Pepperl+Fuchs ICE11-8IOL-G60L-V1D User manual

ICE11-8IOL-G60L-V1D
Fieldbus Module with
Multiprotocol Tech ology a d IO-Li k
CC-Li k
EtherCAT
EtherNet/IP
Modbus
PROFINET
Ma ual

With regard to the supply of products, the current issue of the following document is applicable:
The General Terms of Delivery for Products and Services of the Electrical ndustry, published
by the Central Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elek-
troindustrie (ZVE ) e.V.) in its most recent version as well as the supplementary clause:
"Expanded reservation of proprietorship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [email protected]perl-fuchs.com
North America Headquarters
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [e-mail]
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [e-mail]
https://www.pepperl-fuchs.com

CE11-8 OL-G60L-V1D
Contents
2024-01
3
1 I troductio ................................................................................................................ 6
1.1 Co te t of this Docume t............................................................................. 6
1.2 Ma ufacturer .................................................................................................. 6
1.3 Target Group, Perso el ............................................................................... 6
1.4 Symbols Used ................................................................................................ 7
2 Cybersecurity I formatio ........................................................................................ 8
3 Product Descriptio ................................................................................................10
3.1 Use a d Applicatio ....................................................................................10
3.2 I dicators a d Operati g Eleme ts........................................................... 12
3.3 I terfaces a d Co ectio s .......................................................................17
3.4 Dime sio s...................................................................................................20
4 I stallatio ................................................................................................................ 21
4.1 Ge eral I formatio ..................................................................................... 21
5 Commissio i g, Protocol Setti g..........................................................................23
5.1 MAC Addresses ...........................................................................................23
5.2 Assig i g the Device Name to a PROFINET IO Module...........................23
5.3 IODD..............................................................................................................25
5.4 Protocol Setti g ........................................................................................... 25
6 Commissio i g with CC-Li k.................................................................................30
6.1 Preparatio ...................................................................................................30
6.2 Co figuratio of CC-Li k IE Field Basic....................................................30
6.3 Process Data Assig me t ..........................................................................40
6.4 Co figuratio a d Operatio with GxWorks®.......................................... 41
7 Commissio i g for EtherCAT .................................................................................45
7.1 EtherCAT.......................................................................................................45
7.2 Preparatio ...................................................................................................45
7.3 Co figuratio ............................................................................................... 45
7.3.1 Configuration .................................................................................................................... 46
7.3.2 Device Parameters ........................................................................................................... 50
7.3.3 Configuration Example with TwinCAT® 3.......................................................................... 64
7.4 Firmware Update..........................................................................................69

CE11-8 OL-G60L-V1D
Contents
2024-01
4
8 Commissio i g for EtherNet/IP..............................................................................72
8.1 Co figuratio ................................................................................................72
8.2 Co figuratio Parameters...........................................................................74
8.3 Process Data Assig me t...........................................................................86
8.4 Co figuratio a d Operatio
with Rockwell Automatio Studio 5000®..................................................96
8.5 CIP Object Classes ....................................................................................107
8.5.1 EtherNet/ P Object Classes ............................................................................................ 107
8.5.2 Manufacturer-Specific Object Classes............................................................................ 117
8.5.3 "Message" Configuration in Rockwell Automation Studio 5000®.................................... 124
9 Commissio i g with Modbus...............................................................................126
9.1 Preparatio .................................................................................................126
9.2 Co figuratio ..............................................................................................127
9.3 Process Data Assig me t.........................................................................136
10 Commissio i g for PROFINET .............................................................................139
10.1 Preparatio .................................................................................................139
10.2 Co figuratio Example..............................................................................139
10.2.1 ntegration of PROF NET O Modules in the T A Portal ................................................... 140
10.2.2 Assignment of a Device Name and P Address............................................................... 141
10.2.3 Configuring the O-Link Channels ................................................................................... 143
10.2.4 Parameterization of the Status/Control Module............................................................... 146
10.2.5 Parameterization of O-Link Channels X1– X8 ................................................................ 149
10.2.6 O-Link Device Parameterization..................................................................................... 157
10.2.7 Media Redundancy Protocol (MRP) ............................................................................... 168
10.2.8 Replacing Devices without a Removable Medium/Programming Unit............................. 169
10.2.9 dentification and Maintenance Functions ( &M) ............................................................. 170
10.2.10 Prioritized Start-Up/Fast Start-Up (FSU) ......................................................................... 177
10.2.11 "Suspend/Resume" of the O-Link Port Control............................................................... 179
10.3 Bit Assig me t...........................................................................................185
11 The I tegrated Web Server ...................................................................................189
12 IIoT Fu ctio ality ...................................................................................................196
12.1 MQTT ...........................................................................................................196
12.2 OPC UA .......................................................................................................206
12.3 REST API.....................................................................................................210
12.4 CoAP Server ...............................................................................................221
12.5 Syslog .........................................................................................................225
12.6 NTP ..............................................................................................................228

