Pepperl+Fuchs ICE1-8IOL-G60L-V1D User manual

R
ICE1-8IOL-G60L-V1D,
ICE1-8IOL-G30L-V1D
Fieldbus Module with
Multiproto ol Te hnology
and I/O-Link
FACTORY AUTOMATION
MANUAL

With regard to the supply of products, the current issue of the following document is ap-
plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-
try, published by the Central Association of the lectrical Industry (Zentralverband
lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the
supplementary clause: " xpanded reservation of proprietorship"
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
3
1 Introdu tion................................................................................. 5
1.1 Content of this Do ument ................................................................... 5
1.2 Manufa turer ........................................................................................ 5
1.3 Target Group, Personnel...................................................................... 5
1.4 Symbols Used ...................................................................................... 5
2 Produ t Des ription ................................................................... 7
2.1 Use and Appli ation ............................................................................ 7
2.2 Displays and Operating Elements...................................................... 9
2.3 Interfa es and Conne tions.............................................................. 11
2.4 Dimensions......................................................................................... 15
3 Installation................................................................................. 16
3.1 General Information........................................................................... 16
4 Commissioning, Proto ol Setting ........................................... 17
4.1 Setting Proto ols ............................................................................... 17
5 Commissioning for EtherNet/IP .............................................. 19
5.1 Preparation ......................................................................................... 19
5.2 Configuration Example...................................................................... 20
5.3 IO-Link Master Parameters ............................................................... 23
5.4 Conne tions and Assembly Obje t.................................................. 33
5.5 Bit Assignment................................................................................... 36
5.5.1 Status Data of the IO-Link Master (Inputs) ....................................... 36
5.5.2 IO-Link Device Input Data ................................................................ 39
5.5.3 IO-Link Input & xtended IO-Link Status Data ................................. 41
5.5.4 IO-Link Input Data & xtended IO-Link Status Data
& IO-Link vent Data........................................................................ 44
5.5.5 Control Data of the IO-Link Master (Outputs)................................... 49
5.5.6 Control Data of the IO-Link Device (Outputs)................................... 50
5.6 EtherNet/IP Obje ts ........................................................................... 51

4
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
6 Commissioning for PROFINET................................................ 55
6.1 Preparation..........................................................................................55
6.2 Configuration Example ......................................................................55
6.2.1 Integration of PROFIN T IO Modules in the TIA Portal..................... 56
6.2.2 Assigning a Unique Device Name in the Control System ................. 58
6.2.3 Assigning the Device Name to a PROFIN T IO Module .................. 59
6.2.4 Configuring the IO-Link Channels ....................................................62
6.2.5 Parameterization of the IO-Link Channels ........................................ 66
6.2.6 Parameterization of the Status/Control Module ................................ 70
6.2.7 Siemens IO-Link Library................................................................... 74
6.2.8 Replacing Devices Without a Removable Medium/
Programming Unit ............................................................................75
6.2.9 Identification and Maintenance Functions (I&M)............................... 78
6.2.10 Prioritized Start-Up/Fast Start-Up (FSU)........................................... 81
6.2.11 Resetting Modules to their Factory Settings .....................................82
6.3 Bit Assignment ...................................................................................84
7 The Integrated Web Server...................................................... 89
8 Troubleshooting........................................................................ 95
8.1 Diagnosti s Indi ator in the Integrated Web Server.......................95
8.2 Alarm Signals and Error Messages from Modules via PROFINET 95
8.3 Alarm Signals and Error Messages via Ethernet IP........................97

