Pepperl+Fuchs ICE1-8IOL-S2-G60L-V1D User manual

R
ICE1-8IOL-S2-G60L-V1D
Fieldbus Module with
Multiproto ol Te hnology
and I/O-Link
Manual

With regard to the supply of products, the current issue of the following document is applicable: The
General Terms of Delivery for Products and Services of the Electrical ndustry, published by the Central
Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elektroindustrie (ZVE ) e.V.)
in its most recent version as well as the supplementary clause: "Expanded reservation of proprietor-
ship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [e-mail]
North Ameri an Headquarters
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [e-mail]
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [e-mail]
https://www.pepperl-fuchs.com

3
CE1-8 OL-S2-G60L-V1D
Contents
2020-06
1 Introdu tion................................................................................................................ 5
1.1 Content of this Do ument............................................................................. 5
1.2 Manufa turer .................................................................................................. 5
1.3 Target Group, Personnel ............................................................................... 5
1.4 Symbols Used ................................................................................................ 6
2 Produ t Des ription .................................................................................................. 7
2.1 Use and Appli ation ...................................................................................... 7
2.2 Indi ators and Operating Elements............................................................. 9
2.3 Interfa es and Conne tions ....................................................................... 11
2.4 Dimensions................................................................................................... 15
3 Installation................................................................................................................ 16
3.1 General Information..................................................................................... 16
4 Commissioning, Proto ol Setting.......................................................................... 17
4.1 Proto ol Setting ........................................................................................... 17
5 Commissioning for PROFINET............................................................................... 19
5.1 Preparation ................................................................................................... 19
5.2 Configuration Example ............................................................................... 19
5.2.1 ntegration of PROF NET O Modules in the T A Portal .................... 20
5.2.2 Assigning a Unique Device Name in the Control System ................. 22
5.2.3 Assigning the Device Name to a PROF NET O Module.................. 23
5.2.4 Configuring the O-Link Channels.................................................... 26
5.2.5 Parameterization of the O-Link Channels........................................ 29
5.2.5.1 Fail-Safe Configuration (Outputs Only) .................................................................................. 29
5.2.5.2 Port Parameters in O-Link Mode ........................................................................................... 30
5.2.6 Parameterization of the Status/Control Module................................ 33
5.2.6.1 General Device Settings ........................................................................................................ 34
5.2.6.2 General Diagnostic Settings .................................................................................................. 36
5.2.6.3 Fail-Safe Configuration .......................................................................................................... 37
5.2.6.4 Surveillance Timeout Configuration ....................................................................................... 37
5.2.6.5 Digital nput Logic .................................................................................................................. 38
5.2.6.6 Digital- O-mode for Ch. B/Pin 2 .............................................................................................. 38
5.2.7 Siemens O-Link Library .................................................................. 39
5.2.8 Replacing Devices Without a Removable Medium/Programming Unit....40
5.2.9 dentification and Maintenance Functions ( &M) .............................. 42
5.2.10 Prioritized Start-Up/Fast Start-Up (FSU) .......................................... 46
5.2.11 Resetting Modules to their Factory Settings..................................... 46
5.3 Bit Assignment............................................................................................. 48

CE1-8 OL-S2-G60L-V1D
Contents
4
2020-06
6 The Integrated Web Server .....................................................................................52
7 Troubleshooting.......................................................................................................57
7.1 Diagnosti s Indi ator in the Integrated Web Server ................................57
7.2 Alarm Signals and Error Messages from Modules via PROFINET..........57
7.3 Alarm Signals and Error Messages via Ethernet IP .................................59

CE1-8 OL-S2-G60L-V1D
ntroduction
2020-06
5
1 Introdu tion
1.1 Content of this Do ument
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
n addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•nstruction manual
•Other documents
1.2 Manufa turer
1.3 Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product. The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the nternet at
www.pepperl-fuchs.com.
Pepperl+Fuchs Group
Lilienthalstraße 200, 68307 Mannheim, Germany
nternet: www.pepperl-fuchs.com

2020-06
6
CE1-8 OL-S2-G60L-V1D
ntroduction
1.4 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Warning Messages
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
Informative Symbols
A tion
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

