PEERLESS MIS374 Guide

Max Load Capacity: 80 lb (36.3 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED:03-30-07 SHEET#:124-9052-1
Installation and Assembly:
20" Column Tilt Mount for 10" - 24" LCD Flat Panel
Screens Using ST 630
Model: MIS374

2 of 4 ISSUED:03-30-07 SHEET#:124-9052-1
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•phillipsscrewdriver
•drill
•1/4" bit for concrete
•level
• Donot begin toinstall your Peerlessproduct until youhave read andunderstood the instructionsand warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerlesscustomer care at1-800-865-2112.
• Thisproduct should onlybeinstalled by aqualified professional.
• Make sure that the column will safely support the combined load of the equipment and all attached hardware and
components.
• Neverexceed the MaximumLoad Capacity of80lb (36.3 kg).
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, but donotovertighten. Overtightening candamagethe items, greatly reducingtheirholding
power.
WARNING
Forcustomer care call(800)865-2112 or(708)865-8870.
C
B
A
D
EF
MIS374
Description Qty Part #
Acolumn plate 1 201-1291
BAlligator® anchor 2 590-0097
C#14 x 2-1/2" hex head wood screw 2 5S1-015-C03
D1/4-20 x 1/2 phillips screw 2 510-9108
E1/4" flat washer 2 540-9440
F1/4" split washer 2 540-9402
Parts List

3 of 4 ISSUED:03-30-07 SHEET#:124-9052-1
Installation to Solid Concrete Column
1Make sure that column plate (A) is level, use it as a
template to mark four mounting holes. Drill four 1/4"
(6 mm) dia. holes to a minimum depth of 2-1/2"
(64 mm). Insert anchors (B) in holes flush with
columnas shown(right). Place columnplate over
anchors and secure with four #14 x 2-1/2" screws
(C).Level, then tightenall fasteners.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the column will safely support the combined load of the equipment and all attached hardware and
components.
WARNING
CUTAWAY VIEW
INCORRECT
concrete
surface
1
3
2
Drill holes and insert anchors (B).
CORRECT
Place plate (A)over anchors (B) and secure with screws (C).
column
plate
plaster/
drywall
concrete column
plate concrete
plaster/
drywall
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattach concrete expansion anchorstoconcrete
coveredwithplaster,drywall, or other finishingmate-
rial.If mounting toconcretesurfaces covered witha
finishingsurfaceisunavoidable, the finishing surface
must be counterbored asshown below. Be sure
concreteanchors do notpull away fromconcrete
whentightening screws. Ifplaster/drywall is thicker
than 5/8", custom fasteners must be supplied by
installer.
WARNING
A
• Tighten screws so that column plate is firmly attached,
butdonotovertighten. Overtightening can damage
screws,greatlyreducing their holdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING B
C
B
Note: TwoAlligator® anchors andtwo #14 x2-1/2
hexheadwoodscrewsfromST630 fastener pack are
requiredtocompleteassembly.
B
A
Cconcrete
column

4 of 4 ISSUED:03-30-07 SHEET#:124-9052-1
Note: Tilt assembly from ST 630 is required for assembly
Attach tilt assembly to column plate (A) using two 1/4-20 x 1/2 phillips screws (D), two split washers (F) and two flat
washers(E).
2
E
F
D
A
TILT
ASSEMBLY
Refer to Attaching Adapter Plate to Flat Panel Screen section of ST 630 instruction manual to complete assembly.
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Installation of ST 630 Tilt Assembly