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Introduction
2019-02
1
1 Introduction
1.1 Content of this Document
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
■ Product identification
■ Delivery, transport, and storage
■ Mounting and installation
■ Commissioning and operation
■ Maintenance and repair
■ Troubleshooting
■ Dismounting
■ Disposal
The documentation comprises the following parts:
■ This document
■ Datasheet
In addition, the documentation may comprise the following parts, if applicable:
■ U-type examination certificate
■ U declaration of conformity
■ Attestation of conformity
■ Certificates
■ Control drawings
■ Instruction manual
■ Other documents
1.2 Manufacturer
1.3 Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and
dismounting lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation,
commissioning, operation, maintenance, and dismounting of the product. The personnel must
have read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
1.4 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Note!
For full information on the product, refer to the further documentation on the Internet at
www.pepperl-fuchs.com.
Pepperl+Fuchs GmbH
Lilienthalstraße 200, 68307 Mannheim, Germany
Internet: www.pepperl-fuchs.com

2019-02
2
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Introduction
Warning Messages
You will find warning messages, whenever dangers may arise from your actions. It is mandatory
that you observe these warning messages for your personal safety and in order to avoid
property damage.
Depending on the risk level, the warning messages are displayed in descending order as
follows:
Informative Symbols
Action
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note!
This symbol brings important information to your attention.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
2019-02
7
2 Product Description
2.1 Use and Application
The IC 1-8IOL-* modules function as an interface in an industrial fieldbus system. They enable
communication between a central controller at the control level and the decentralized sensors
and actuators at the field level. The resulting potential line or ring topologies that can be
achieved enable reliable data communication and a significant reduction in the amount of
wiring required, which therefore makes the costs for installation and maintenance reasonable.
Simple and quick extension is also possible.
The IC 1-8IOL-* series modules have a robust metal housing made of die-cast zinc. Due to the
fully encapsulated device housing, the module electronics are protected against environmental
influences and can be used in a wide range of temperatures. Despite the robust design, the
modules have compact dimensions and a low weight. They are especially suitable for use in
machines and plants with a moderate I/O concentration on distributed assemblies.
Multiproto ol (EtherNet/IP, PROFINET)
The multiprotocol modules allow you to select different protocols for communication within a
fieldbus system. As a result, multiprotocol modules can be integrated into different networks
without the need to purchase protocol-specific modules. Thanks to this technology, you can
also use one and the same module in different environments.
Using rotary coding switches in the lower area of the modules, you can comfortably and easily
set both the protocol and the address of the module, provided the protocol to be used supports
this. If you have chosen a protocol and started the cyclic communication once, the module
remembers this setting and uses the selected protocol from this point on. To use another
supported protocol with this module, perform a factory reset.
Input/Output Channels for the Field Level
For the field level, the modules have the following input/output channels
■ 8 IO-Link master ports
• 4 IO-Link master ports Class A
• 4 IO-Link master ports Class B
If one or more of the IO-Link ports are not required, these can also be freely configured as
digital inputs or outputs (SIO mode).
■ 4 hardwired digital inputs
■ 4 configurable digital outputs (instead of the voltage outputs of Class B master ports on
pin 2)
IO-Link Chara teristi s of the Modules
The modules support IO-Link Standard V1.1.
■ Parametrization of IO-Link devices in PROFIN T using Siemens IO_LINK_D VIC
functional modules for Step 7 and the TIA Portal
8 x IO-Link master ports
■ 4 Class A connections with an additional hard-wired digital input at pin 2 of the I/O port.
■ 4 Class B connections with a galvanically isolated auxiliary power supply for up to 2 A per
port at pins 2 and 5 with a total current of 8 A.
■ The auxiliary power supply can optionally be configured as a digital output.