CE1-8 OL-S2-G60L-V1D
Product Description
2020-06
7
2 Produ t Des ription
2.1 Use and Appli ation
The CE1-8 OL-* modules function as an interface in an industrial fieldbus system. They enable
communication between a central controller at the control level and the decentralized sensors
and actuators at the field level. The resulting potential line or ring topologies that can be
achieved enable reliable data communication and a significant reduction in the amount of wir-
ing required, and therefore in the costs for installation and maintenance. Simple and quick
extension is also possible.
The CE1-8 OL-* series modules have a rugged metal housing made of die-cast zinc. Due to
the fully encapsulated device housing, the module electronics are protected against environ-
mental influences and can be used in a wide range of temperatures. Despite the rugged
design, the modules have compact dimensions and a low weight. They are especially suitable
for use in machines and plants with a moderate /O concentration on distributed assemblies.
Multiproto ol (EtherNet/IP, PROFINET)
The multiprotocol modules allow you to select different protocols for communication within a
fieldbus system. As a result, multiprotocol modules can be integrated into different networks
without the need to obtain specific modules for each protocol. Thanks to this technology, you
can also use one module in different environments.
Using rotary coding switches in the lower area of the modules, you can conveniently and easily
set both the protocol and the address of the module, provided that the protocol to be used sup-
ports this. f you have chosen a protocol and started the cyclic communication once, the mod-
ule remembers this setting and uses the selected protocol from this point on. To use another
supported protocol with this module, perform a factory reset.
Input/Output Channels for the Field Level
For the field level, the modules have the following input/output channels
•8 O-Link master ports
•4 O-Link master ports, class A
•4 O-Link master ports, class B
f one or more of the O-Link ports are not required, these can also be freely configured as digi-
tal inputs or outputs (S O mode).
•4 hardwired digital inputs
•4 configurable digital outputs (instead of the voltage outputs of class B master ports on pin
2)
IO-Link Chara teristi s of the Modules
The modules support O-Link Standard V1.1.
•Parametrization of O-Link devices in PROF NET using Siemens O_L NK_DEV CE func-
tion blocks for Step 7 and the T A Portal
8 x O-Link master ports
• 4 class A connections with an additional hardwired digital input at pin 2 of the /O port.
•4 class B connections with a galvanically isolated auxiliary power supply for up to 2 A per
port at pins 2 and 5 with a total current of 8 A.
•The auxiliary power supply can be configured as a digital output.
O-Link connections
•5-pin M12 connector

2020-06
8
CE1-8 OL-S2-G60L-V1D
Product Description
Parameter storage
•The Parameter Storage function stores and monitors the parameters of the O-Link device
and the O-Link master.
•This function makes it possible for you to easily replace the O-Link device or the O-Link
master.
This is possible from O-Link specification V1.1 onward and only if the O-Link device and
the O-Link master support the function.
O-Link device parameterization
•The O-Link devices can be parameterized in the PROF NET protocol using the Siemens
O_L NK_DEV CE function block for STEP 7 and the T A Portal.
Spe ial Produ t Features
•Rugged design:
Connectivity options for the module series include the widespread M12 connector with A
coding for /O signals and D coding for the network. n addition, the connectors are color-
coded to prevent users from using the wrong ports. The output circuits are galvanically
isolated from the rest of the network and the sensor electronics. Controllers are therefore
reliably protected against noise.
•Integrated web server:
Network parameters such as P address, subnet mask, and gateway can be adjusted via
the integrated web server. The modules support the communication protocols BOOTP
and DHCP for automated assignment of network parameters via the corresponding serv-
ers.
You can read the parameters of the O-Link device via the integrated web server and write
new parameters to the modules in single-write mode. Single-write mode does not activate
the automatic parameter storage mechanism.
•For e Mode
n Force Mode, the module ports can be temporarily configured as digital inputs/outputs or
O-Link ports. The configuration applies until the module is next switched off.
"Force Mode" allows the simulation of process data at the digital inputs/outputs without
the need to connect sensors and actuators. This means that you can test an application in
advance without a full physical application. t is possible to simulate input switching states
or to switch outputs even without a controller. This feature makes machine commissioning
simpler and quicker and can be used to test new production plants.
•Integrated network swit h:
The integrated two-port Ethernet switch of the modules allows you to set up a line topol-
ogy or a ring topology for the EtherNet/ P network or PROF NET network. The additional
DLR or MRP protocol allows you to design a highly available network infrastructure.
•Redundan y fun tion:
The module firmware supports the redundancy function DLR (Device Level Ring) or MRP
(Media Redundancy Protocol) for ring topologies. This means that if the connection is
interrupted, the modules switch immediately to an alternative ring segment and thus
ensure interruption-free operation. The supported DLR class is "beacon-based" in accor-
dance with the EtherNet/ P specification.
•Fail-safe fun tion:
The modules provide a fail-safe function. You can therefore choose the behavior of each
individual output channel in the event of an interruption or a loss of communication.

