baby&child AVA User manual

1pc
Ava Cabinet [1]
RESTORATION HARDWARE
Page 1 of 3
AVA CHANGING TABLE
ASSEMBLY INSTRUCTIONS
12pcs
Ava changing table topper [2]
2pcs
Steel connecting plates [3]
Instructions to fit the Ava Changing Table Topper to the Top of The Ava Cabinet.
1. Locate 4 pre-drilled holes on the top back side of the Ava Cabinet and align with 4 pre-drilled holes in Ava Topper.
2. Screw 2 steel connecting plates into the pre-drilled holes using 8 screws provided.
3. Follow instructions Anti-Tip kit next page to secure this unit to the wall.
1pc
Parts Included :
25mm
45mm
Product side mounting screws [4]
4pcs
Stud mounting screws [6]
Plastic mounting bracket [5]
2pcsNylon zip tie
4pcs
WARNING:
FALL HAZARD-To prevent death or serious injury from falls, always keep child within arms reach. NEVER LEAVE CHILD
UNATTENDED and always use restraining system.
This changing system is intended for using with children weighing up to 30 lbs.
AVA CHANGING TABLE TOPPER will be used with AVA CABINET, with size 40"W x 18"D x 35"H. Cushion Pad size is
32"W x 16"D x 4"H

WARNING:
FALL HARZARD-To prevent death or serious injury from falls, always keep child within arms reach. NEVER LEAVE CHILD
UNATTENDED and always use restraining system.
This changing system is intended to use with children weighing up to 30 lbs.
The warning identify specific products to attached the products to AVA CHANGING TBL TPPR AMIR will be used with AVA
CABINET AMIR with size 40"W x 18"D x 35"H
1. Locate a wall stud behind your furniture piece. Position a bracket on the stud approximately 1" below the top of the
furniture. Mark and drill pilot hole into the center of the stud with a 3/32" drill bit. Attach a bracket to the stud with the
long screws provided. (Detail A)
2. On the back of the furniture, attach a bracket to the furniture frame at the top. To do this, temporarily move the
furniture into its final position and mark the location of the wall bracket on the furniture frame. Move the furniture
away from the wall and place a bracket on the mark. Mark and drill holes for the screws with a 3/32" drill bit. Attach
the bracket to the furniture with the short screws provided. (Detail B)
3. Move the furniture into its final position, taking care to line up the wall bracket with the furniture bracket. Thread a
strap though the bracket as shown in the illustration. Tighten strap until snug. Do not over tighten. (Detail C)
4. Important: Check to be sure the wall bracket is firmly screwed into wall stud, the furniture bracket is firmly attached to
the frame, and the strap is snug.
DETAIL C
WALL
FURNITURE
5
4
4
5
Page 2 of 3 Page 3 of 3
Thank for your purchase
www.rhbabyandchild.com
RESTORATION HARDWARE RESTORATION HARDWARE
1pc
Ava Cabinet [1]
RESTORATION HARDWARE
Page 1 of 3
AVA CHANGING TABLE
ASSEMBLY INSTRUCTIONS
12pcs
Ava changing table topper [2]
2pcs
Steel connecting plates [3]
Instructions to fit the Ava Changing Table Topper to the Top of The Ava Cabinet.
1. Locate 4 pre-drilled holes on the top back side of the Ava Cabinet and align with 4 pre-drilled holes in Ava Topper.
2. Screw 2 steel connecting plates into the pre-drilled holes using 8 screws provided.
3. Follow instructions Anti-Tip kit next page to secure this unit to the wall.
1pc
Parts Included :
25mm
45mm
Product side mounting screws [4]
4pcs
Stud mounting screws [6]
Plastic mounting bracket [5]
2pcsNylon zip tie
4pcs
Instructions to fit anti-tip kit.

WARNING:
FALL HARZARD-To prevent death or serious injury from falls, always keep child within arms reach. NEVER LEAVE CHILD
UNATTENDED and always use restraining system.
This changing system is intended to use with children weighing up to 30 lbs.
The warning identify specific products to attached the products to AVA CHANGING TBL TPPR AMIR will be used with AVA
CABINET AMIR with size 40"W x 18"D x 35"H
1. Locate a wall stud behind your furniture piece. Position a bracket on the stud approximately 1" below the top of the
furniture. Mark and drill pilot hole into the center of the stud with a 3/32" drill bit. Attach a bracket to the stud with the
long screws provided. (Detail A)
2. On the back of the furniture, attach a bracket to the furniture frame at the top. To do this, temporarily move the
furniture into its final position and mark the location of the wall bracket on the furniture frame. Move the furniture
away from the wall and place a bracket on the mark. Mark and drill holes for the screws with a 3/32" drill bit. Attach
the bracket to the furniture with the short screws provided. (Detail B)
3. Move the furniture into its final position, taking care to line up the wall bracket with the furniture bracket. Thread a
strap though the bracket as shown in the illustration. Tighten strap until snug. Do not over tighten. (Detail C)
4. Important: Check to be sure the wall bracket is firmly screwed into wall stud, the furniture bracket is firmly attached to
the frame, and the strap is snug.
DETAIL C
WALL
FURNITURE
5
4
4
5
Page 2 of 3 Page 3 of 3
Thank for your purchase
www.rhbabyandchild.com
RESTORATION HARDWARE RESTORATION HARDWARE
1pc
Ava Cabinet [1]
RESTORATION HARDWARE
Page 1 of 3
AVA CHANGING TABLE
ASSEMBLY INSTRUCTIONS
12pcs
Ava changing table topper [2]
2pcs
Steel connecting plates [3]
Instructions to fit the Ava Changing Table Topper to the Top of The Ava Cabinet.
1. Locate 4 pre-drilled holes on the top back side of the Ava Cabinet and align with 4 pre-drilled holes in Ava Topper.
2. Screw 2 steel connecting plates into the pre-drilled holes using 8 screws provided.
3. Follow instructions Anti-Tip kit next page to secure this unit to the wall.
1pc
Parts Included :
25mm
45mm
Product side mounting screws [4]
4pcs
Stud mounting screws [6]
Plastic mounting bracket [5]
2pcsNylon zip tie
4pcs
Instructions to fit anti-tip kit.