2019-02
8
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
IO-Link connections
■ 5-pin M12 connector
Parameter memory
■ The parameter storage function stores and monitors the parameters of the IO-Link device
and the IO-Link master.
■ The function makes it possible for you to easily replace the IO-Link device or the IO-Link
master.
This is possible from the IO-Link specification V1.1 and only if the IO-Link device and the
IO-Link master support the function.
IO-Link device parameterization
■ The IO-Link devices can be parameterized in the PROFIN T protocol using the Siemens
IO_LINK_D VIC functional module for ST P 7 and the TIA Portal.
Spe ial Produ t Features
■ Robust design:
Connectivity options for the module series include the widespread M12 connector with A
encoding for I/O signals and D coding for the network. In addition, the connectors are
color-coded to prevent confusion of the ports. The output circuits are galvanically isolated
from the rest of the network and the sensor electronics. Controllers are therefore reliably
protected against noise.
■ Integrated web server:
Network parameters such as IP address, subnet mask, and gateway can be adjusted via
the integrated web server. The modules support the communication protocols BOOTP
and DHCP for automated assignment of network parameters via the corresponding
servers.
You can read the parameters of the IO-Link device via the integrated web server and write
new parameters to the modules in single-write mode. Single-write mode does not activate
the automatic parameter storage mechanism.
■ For e Mode
In Force Mode, the module ports can be temporarily configured as digital inputs/outputs or
IO-Link ports. The configuration applies until the module is next switched off.
"Force Mode" allows the simulation of process data at the digital inputs/outputs without
the need to connect sensors and actuators. This means you can test an application in
advance without a full physical application. It is possible to simulate input switching states
or to switch outputs even without a controller. This feature eases and accelerates machine
commissioning and can be used to test new production plants.
■ Integrated network swit h:
The integrated two-port thernet switch of the modules allows you to set up a line
topology or a ring topology for the therNet/IP network or PROFIN T network. The
additionally implemented DLR or MRP protocol allows you to design a highly available
network infrastructure.
■ Redundan y fun tion:
The module firmware supports the redundancy function DLR (Device Level Ring) or MRP
(Media Redundancy Protocol) for ring topologies. This means that if the connection is
interrupted, the modules switch immediately to an alternative ring segment and thus
ensure interruption-free operation. The DLR class supported is "beacon-based" in
accordance with the therNet/IP specification.
■ Fail-safe fun tion:
The modules provide a fail-safe function. You can therefore choose the behavior of each
individual output channel in the event of an interruption or a loss of communication.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
2019-02
9
■ Qui kConne t:
QuickConnect allows the modules to record the communication in an therNet/IP network
particularly quickly through an accelerated boot-up process. This allows you to switch
tools faster, for example.
2.2 Displays and Operating lements
ICE1-8IOL-G30L-V1D
L D channel indicator
L D status indicator
Rotary switch
ICE1-8IOL-G30L-V1D
L D channel indicator
L D status indicator
Rotary switch
20X10X
X03
X4 X8
7X
3
X
X6
5
X1
X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
X02
X01
US UAux
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
PN
00
1
2
3
1
2
3
X01
X4
X8
X3
X7
X6
X1
X5
X2
A B
XE
Power
IO-Link
BF DIA
X02
X01 USUAux
X03
X02
X04
A B
A B
A B
A B
A B
A B
A B
Link/Act
P
E/IP
x100
x10
x1
MS NS
1
2
3
1
2
3

2019-02
10
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
Displays—General Part
Description for L D A, B, DIA, U
S
, U
Aux
Note!
The L Ds in the lower area of the thernet IO module have different names and functions
depending on the selected protocol. The following L D descriptions are therefore divided into
a general part (1), which is valid for all protocol settings, and L D descriptions for a specific
protocol setting (2).
Figure 2.1
X4 X8
BF DIA
Lnk/Act
X02
X01
US
UAux
A
DIA
B
x100 x10 x1
MS NS
0E/IP
PN
00
1
2
X8
BF DIA
X02
X01 USUAux
A B
Link/Act
P
E/IP
x100
x10
x1
MS NS
G60L G30L
1
2
L D Function
DIA
L D A (for each of X1
- X8 A)
Red: peripheral error (sensor/actuator overload or short circuit)
SIO mode
Yellow: channel A status (pin 4) is "on"
Off: no error, not connected
IO-Link mode
Green: IO-Link communication present
Flashing green: no IO-Link device connected
Off: not configured for IO-Link
DIA
L D B (for each of X1
- X8 B)
Red: peripheral fault (sensor and actuator overload or short circuit at
line L+ (pin 1))
SIO mode
White: Channel B status (pin 2) is "on"
Red: Overload or short circuit at C/Q (pin 4) line
Off: no error, not connected
IO-Link mode
Red: IO-Link COM mode: IO-Link communication error or overload or
short circuit at C/Q (pin 4) line
Flashing green: no IO-Link device connected
Off: not configured for IO-Link
L D U
S
Green: voltage 19 V  U
S
 30 V
Red: voltage U
S
< 19 V or U
S
> 30 V
L D U
Aux
Green: voltage 19 V  U
Aux
 30 V
Red: voltage U
Aux
< 19 V or U
L
> 30 V
Red alert is only possible if, for therNet/IP, the option "Report U
Aux
supply voltage fault" is enabled in "General Diagnosis Settings" or, for
PROFIN T, the option "U
Aux
supply diagnosis" is enabled in "Global
Diagnostic Parameters."
Table 2.1