CE1-8 OL-S2-G60L-V1D
Product Description
2020-06
9
•Qui kConne t:
QuickConnect allows the modules to record the communication in an EtherNet/ P network
especially quickly through an accelerated boot-up process. This allows you to switch tools
faster, for example.
•S2 system redundan y:
S = single network access point
2 = switching between two application relationships is possible
The S2 system redundancy uses a system from a PROF NET device that is connected to
two redundant PROF NET controllers. This arrangement allows the additional controller
to take over the O data exchange connection if the connection to the primary controller
fails.
Normally, a connection failure to the main controller triggers the switch to an additional
controller. A manual switch can be forced via the additional controller.
2.2 Indi ators and Operating Elements
ICE1-8IOL-S2-G60L-V1D
Channel indicator LED
Status indicator LED
Rotary switch
20X10X
X03
X4 X8
7X
3
X
X6
5X1X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
X02
X01
US
UAux
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
PN
00
1
2
3
1
2
3

2020-06
10
CE1-8 OL-S2-G60L-V1D
Product Description
Indi ators—General Part
Description for LED A, B, D A, U
S
, U
Aux
Note
The LEDs in the lower area of the Ethernet O module have different names and functions
depending on the selected protocol. The following LED descriptions are therefore divided into
a general part (1), which is valid for all protocol settings, and LED descriptions for a specific
protocol setting (2).
Figure 2.1
X4 X8
BF DIA
Lnk/Act
X02
X01
US UAux
A
DIA
B
x100 x10 x1
MS NS
0E/IP
PN
00
1
2
G60L
LED Fun tion
D A
LED A (for each of X1 -
X8 A)
Red: peripheral error (sensor/actuator overload or short circuit)
SIO mode
Yellow: channel A status (pin 4) is "on"
Off: no error, not connected
IO-Link mode
Green: O-Link communication present
Flashing green: no O-Link device connected
Off: not configured for O-Link
D A
LED B (for each of X1 –
X8 B)
Red: peripheral fault (sensor and actuator overload or short circuit at
line L+ (pin 1))
SIO mode
White: channel B status (pin 2) is "on"
Red: overload or short circuit at C/Q (pin 4) line
Off: no error, not connected
IO-Link mode
Red: O-Link COM mode: O-Link communication error or overload
or short circuit at C/Q (pin 4) line
Flashing green: no O-Link device connected
Off: not configured for O-Link
LED U
S
Green: voltage 19 V  U
S
 30 V
Red: voltage U
S
< 19 V or U
S
> 30 V
LED U
Aux
Green: voltage 19 V  U
Aux
 30 V
Red: voltage U
Aux
< 19 V or U
L
> 30 V
Red alert is only possible if, for EtherNet/ P, the option "Report U
Aux
supply voltage fault" is enabled in "General Diagnostic Settings" or,
for PROF NET, the option "U
Aux
supply diagnosis" is enabled in
"Global Diagnostic Parameters."
Table 2.1

CE1-8 OL-S2-G60L-V1D
Product Description
2020-06
11
EtherNet/IP indi ators
E/ P areas: relevant LEDs Lnk/Act X01, Lnk/Act X02, MS, NS
PROFINET Indi ators
P area: relevant LEDs Lnk/Act X01, Lnk/Act X02, BF, D A
Operating Elements
LED Fun tion
LED Lnk/Act X01
LED Lnk/Act X02
Green: connected to an Ethernet node
Flashing yellow: data exchange with an O device
Off: no connection
LED MS Green: module ready for operation
Flashing green: missing configuration
Flashing red/green: self-test
Red: non-recoverable, serious error
Flashing red: minor recoverable error (e.g., incorrect configuration)
Off: module switched off
LED NS Green: module has at least one connection
Flashing green: module has no connections. P address is available
Red/green: module is performing a self-test
Red: module has determined that the assigned P address already
exists
Flashing red: the connection has timed out or been interrupted
Off: module is turned off or does not have an P address
Table 2.2
LED Fun tion
LED Lnk/Act X01
LED Lnk/Act X02
Green: connected to an Ethernet node
Flashing yellow: data exchange with an O device
Off: no connection
LED BF Red: no configuration, slow or no physical connection
Flashing red: link exists but no communication link to the PROF NET
controller is available
Off: no error
LED D A Red: PROF NET diagnostic alarm active
Flashing red (1 Hz): time-out or fail-safe mode is active
Flashing red (2 Hz) for 3 sec: DCP signal service triggered via the bus
Red double flashing: firmware update
Off: no error
Table 2.3
Swit h Fun tion
Rotary switch X100 Setting the fieldbus protocol
Setting the P address
1
1. Only EtherNET/ P
Rotary switch X10 Setting the P address
2
2. Only EtherNET/ P
Rotary switch X1 Setting the P address
3
3. Only EtherNET/ P

