Argos Canterbury 3 DR Robe User manual

Canterbury 3 DR 3 DRW MIR ROBE
Assembly Instructions - Please keep for future reference 498/1912
499/9760
483/6469
Dimensions
Width - 152.8cm
Depth - 62.7cm
Height - 202.1cm
71939 Version E Date 14/06/2016
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
max.
lbs
kg8
18
lbs
kg30
66
lbs
kg20
44
lbs
kg25
55
lbs
kg20
44

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to lay out the parts before
starting.
• During assembly, do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the use
of power drivers for
inserting screws, as
this could damage
the unit. Only use hand screw
drivers.
• The provided tip-over restraint
must be installed in order to
optimize user safety.
Safety
1

Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
Bottom / top panel (152,8 x 62.4cm) x2
Side panel L/R (198.8 x 58cm) x2
Large divider panel (198.8 x 58cm)
UC
GA
UB
T
E
Small fixed shelf
(47 x 58cm) x2
Large fixed shelf
(95.5 x 57.9cm) x2
Loose shelf
(47 x 58cm) x2
Drawer front
(48.2 x 22.1cm) x3
Small divider panel (25 x 57.8cm) IC
FA
GB
02748 Drawer back
(42.1 x 14cm) x3 00487 Right drawer side (43.5 x 14cm) x3 00486 Left drawer side
(43.5 x 14cm) x3
06294 Drawer bottom
(43.3 x 43.3cm) x3
76428 Profile side (62 x 2,5cm) x2 76431 Profile side (152 x 4cm) x2
76427 Profile side (62 x 2,5cm) x2
09789 Back panel (201.5 x 97.4cm)
09790 Back panel (201.5 x 48.9cm)
18731Frame door (169.3 x 48.2cm) x2
Door w. mirror (169.3 x 48.2cm)
CBA
D
M
N
L
H
J
W
K
2

3
Please check you have all the fittings listed below
Holder x2
Nails x3
Bracket x16
Connector bolt
(ø7x50mm) x21
Flat head screw
(ø5.8x9mm) x12
(M4x15mm) x12
Flat head screw
(ø3.5x15mm) x6
Screw (ø5 x 7mm) x16
Drawer support x6 Shelf support x8
Flat head screw
(ø6.3x27mm) x20
Floor glider x8
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Allen key x1
Drawer runner x6
Flat head screw
(ø3x12mm) x2
Drawer fastener x12
Dowel (ø5x30mm) x16
Machine screw
(M4x7mm) x12
Hinge x12
Wedges x4
Cam x8Cam bolt x8
Hinge plate x12
Screw (ø7x8mm) x24
Handle x6 Stop x6
Hanger x1
Components - Fittings
Ruler - Use this ruler to help correctly identify the screws
Tools required
Cross head screwdriver
(medium & large) wooden block
Books X6
Flathead screwdriver
(medium)
Ruler
Eye protection
(when using a
hammer or glue)
10601 11011 11042
20228
25233
26020
11229
11230 20203 23006
25215 25610
26033 26071
31513 31687
26211
26221 26232
33204 50491
96203 97642
41434 72509
01 02 03 04 05 06 07 08 09 0 100 110 120 130 140 150
01 23 45 6
63008
94009
81040
52291
25 pcs
Strap x2
Tape measure
Hammer
Big nail x18
23010
Machine screw Machine screw
(M4x23mm) x6

4
Assembly Instructions
Step 1
Step 2
Insert dowles
Insert dowels 20203
into outer holes on the
ends of panel FA +GB
Place cam 31687 into
the holes on top of small
divider panel GA .
Arrow facing the edge of
the panel. GA
FA
FA
FA
GB
GB
Attaching hanger holder
Attach holder 10601 with
flat head screw 25215 on
side panel FA and divider
panel GB .
Flat head screw
# 2215 X2 Holder # 10601 X2
Fittings you will need for this step:
Cam
# 31687 X2 Dowel # 20203 X16
Fittings you will need for this step:
4

5
Assembly Instructions
Step 3
Attaching hinge plate
Fixing each hingplate
50491 with screw
2x 26071 .
Insert machine screw
26211 in center of
hinge plate.
Fittings you will need for this step:
Hinge
# 50491 X12 Screw # 26071 X24 Machine screw # 26211 X12
GB FA
FA
49
1
3
4
20
19
35
36
48
5

Assembly Instructions
6
Step 4 Fittings you will need for this step:
Screw
# 11230 X8
Attach screw 11230 as
shown.
FA
FA
6

Place drawer runners
1.
Extend drawer glide
41434 .
2.
Attach drawer glide at the
front of side panel FA .
Place screw 26020
through the correct hole
at the front of the drawer
glide, into the holes on
the side panel FA .
Tighten screw but do not
overtighten.
3.
Open slide until 3 holes
is visible at back of
drawer glide.
4.
Place screw 26020
through the correct holes
at the back of the drawer
glide, into the holes on
the panel FA .
Tighten screw but do not
overtighten.
5.
Attach the flat head
screw 25233 into the
correct holes of the
drawer glide, into the
side panel FA .
Tighten screw but do not
overtighten.
Repeat these 5steps for
the remaining runners.
5
Assembly Instructions
Step 5 Fittings you will need for this step: Drawer runner
# 41434 X2
Flat head screw
# 25233 X2 Flat head screw # 26020 X4
Front
Front Front
Front Front Front
1.
FA
FA
2.
3.
4.
5.
x1
x1
x1
7

Assembly Instructions
6
Step 6 Fittings you will need for this step:
Screw
# 11230 X8
Drawer supporter
Attach the screw 11230
on both sides of the
large divider panel GB .
GB
Bottom
8

Assembly Instructions
Step 7 Fittings you will need for this step:
Flat head screw
# 25233 X4 Flat head screw # 26020 X8 Drawer runner # 41434 X4
Bottom
GB
GA
Place drawer runners
1.
Extend drawer glide
41434 .
2.
Attach drawer glide at
the front of small divider
panel GA .
Place screw 26020
through the correct hole
at the front of the drawer
glide, into the holes on
the small divider panel
GA .
Tighten screw but do not
overtighten.
3.
Open slide until 3 holes
is visible at back of
drawer glide.
4.
Place screw 26020
through the correct holes
at the back of the drawer
glide, into the holes on
small divider panel GA .
Tighten screw but do not
overtighten.
5.
Attach the flat head
screw 25233 into the
correct holes of the
drawer glide, into the
small divider panel GA .
Tighten screw but do not
overtighten.
Repeat these 5steps for
the remaining runners on
the other side of small
divider panel GA and
on both sides of large
divider panel GB .
Front
Front
9