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
2019-02
11
EtherNet/IP Displays
/IP areas: relevant L Ds Lnk/Act X01, Lnk/Act X02, MS, NS
PROFINET Displays
P area: relevant L Ds Lnk/Act X01, Lnk/Act X02, BF, DIA
Operating Elements
L D Function
L D Lnk/Act X01
L D Lnk/Act X02
Green: connection to an thernet node
Flashing yellow: data exchange with an IO device
Off: no connection
L D MS Green: module ready for operation
Flashing green: missing configuration
Flashing red/green: self-test
Red: non-recoverable, serious error
Flashing red: minor recoverable error (e.g., incorrect configuration)
Off: module switched off
L D NS Green: module has at least one connection
Flashing green: module has no connections. IP address is available
Red/green: module is performing a self-test
Red: module has determined that the assigned IP address already
exists
Flashing red: the connection has timed out or been interrupted
Off: module is turned off or does not have an IP address
Table 2.2
L D Function
L D Lnk/Act X01
L D Lnk/Act X02
Green: connection to an thernet node
Flashing yellow: data exchange with an IO device
Off: no connection
L D BF Red: no configuration, slow or no physical connection
Flashing red: link exists but no communication link to the PROFIN T
controller
Off: no error
L D DIA Red: PROFIN T diagnostic alarm active
Flashing red (1 Hz): time-out or fail-safe mode is active
Flashing red (2 Hz) for 3 sec: DCP signal service triggered via the bus
Red double flashing: firmware update
Off: no error
Table 2.3
Switch Function
Rotary switch X100 Setting the fieldbus protocol
Setting the IP address
1
1.Only therN T/IP
Rotary switch X10 Setting the IP address
2
2.Only therN T/IP
Rotary switch X1 Setting the IP address
3
3.Only therN T/IP