CE11-8 OL-G60L-V1D
Contents
2024-01
5
13 Troubleshooti g.....................................................................................................231
13.1 Diag ostics I dicator i the I tegrated Web Server .............................. 231
13.2 Diag ostic Processi g via CC-Li k .........................................................231
13.3 Alarm Sig als a d Error Messages from Modules via EtherCAT .........234
13.4 Diag ostic Processi g via EtherNet/IP ...................................................236
13.5 Diag ostic Processi g via Modbus .........................................................239
13.6 Alarm Sig als a d Error Messages from Modules via PROFINET........245

2024-01
6
CE11-8 OL-G60L-V1D
ntroduction
1 I troductio
1.1 Co te t of this Docume t
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
n addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•nstruction manual
•Functional safety manual
•Other documents
1.2 Ma ufacturer
1.3 Target Group, Perso el
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product. The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the nternet at
www.pepperl-fuchs.com.
Note
For specific device information such as the year of construction, scan the QR code
on the device. As an alternative, enter the serial number in the serial number search
at www.pepperl-fuchs.com.
Pepperl+Fuchs Group
Lilienthalstraße 200, 68307 Mannheim, Germany
nternet: www.pepperl-fuchs.com

CE11-8 OL-G60L-V1D
ntroduction
2024-01
7
1.4 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
War i g Messages
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
I formative Symbols
Actio
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Da ger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
War i g!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Cautio !
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

2024-01
8
CE11-8 OL-G60L-V1D
Cybersecurity nformation
2 Cybersecurity I formatio
The CE11-8 OL-G60L-V1D is secure for the area of application defined here in accordance
with EC 62443-4-1. The operator must implement the measures defined in this section to
ensure the secure operation and protection of the device while online.
Security Co text
The CE11-8 OL-G60L-V1D is intended for use in an automation network. This is a secure net-
work with known and trusted participants that is separated (physically or logically) from the
company network.
A firewall must be configured so that only defined ports are forwarded to other subnets.
The device uses the following ports:
•Ports 49152, 34964 for PROF NET
•Port 2222 and port 44818 for EtherNet/ P
•Port 68 DHCP client
•Port 80 for the administration website using HTTPS
•Port 1883 (factory default, changeable) for MQTT if enabled
•Port 4840 (factory default, changeable) for OPC UA if enabled
•Port 514 (factory default, changeable) for syslog if enabled
•Port 5683 for CoAP if enabled
To avoid losing packets, we recommend limiting the network load to < 5 % of the bandwidth.
We recommend operating the gateway behind a network switch.
The device must be physically secured against unauthorized access and operated in a lock-
able switch cabinet or room that is only accessible to authorized personnel. Otherwise, there is
a risk that some of the device settings can be changed via the "X3" service interface and the
password
1
printed on the gateway.
The device contributes to the "defense-in-depth" strategy with the following security functions:
1. if left unchanged
Security fu ctio Addressed threat
Access control with single-factor authentica-
tion (SFA) and automatic time-based login
lock in the event of incorrect authentication.
Protection against unauthorized access,
brute-force attacks.
Deletion of all information stored in the device
using the "Reset to factory settings" function. Protection against information being subject to spying by physical access to the device after
decommissioning and disposal by the system
operator.
The access data is hashed by the SHA1 cryp-
tographic hash function with salt and pepper. Protection against reading and recalculation of a password or finding a collision, e.g., with
"Rainbow table."
Even in the unlikely event that this would be
possible, this would have to be repeated for
each individual device, since results cannot
be transferred to other devices, even if the
same password is used.

