PB TEEN Primo Plasma Media Base User manual

Page 1/6
www.pbteen.com
Primo Plasma Media Base
! CAUTION
•The top shelf of this stand is intended for use with: a Plasma/LCD/DLP/HD Television with a maximum screen size
of 41-45 inches and/or a weight of 100lbs OR a Tube Television with a maximum screen size of 14-16 inches and
weight of 35lbs. All other support shelves should not be loaded more than 25lbs.
•DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and weight
indicated may result in instability causing possible injury.
DO NOT REMOVE THIS LABEL
04-000076-2
PRE-ASSEMBLY:
•For your safety and ease, assembly by two adults is recommended.
•Read all instructions before beginning assembly.
•Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The shipping box
provides and ideal work surface. Do not dispose of any contents until assembly is completed to avoid accidentally
discarding small parts or hardware.
•Do not use power drill as it may cause cracking.
PARTS INCLUDED:
A- Media Base (1pc)
B- Large Adjustable Shelf (1pc)
C- Small Adjustable Shelf (2pcs)
HARDWARE INCLUDED:
D- Screw (3/16” x 1-1/4) (2pcs)
E- Shelf Support (12pcs)
F- Knob (2pcs)
TOOLS REQUIRED (but not included):
•Phillips Head Screwdriver
A
B
C
C

Page 2/6
www.pbteen.com
Figure 1
Figure 3
Figure 2
ASSEMBLY INSTRUCTIONS:
1. Attach the Knob (F) to the door by placing the Knob (F) over the pre-drilled hole on the door front, insert the Screw
(D) from door interior; tighten using a Phillips Head Screwdriver as shown below.
2. Insert the Shelf Supports (E) into the pre-drilled holes located on the interior of the Media base (A) as shown in
Figure 2. Carefully place the Adjustable Shelves (B and C) onto the shelf support as shown in Figure 3.
FD
A
A
E
A
B
C

Page 3/6
www.pbteen.com
Figure 4
3. If the media base does not sit level, loosen or tighten the adjustable levelers underneath each piece.
CARE INSTRUCTIONS:
•Dust often using a soft, dry cloth.
•Do not use glass cleaner, abrasives, wax or household cleaners on wood.
•Check fasteners periodically for tightness. Do not over tighten; this may cause distortion or breakage.

Page 4/6
www.pbteen.com
Primo Plasma Media Hutch
! CAUTION
•The top shelf of this stand is intended for use with: a Plasma/LCD/DLP/HD Television with a maximum screen size
of 41-45 inches and/or a weight of 100lbs OR a Tube Television with a maximum screen size of 36-40 inches and
weight of 240lbs. All other support shelves should not be loaded more than 25lbs.
•DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and weight
indicated may result in instability causing possible injury.
DO NOT REMOVE THIS LABEL
04-000076-2
PRE-ASSEMBLY:
•For your safety and ease, assembly by two adults is recommended.
•Read all instructions before beginning assembly.
•Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The shipping box
provides and ideal work surface. Do not dispose of any contents until assembly is completed to avoid accidentally
discarding small parts or hardware.
PARTS INCLUDED:
A- Media Base (1pc)
B- Large Adjustable Shelf (1pc)
C- Small Adjustable Shelf (2)
D- Media Hutch (1pc)
HARDWARE INCLUDED:
E- Bolt (5/16” x 2-1/2”) (4pcs) H- Drill Bit (10mm) (1pc)
F- Washer (5/16) (4pcs) I- Wood Block (1pc)
G- Block Washer (5/16) (4pcs) K- Allen Key (4mm) (1pc)
A
B C
C
D

Page 5/6
www.pbteen.com
Figure 2
TOOLS REQUIRED (but not included):
•Power Drill
ASSEMBLY INSTRUCTIONS:
1. Locate the two partially drilled holes on the interior top panel of the Media Base (A). Using a Power Drill with Drill
Bit (H) bore through the partially-drilled holes holding Wood Block (I) on exterior of the top panel of the hole being
drilled to prevent any breakage or damage when drilling. Please Note: Keep hands away from moving drill bit.
Repeat for other side.
2. With the assistant from second adult, align the pre-drilled holes on bottom of the Media Hutch (D) with the holes
previously drilled on the top of Media Base (A). Insert the Washer (F), Block Washer (G) and Bolt (E ) into the pre-
drilled holes from the interior of the Media Base (A) as shown below; tighten using the Allen Key (K).
.
A
D
E
F
G
Figure 1
A
H
I

Page 6/6
www.pbteen.com
Figure 4
3. Carefully place the Adjustable Shelves (B and C) onto the shelf support as shown below.
4. Adjust the adjustable levelers on the bottom of the legs by loosening or tightening them so the Media base sits
evenly on floor as shown below.
5. As a safety precaution, please follow the instruction enclosed to secure the Media unit to the wall using tipping-
restraint included.
CARE INSTRUCTIONS:
•Dust often using a soft, dry cloth.
•Do not use glass cleaner, abrasives, wax or household cleaners on wood.
•Check fasteners periodically for tightness. Do not over tighten; this may cause distortion or breakage.
B
CA
D
Figure 3