2019-02
12
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
2.3 Interfaces and Connections
The contact arrangements below show the front view of the plug-in area of the connectors.
Fieldbus Conne tion X01, X02
■ Connection: M12 socket, 4 pin, D-coded
■ Color coding: green
Figure 2.2 Schematic drawing of port X01, X02
Conne tion for IO-Link, digital inputs/outputs X1 - X8
■ Connection: M12 socket, 5 pin, A-coded
■ Color coding: black
Caution!
Risk of destruction!
Never route the power supply to the data cable.
Port Pin Signal Function
Ports X01, X02 1 TD+ Transmit data +
2 RD+ Receive data +
3 TD- Transmit data -
4 RD- Receive Data -
Table 2.4 Assignment of port X01, X02
1
3
2
4
Caution!
Risk of destruction with external sensor supply!
The module infeed for the sensor supply U
S
may only be provided over the specified power
connection (Power X03/X04 >> U
S
+24 V/GND_U
S
) for the module. It is not permitted to supply
external power via the IO-Port (port X1 - X8 >> pin 1/pin 3) and this may destroy the module
electronics through power feedback.
Caution!
Do not compromise galvanic isolation through incorrect cabling!
The sensor supply (port X5 - X8 >> pin 1/pin 3) and extended sensor supply (port X5 - X8 >>
pin 2/pin 5) are galvanically isolated from each other. If the reference potentials (GND_
US
– pin
3) and (GND_U
Aux
– pin 5) are connected, excessive equalization currents may flow. In this
case, it is not permitted for a sensor to be connected to (port X5 - X8 >> pin 2)!
liminating the galvanic isolation is not recommended.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
2019-02
13
Figure 2.3 Schematic drawing of inputs/outputs 1 - 8
Conne tion for Power Supply X03, X04
■ Power supply with M12 power L-coded
■ Color coding: gray
Caution!
Risk of destruction!
Never route the power supply to the data cable.
Port Pin Signal Function
IO-Link Class A,
inputs/outputs
X1 ... X4
1 L+ IO-Link sensor power supply
+24 V
2 IN-x Channel B: digital input (type
1)
3 L- IO-Link sensor power supply
GND_U
S
4 C/Q Channel A: IO-Link data
exchange
5 n.c. Not used
Port Pin Signal Function
IO-Link Class B,
inputs/outputs
X5 ... X8
1 L+ IO-Link sensor power supply
+24 V
2 U
AUX
(+24 V) Channel B: auxiliary voltage,
galvanically isolated from the
IO-Link/module power supply
3 L- IO-Link sensor power supply
GND_U
S
4 C/Q Channel A: IO-Link data
exchange
5 GND_U
AUX
Protective earth, reference
potential U
AUX
1
5
3
2
4
Note!
For the system/sensor and actuator supply, use only power supplies that comply with P LV
(protective extra-low voltage) or S LV (safety extra-low voltage). Power supplies according to
N 61558-2-6 (transformer) or N 60950-1 (switching power supplies) fulfill these
requirements.

2019-02
14
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
Figure 2.4 Schematic drawing of M12 L-encoding (plug); port X03 (IN)
Figure 2.5 Schematic drawing of M12 L-encoding (socket); port X04 (OUT)
Caution!
Loss of function when the system supply voltage is too low.
nsure in all cases that the supply voltage measured at the most remote participants
(sensor/actuator) does not drop below 18 V DC in terms of system supply voltage.
Note!
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary voltage via U
Aux
for e.g., actuators. Where the plant has a separate power
supply concept for system current and load current, this means the sensor and system area of
the thernet IO module can continue working even if there is a failure of the load power supply.
Where several thernet IO modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
Aux
.
Port Pin Signal Function
Power supply
X03, X04
1 U
S
(+24 V) Sensor/system supply
2 GND U
Aux
Ground/reference potential
U
Aux
3 GND U
S
Ground/reference potential U
s
4 U
Aux
(+24 V) Auxiliary voltage (galv.
insulated)
F (5) F (F ) Functional ground
4
1
3
2
FE
4
1
3
2
FE

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Product Description
2019-02
15
2.4 Dimensions
Figure 2.6
Figure 2.7
ICE1-8IOL-G60L-V1D
ICE1-8IOL-G30L-V1D
17.6
30.7
214.5
20
30
59.6
27 27 27 M12 x1 (10x) 27 11.5
16.5
190.3
191.8
200
M4
30
43.1
33.44.5
14
30
2914.516 29 29 M12 x1 (8x) 1813.5
215.7
217
225
M4

