default)
QToggle - Releases the lock until the code is entered for a second time.
QDuress - Releases the lock (as in Normal) but also energizes the bell output for 30 seconds.
QDelete - Used to remove a specic code that has already been entered in Multiple mode.
5 - Connecting a compact with another control unit.
QThis cannot be done. Paxton Compact systems have the control electronics built in and no direct data output is provided.
QThe Switch2 and Net2 system use a dierent type of data input.
QNote: The compact system will control the door unit on its own.
6- Read in and read out on one door.
QYou cannot wire two compact systems in parallel to a common lock as this may result in damage to your system. They will both
Qpower the door lock independently and will not oer single point control. We recommend using one Switch2 controller with two
Qcompatible keypads or readers.
Here is the list of topics about this product that receive the most technical support inquiries.
We list them here to help you speed up the installation and trouble shooting process.
Vandal resistance Low