2020-06
12
CE1-8 OL-S2-G60L-V1D
Product Description
2.3 Interfa es and Conne tions
The contact arrangements below show the front view of the plug-in area of the connectors.
Fieldbus Conne tion X01, X02
•Connection: M12 socket, 4 pin, D-coded
•Color coding: green
Figure 2.2 Schematic drawing of port X01, X02
Conne tion for IO-Link, digital inputs/outputs X1 - X8
•Connection: M12 socket, 5 pin, A-coded
•Color coding: black
Caution!
Risk of destruction!
Never route the power supply to the data cable.
Port Pin Signal Fun tion
Ports X01, X02 1 TD+ Transmit data +
2 RD+ Receive data +
3 TD- Transmit data -
4 RD- Receive Data -
Table 2.4 Assignment of port X01, X02
1
3
2
4
Caution!
Risk of destruction with external sensor supply!
The module infeed for the sensor supply U
S
may only be provided over the specified power
connection (Power X03/X04 >> U
S
+24 V/GND_U
S
) for the module. t is not permitted to supply
external power via the O-Port (port X1 - X8 >> pin 1/pin 3) and this may destroy the module
electronics through power feedback.
Caution!
Do not compromise galvanic isolation through incorrect cabling!
The sensor supply (port X5 - X8 >> pin 1/pin 3) and extended sensor supply (port X5 - X8 >>
pin 2/pin 5) are galvanically isolated from each other. f the reference potentials (GND_
US
– pin
3) and (GND_U
Aux
– pin 5) are connected, excessive equalization currents may flow. n this
case, it is not permitted for a sensor to be connected to (port X5 - X8 >> pin 2)!
Eliminating the galvanic isolation is not recommended.

CE1-8 OL-S2-G60L-V1D
Product Description
2020-06
13
Figure 2.3 Schematic drawing of inputs/outputs 1 - 8
Conne tion for Power Supply X03, X04
•Power supply with M12 power L-coded
•Color coding: gray
Caution!
Risk of destruction!
Never route the power supply to the data cable.
Port Pin Signal Fun tion
O-Link Class A, inputs/out-
puts
X1 ... X4
1 L+ O-Link sensor power supply
+24 V
2 N-x Channel B: digital input (type
1)
3 L- O-Link sensor power supply
GND_U
S
4 C/Q Channel A: O-Link data
exchange
5 n.c. Not used
Port Pin Signal Fun tion
O-Link Class B, inputs/out-
puts
X5 ... X8
1 L+ O-Link sensor power supply
+24 V
2 U
AUX
(+24 V) Channel B: auxiliary voltage,
galvanically isolated from the
O-Link/module power supply
3 L- O-Link sensor power supply
GND_U
S
4 C/Q Channel A: O-Link data
exchange
5 GND_U
AUX
Protective earth, reference
potential U
AUX
1
5
3
2
4
Note
For the system/sensor and actuator supply, use only power supplies that comply with PELV
(protective extra-low voltage) or SELV (safety extra-low voltage). Power supplies according to
EN 61558-2-6 (transformer) or EN 60950-1 (switching power supplies) fulfill these
requirements.