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Installation
2019-02
1
1 Installation
1.1 General Information
Install the module with two M6x25/30 size screws on a level surface. The required torque is
1 Nm. Use washers according to DIN 125. For the installation holes, use a spacing of
237.3 mm to 239.7 mm.
Note!
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary supply via U
Aux
for e.g., actuators. Where the plant has a separate power
supply concept for system current and load current, this means the sensor and system area of
the thernet IO module can continue working even if there is a failure of the load power supply.
Where several thernet IO modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
Aux
.
Note!
To dissipate interference currents and the MC resistance, the modules use a short circuit to
ground with an M4 thread. This is marked with the symbol for grounding and the label "X ."
Note!
Connect the module using a low-impedance connection with the reference ground. In the case
of a grounded mounting surface, you can connect the module directly via the fixing screws.
Note!
For non-grounded mounting surfaces, use a ground strap or a suitable F conductor. Connect
the ground strap or F conductor to the grounding point using an M4 screw and place a washer
and a serrated washer under the fixing screw if possible.
Note!
Use a suitable UL-certified cable (CYJV or PVVA). To program the controller, please consult the
manufacturer information and use only the appropriate accessories.
Note!
For UL application:
Approved only for indoor use. Please observe the maximum altitude of 2000 meters. Approved
up to a maximum of pollution degree 2.
Warning!
Terminals, the housing of field-wired terminal boxes or components may exceed a temperature
of 60 °C.
Warning!
Use temperature-resistant cables with the following properties:
Heat resistant up to at least 96 °C.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Commissioning, Protocol Setting
2019-02
1
1 Commissioning, Protocol Setting
1.1 Setting Protocols
Multiproto ol
You can use the multiprotocol modules to select various protocols for communication within a
fieldbus system. This allows you to integrate the multiprotocol modules into different networks
without having to obtain a specific module for each protocol. This technology also allows you to
use the same module in different environments. Using the rotary switches on the front of the
modules, you can easily and conveniently set the protocol and address of the module if the
protocol to be used supports this. Once you have selected a protocol and started the cyclical
communication, the module recognizes these settings and uses the selected protocol from this
point on. To use another supported protocol with this module, perform a factory reset.
Setting a Proto ol
Multiprotocol modules have a total of three rotary switches. Alter the switch position for the first
rotary switch X100 to set the protocol. If you use therNet/IP, set the last octet of the IP address
using the rotary switches (X100, X10, X1).
Figure 1.1 Rotary switch X100
Assigning the Proto ol Using the Rotary Swit hes
The default settings of the module do not contain any protocol settings. In this case, simply
select the desired protocol. To use a modified rotary switch setting (protocol setting), you have
to execute a power cycle or "Reset" of the web interface. Once you have set the protocol using
the rotary switches, the module saves these settings as soon as it starts a cyclical
communication. From this point, you can no longer change the protocol using the rotary switch.
To change the protocol, perform a factory reset first.
If you set the rotary coding switch to an invalid position, the device signals this with a flash
code: the BF/MS/ RR L D flashes red three times.
You can change the IP address depending on the selected protocol.
Protocol X100 X10 X1
therNet/IP 0 - 2 0 - 9 0 - 9
PROFIN T P - -
20X10X
X03
X4 X8
7X
3
X
X6
5
X1
X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
P2
P1
US
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
PN
00
X01
X4
X8
X3
X7
X6
X1
X5
X2
A B
XE
Power
IO-Link
BF DIA
X02
X01 USUAux
X03
X02
X04
A B
A B
A B
A B
A B
A B
A B
Link/Act
P
E/IP
x100
x10
x1
MS NS
R
0E/IP
PN
X100
1
2
9

