Wren TOWER UNIT User manual

2070 x 600
600 + 450 Appliance
2250 x 600 Tall
600 + 450 Appliance
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide

BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
DRAWER
COVER
CAP
x2
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER
FRONT
FIXING
x 2
Deep Drawer (Packed Separately)
Fitting Pack Contents
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(N) x1
Door Buer
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
METAL BACK PANEL
x 1
DRAWER
BASE
x 1
DRAWER RUNNER
x 1 Right Hand
FRONTAL
(Supplied separately)
DRAWER RUNNER
x 1 Left Hand
GALLERY
RAIL
x 2
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.inddPage 1
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Drawer Assembly

R
R
R
R
Q
Step 1.
Secure drawer base to drawer side using 4 x 16mm drawer
runner screws (J) in holes provided.
Seat the edge of drawer base tight into corner of casing, as
shown.
The decorative face of drawer base
to be positioned as shown.
J
J
J
J
J
J
Drawer
base
Fixing
clip
& (Q)
Fixing
clip
& (Q)
Drawer
side
Drawer side
xing clip
Q
2
1
J
J
Step 2.
Clip on metal back panel
to drawer base & drawer
sides.
Y & L Y & L
Step 5.
Draw Adjustment
Screw point 1as shown to
adjust drawer frontal
right & left.
Step 6.
Fit Gallery Rail into the
top corners of Metal
Back-panel.
Locate front end of the
Gallery Rail into the
opening of the gallery
Head, which is secured to
the frontal as shown
Step 7.
Fit Drawer Cover Caps
over drawer side adjustment.
Drawer
Cover Cap
Drawer Frontal
Adjustment
Screw point 2a
as shown to adjust
drawer frontal up & down.
Tighten 2b
once in position.
Releasing xing clip.
Screw point 3
whilst applying downward pressure as
shown to release. View on side of drawer side
Deep
drawer
Front of drawer
Decorative
face
Drawer
base
J
JMetal back
panel
Drawer base
white decorative
face up
Step 3.
Screw back panel in position using
2 x 16mm screws (J) to drawer base in
holes provided.
Step 4.
Frontal Attachment
Secure Drawer Side Fixing Clips using
4 x 21mm screws (Q) and
Gallery Head (Y) using 2 x 21mm screws (L) in
pilot holes provided as shown.
Fixing
clip
Gallery
Head
Repeat step 1 so both drawer
sides are attached to drawer base.
Drawer
frontal
Drawer
frontal
View from
back
Metal
back
panel
J
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 2
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide

REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 3
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
(F) x24
Wooden
Dowel
(L) x24
15mm
Screw
(G) x20
Cam Dowel
(Expanding)
(H) x20
Cam lock
(M) x4
Cover Cap
(K) x16
30mm
Screw
(R) x30
19mm
Screw
(N) x2
Door Buer
(U) x2
Fixing Plate
(Z) x12
Shelf Peg
Plastic
LGE L BRACKET
x2
SML L BRACKET
(FF) x4
HINGE MOUNTING PLATE
x2 Inc Screws
HINGE
x2 (Inc Screws)
Panel B
x2 End Panel
Panel A
x2 Back Panel
Panel E
x2 Rail
Appliance Shelf
x1
Legs
x5
Frontal
x1 (Packed separately)
Panel C
x24 End Panel
600+450 Appliance
Inc 1 Door + 1 Drawer

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd Page 4
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide 2070
Step 1.
Hinge Mounting Plate
Attach hinge plates onto end panels (B) in locations shown using 4x 15mm
screws (L).
Hinge side to be mounted in accordance to customer kitchen plan.
600+450 Appliance
Inc 1 Door + 1 Drawer
N.B. L Bracket
For appliance shelf, secure
to panel (B) using
4 x brackets (FF)
locate according to
customer appliance
requirements.
1826mm
1794mm
1826mm
1794mm
1592mm
1560mm
1592mm
1560mm
Fixed Shelf 1468mm Fixed Shelf 1468mm
Fixed Shelf 282mm Fixed Shelf 282mm
BTM BTM
TOP TOP
74mm 74mm
37mm 37mm
261mm 261mm
from base from base
from front from front
B
LEFT HAND RIGHT HAND
L L
L L
L L
L L
B
Example
Locations
ONLY
Example
Locations
ONLY
FF FFFF FF
J
J
Drawer runner position
J
J