2020-06
14
CE1-8 OL-S2-G60L-V1D
Product Description
Figure 2.4 Schematic drawing of M12 L-encoding (plug); port X03 ( N)
Figure 2.5 Schematic drawing of M12 L-encoding (socket); port X04 (OUT)
Caution!
Loss of function when the system supply voltage is too low.
Ensure in all cases that the supply voltage measured at the most remote participants (sen-
sor/actuator) does not drop below 18 V DC in terms of system supply voltage.
Note
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary voltage via U
Aux
for e.g., actuators. Where the plant has a separate power
supply concept for system current and load current, this means the sensor and system area of
the Ethernet O module can continue working even if there is a failure of the load power supply.
Where several Ethernet O modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
Aux
.
Port Pin Signal Fun tion
Power supply
X03, X04
1 U
S
(+24 V) Sensor/system supply
2 GND U
Aux
Ground/reference potential U
Aux
3 GND U
S
Ground/reference potential U
s
4 U
Aux
(+24 V) Auxiliary voltage (galv. insulated)
FE (5) FE (FE) Functional ground
4
1
3
2
FE
4
1
3
2
FE

CE1-8 OL-S2-G60L-V1D
Product Description
2020-06
15
2.4 Dimensions
Figure 2.6
ICE1-8IOL-S2-G60L-V1D
17.6
30.7
214.5
20
30
59.6
27 27 27 M12 x1 (10x) 27 11.5
16.5
190.3
191.8
200
M4

2020-06
16
CE1-8 OL-S2-G60L-V1D
nstallation
3 Installation
3.1 General Information
nstall the module with two M6x25/30 size screws on a level surface. The required torque is
1 Nm. Use washers according to D N 125. For the installation holes, use a spacing of
237.3 mm to 239.7 mm.
Note
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary supply via U
Aux
for e.g., actuators. Where the plant has a separate power
supply concept for system current and load current, this means the sensor and system area of
the Ethernet O module can continue working even if there is a failure of the load power supply.
Where several Ethernet O modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
Aux
.
Note
To dissipate interference currents and the EMC resistance, the modules use a short circuit to
ground with an M4 thread. This is marked with the symbol for grounding and the label "XE."
Note
Connect the module using a low-impedance connection with the reference ground. n the case
of a grounded mounting surface, you can connect the module directly via the fixing screws.
Note
For non-grounded mounting surfaces, use a ground strap or a suitable FE conductor. Connect
the ground strap or FE conductor to the grounding point using an M4 screw and place a washer
and a serrated washer under the fixing screw if possible.
Note
Use a suitable UL-certified cable (CYJV or PVVA). To program the controller, please consult the
manufacturer information and use only the appropriate accessories.
Note
For UL application:
Approved only for indoor use. Please observe the maximum altitude of 2000 meters. Approved
up to a maximum of pollution degree 2.
Warning!
Terminals, the housing of field-wired terminal boxes or components may exceed a temperature
of 60 °C.
Warning!
Use temperature-resistant cables with the following properties:
Heat resistant up to at least 96 °C.

CE1-8 OL-S2-G60L-V1D
Commissioning, Protocol Setting
2020-06
17
4 Commissioning, Proto ol Setting
4.1 Proto ol Setting
Multiproto ol
You can use the multiprotocol modules to select various protocols for communication within a
fieldbus system. This allows you to integrate the multiprotocol modules into different networks
without having to obtain a specific module for each protocol. This technology also allows you to
use the same module in different environments. Using the rotary switches on the front of the
modules, you can easily and conveniently set the protocol and address of the module, provided
that the protocol to be used supports this. Once you have selected a protocol and started the
cyclical communication, the module recognizes these settings and uses the selected protocol
from this point on. To use another supported protocol with this module, perform a factory reset.
Setting a Proto ol
Multiprotocol modules have a total of three rotary switches. Move the first rotary switch X100 to
the relevant switch position to set the protocol. f you use EtherNet/ P, set the last octet of the P
address using the rotary switches (X100, X10, X1).
Figure 4.1 Rotary switch X100
Assigning the Proto ol Using the Rotary Swit hes
n its delivered state, the module does not contain any protocol settings. n this case, simply
select the desired protocol. To use a modified rotary switch setting (protocol setting), you must
perform a power cycle or a "Reset" via the web interface. Once you have set the protocol using
the rotary switches, the module saves these settings as soon as it starts a cyclical communica-
tion. You can no longer change the protocol using the rotary switch from this point on. To
change the protocol, perform a factory reset first.
f you set the rotary coding switch to an invalid position, the device signals this with a flash
code: the BF/MS/ERR LED flashes red three times.
The P address can be changed depending on the selected protocol.
Proto ol X100 X10 X1
EtherNet/ P 0 – 2 0 – 9 0 – 9
PROF NET P - -
20X10X
X03
X4 X8
7X3X
X6
5X1X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
P2
P1
US
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
PN
00
R
0E/IP
PN
X100
1
2
9