2019-02
2
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Commissioning, Protocol Setting
EtherNet/IP
If you use therNet/IP as the protocol, use rotary switch X100 to set the value 100 as the last
octet of the IP address for the module. With the X100 rotary switch, you can set a value of 0 to 2
for the IP address. With the X10 and X1 rotary switches, you can set values between 0 and 9.
You can use rotary switch X10 to configure position 10 of the last octet of the IP address. With
rotary switch X1 you can configure position 1 of the last octet of the IP address.
The default setting for the first three octets of the IP address is 192.168.1.
Example: Rotary switch settings 2 (X100), 1 (X10), and 0 (X1) result in an IP address of
192.168.1.210 for therNet/IP.
PROFINET
If you use PROFIN T as the protocol, only set rotary switch X100 to the value "P."
Fa tory Settings
A factory reset erases any changes you have made to settings etc. and restores the factory
settings. The saved protocol selection is also reset.
To perform a factory reset, set rotary switch X100 to 9, rotary switch X10 to 7 and rotary switch
X1 to 9. Then switch the module off and on again. The factory settings are restored after 10
seconds.
To select a new protocol, follow the instructions in this chapter.
Figure 1.2 Restoring factory settings: X100 = 9, X10 = 7, X1 = 9
X01
X4
X8
X3
X7
X6
X1
X5
X2
A B
XE
Power
IO-Link
BF DIA
X02
X01 USUAux
X03
X02
X04
A B
A B
A B
A B
A B
A B
A B
Link/Act
P
E/IP
x100
x10
x1
MS NS
20X10X
X03
X4 X8
7X
3
X
X6
5
X1
X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
P2
P1
US
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
P
00
X100
0
E/IP
P
X10 X1
9 1
2
01
2
3
4
5
6
7
8
901
2
3
4
5
6
7
8
9
Caution!
Destruction of the Operating System
When restoring the factory settings, ensure that the module is connected to the power supply
and switched on for at least 10 seconds. If it has been on for less than 10 seconds, the
operating system may be destroyed. The module then has to be sent to Pepperl+Fuchs for
repair.

IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Commissioning for therNet/IP
2019-02
19
5 Commissioning for therNet/IP
5.1 Preparation
To configure a module in the controller, you need an DS file.
Downloading the EDS File
You can find the relevant DS file in the Software section of the product detail page for the
device.
To access the product detail page for the device, go to http://www.pepperl-fuchs.com and type
e.g., the product description or the item number into the search function.
Use the hardware or network configuration tools from your controller manufacturer to install the
DS file for the module version used. After installation, the modules can be found in the
hardware catalog as "General Purpose Discrete I/O" devices.
Reading MAC IDs
ach module has a unique, manufacturer-assigned MAC ID that cannot be changed by the
user. The assigned MAC ID is printed on the module.
Setting the Network Parameters
The IP address can be pre-set using the three rotary switches on the front side of the modules.
Please note that a fixed IP address is required to use QuickConnect.
Once the power supply has been restored, the modules read in the switch positions. The
selected operating mode overwrites the saved settings.
The devices support the DHCP and BOOTP protocols for receiving the required network
parameters such as IP address and subnet mask.
The factory settings of the static network parameters are:
■ IP address: 192.168.001.001
■ Subnet mask: 255.255.255.000
■ Gateway address: 000.000.000.000
The following settings are possible via the rotary coding switches:
Rotary switch position Function
000
(As delivered)
The DHCP and BOOTP functionality is
activated as standard on delivery. The network
parameters are initially requested using DHCP
requests. If this is not successful, the request
is made using BOOTP requests. The network
parameters are not saved; however, it is
possible to save them via the integrated web
server.
000
(Network parameters already saved)
The last-saved network parameters are used
(IP address, subnet mask, gateway address,
DHCP on/off, BOOTP on/off).
001 to 254 The last three digits of the saved or default IP
address are overwritten by the control switch
setting.
979 The device performs a reset to factory
settings. The network parameters are also
reset to the default values. Communication is
not possible in this operating mode.

2019-02
20
IC 1-8IOL-G60L-V1D, IC 1-8IOL-G30L-V1D
Commissioning for therNet/IP
5.2 Configuration xample
Configuration with RSLogix5000
The configuration and commissioning procedure for modules that is described on the following
pages is based on the RSLogix5000 software from Rockwell Automation. When using a control
system from a different provider, please refer to the corresponding documentation.
1. Install the DS files for the modules in RSLogix5000 using the DS hardware installation tool
in the "Tools" menu.
2. Select the correct controller.
3. Select the "New Module" menu item. The following selection window opens:
4. On the right-hand side in "Module Type Vendor Filters," select the option "Pepperl + Fuchs"
to view all installed modules from Pepperl+Fuchs.
5. Select the module you want to add and click the "Create" button.