600+450 Appliance
Inc 1 Door + 1 Drawer
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.inddPage 5
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
2250 Tall
Step 2.
Hinge Mounting Plate
Attach hinge plates onto end panels (B) in locations shown using
4x 15mm screws (L).
Hinge side to be mounted in accordance to customer kitchen plan.
N.B. L Bracket
For appliance shelf, secure
to panel (B) using
4 x brackets (FF)
locate according to
customer appliance
requirements.
2006mm
1974mm
2006mm
1974mm
1485mm
1453mm
1485mm
1453mm
Fixed Shelf 1367mm Fixed Shelf 1367mm
Fixed Shelf 282mm Fixed Shelf 282mm
BTM BTM
TOP TOP
74mm 74mm
37mm 37mm
261mm 261mm
from base from base
from front from front
B
LEFT HAND RIGHT HAND
L L
L L
L L
L L
B
Example
Locations
ONLY
Example
Locations
ONLY
FF FFFF FF
J
J
Drawer runner position
J
J
Step 1.
To attach drawer runner screw into end panels (B) using
2 x 16mm screws (J) per drawer rail, into pilot holes provided,3rd hole from
front, as shown.

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 6
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
N.B. L Bracket
For appliance shelf, secure
to panel (B) using
4 x brackets (FF)
locate according to
customer appliance
requirements.
B
B
EE
CC
CC
Step 5.
Carcass Construction
Attach Panels (C) & (E) to panels (B),
using cam dowel (G) & cam lock (H) (in blue),
and also using dowels (F) (in orange)
in positions as shown.
Step 6.
Cam Lock (H)
Join panels (C) & (E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 9.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Seat (G)
cam dowel
into hole
as shown
Step 3.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 4.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
B
B
C
C
View from underside View from underside
H
G
G
H

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 7
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
9mm
9mm
K
A
C
K
Step 7.
Cut back panel (A)
to suit appliance
option, to leaving the
centre appliance aperture open.
B
A A
A
A
C
C
E
E
Step 8.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square with
bottom of end Panels (B).
Step 10.
Ensure carcass is square. Secure back
panel (A) with 12 x 30mm screws (K)
equally spaced at the top & bottom of
back panels (A) into base panels (C),
as shown.
Ensure you screw into the centre of base
panel (C) (9mm from the top or bottom
edge where applicable).
Step 9.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten
the unit together.

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 8
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
9mm
K
B
B
Step 11.
Secure each of the legs into place with 2 x 15mm screws (L) per leg
Step 13.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Step 12.
Lightly hit centre peg of leg base with hammer
until ush with the leg base.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Front
Front
Leg position diagram
C
C
C
B
L
LC
B
B
C
B

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 9
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) to secure each of the L
brackets to the cabinets at either side. Then screw
through into the wall as shown.
Screws for xing to walls are not provided as
these vary depending on your wall material and
construction. Ensure appropriate xings for
wall constructions are used.
Secure tower to the wall using screws through rail panel (E) into the
wall as shown.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.
L
E
E
L
K
Securing to Adjacent Units
Screw into any side units using
the 30mm screws (K) provided to secure to unit.
Screw just to the rear of the Hinge Mounting Plate,
at the top and bottom of both sides of the unit,
place a cover cap on the head to conceal it.

Step 14.
Insert hinge in top & bottom
holes as shown.
Step 15.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 16.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door
clip hinge onto hinge
plate and click to secure.
Hinges
Hinge Cover Caps
Step 18.
Fit cover caps to hinge.
Step 17.
Adjust hinge to suit. As shown below.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- left - right
Point 2- side - side
1
2
FRONTAL HINGE
ADJUSTMENT
Hinge Plates
Hinges
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd
Page 10
TOWER UNIT
600 Double Appliances
Inc Dr+Drw
Assembly Guide
FOR TOWER FRONTALS
SEE CUSTOMER SPECIFIC KITCHEN PLAN