2020-06
18
CE1-8 OL-S2-G60L-V1D
Commissioning, Protocol Setting
EtherNet/IP
f you use EtherNet/ P as the protocol, use rotary switch X100 to set the value 100 as the last
octet of the P address for the module. You can use rotary switch X100 to set a value of 0 to 2
for the P address. You can use rotary switches X10 and X1 to select values between 0 and 9.
You can use rotary switch X10 to configure position 10 of the last octet of the P address. You
can use rotary switch X1 to configure position 1 of the last octet of the P address.
The default setting for the first three octets of the P address is 192.168.1.
Example: Rotary switch settings 2 (X100), 1 (X10), and 0 (X1) result in an P address of
192.168.1.210 for EtherNet/ P.
PROFINET
f you use PROF NET as the protocol, only set rotary switch X100 to the value "P."
Fa tory Settings
A factory reset erases any changes you have made to settings, etc. and restores the factory
settings. The saved protocol selection is also reset.
To perform a factory reset, set rotary switch X100 to 9, rotary switch X10 to 7, and rotary switch
X1 to 9. Then switch the module off and on again. The factory settings are restored after 10
seconds.
To select a new protocol, follow the instructions in this chapter.
Figure 4.2 Restoring factory settings: X100 = 9, X10 = 7, X1 = 9
20X10X
X03
X4 X8
7X3X
X6
5
X1
X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
P2
P1
US
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
P
00
X100
0
E/IP
P
X10 X1
9 1
2
01
2
3
4
5
6
7
8
901
2
3
4
5
6
7
8
9
Caution!
Destruction of the Operating System
When restoring the factory settings, ensure that the module is connected to the voltage supply
and switched on for at least 10 seconds. f it has been on for less than 10 seconds, the operat-
ing system may be destroyed. The module would then need to be sent to Pepperl+Fuchs for
repair.

CE1-8 OL-S2-G60L-V1D
Commissioning for PROF NET
2020-06
19
5 Commissioning for PROFINET
5.1 Preparation
The configuration and commissioning process for the modules described over the following
pages was performed using T A Portal V15 project planning software from S EMENS. When
using a control system from a different controller provider, please refer to the corresponding
documentation.
GSDML File
To configure the modules in the control system, you need a GSD file in XML format. You can
download this file from our website at https://www.pepperl-fuchs.com.
The file for the PROF NET modules is named GSDML-V2.3*-Pepperl-Fuchs- CE1-S2-yyyym-
mdd.xml. n this case, yyyymmdd is the issue date of the file.
ntegrate the GSDML file into the T A Portal using the GSD manager via the main menu
"Options > Manage general station description files (GSD)." The modules with a PROF NET
interface are then available in the hardware catalog.
Figure 5.1
MAC IDs
The modules have three assigned MAC Ds when they are delivered. These are unique and
cannot be changed by the user.
The first assigned MAC D is printed on the module.
SNMP
The modules support the SNMP Ethernet network protocol (Simple Network Management Pro-
tocol). The information from the network management system is displayed in accordance with
M B- (Management nformation Base), which is defined in RFC 1213.
Passwords:
Read community: public
Write community: private
5.2 Configuration Example
The configuration and commissioning process for the modules described over the following
pages was performed using T A Portal V15 project planning software from S EMENS. The con-
figuration is based on the example of an CE1-8 OL-S2-G60L-V1D module. For other module
versions, configuration is carried out with a few minor changes.

2020-06
20
CE1-8 OL-S2-G60L-V1D
Commissioning for PROF NET
5.2.1 Integration of PROFINET IO Modules in the TIA Portal
As an example, the following is an explanation of how to configure an Ethernet O module as a
PROF NET type in the T A portal, based on the CE1-8 OL-S2-G60L-V1D module.
1. nstall the GSDML file for the desired module in the T A Portal.
Once the GSDML file for the PROF NET modules has been installed, the modules are avail-
able in the T A portal hardware catalog.
Figure 5.2
2. Double-click on the desired module and select the corresponding PROF NET interface.
Note
To configure a module in the control system, you need a GSDML file.