CE11-8 OL-G60L-V1D
Cybersecurity nformation
2024-01
9
The Followi g Measures Must Be Impleme ted o the Device for
Commissio i g:
The Followi g Setti gs Must Be Impleme ted o the Device for
Operatio :
The Followi g Measures Must Be Impleme ted o the Device for
Decommissio i g:
Requireme ts for User Roles to E sure Cybersecure Operatio
User Accou t Privileges a d Rights
•Hardening:
Change the device-specific password printed on the device.
•Special security
functions:
Access control with single factor authentication (SFA)
Automatic login lock if access data is entered incorrectly after the sev-
enth attempt for a duration of 1 minute to protect against brute-force
attacks.
The access data is hashed multiple times by the SHA1 cryptographic
hash function with salt and pepper.
KeePass password manager for generating and storing passwords.
•Additional security
layers:
Password change: every 2 years.
•Servicing and man-
agement:
Check the website regularly for the release of security advisories and
subscribe to the RSS feed: https://www.pepperl-
fuchs.com/global/en/29079.htm.
•User access data:
Delete using the "Reset to factory settings" function.
•Configuration:
Delete using the "Reset to factory settings" function.
•Log data (history,
historical data, and
error data):
Stored only temporarily and deleted after a restart.
•Administrator:
mplement the measures defined in "The following measures must be
implemented on the device for operation."
f applicable: Update the firmware and install security patches.
•Administrator:
Switching functions on and off
Configuration
Reset to factory settings
Read the log and device status
Firmware updates

2024-01
10
CE11-8 OL-G60L-V1D
Product Description
3 Product Descriptio
3.1 Use a d Applicatio
The module is a multiprotocol fieldbus module with 8 type A O-Link master ports according to
O-Link standard V1.1.3.
The G60L design in fully cast metal housing is resistant to mechanical damage and environ-
mental influences. The G60L has protection class P65/ P67.
The fieldbus module serves as an interface between the controller of a fieldbus system and the
field level. Due to its multiprotocol capability, the fieldbus module supports the Ethernet com-
munication protocols PROF NET, EtherNet/ P, EtherCAT, CC-Link, and MODBUS TCP.
An L-coded M12 connector plug used for supplying power enables a current rating of up to 2 x
16 A. The inputs and outputs are equipped with A-coded M12 connector plugs. Connection to
the fieldbus is achieved using a D-coded M12 connector plug.
The communication protocols are configured either manually via a rotary switch or automati-
cally. The diagnostics display status information for each channel via LEDs. An integrated web
server enables access to the fieldbus module. nformation regarding the status of the module is
also displayed and network parameters such as the P address and subnet mask can be con-
figured.
Multiprotocol (PROFINET, EtherNet/IP, EtherCAT®, MODBUS TCP,
CCLi k IE Field Basic)
The multiprotocol modules allow you to select different protocols for communication within a
fieldbus system. As a result, multiprotocol modules can be integrated into different networks
without the need to obtain specific modules for each protocol. Thanks to this technology, you
can also use one module in different environments.
Using rotary coding switches in the lower area of the modules, you can conveniently and easily
set both the protocol and the address of the module, provided that the protocol to be used sup-
ports this. f you have chosen a protocol and started the cyclic communication once, the mod-
ule remembers this setting and uses the selected protocol from this point on. To use another
supported protocol with this module, perform a factory reset.
I put/Output Cha els for the Field Level
For the field level, the modules have the following input/output channels
•8 x O-Link Master Ports Class A
f one or more of the O-Link ports are not required, these can also be freely configured as digi-
tal inputs or outputs (S O mode).
IO-Li k Characteristics of the Modules
The modules support O-Link Standard V1.1.3.
•Parametrization of O-Link devices in PROF NET using Siemens O_L NK_DEV CE func-
tion blocks for Step 7 and the T A Portal
8 x O-Link master ports
•8 class A connections with additional freely configurable digital input/outputs at pin 2 of
the /O port
O-Link connections
•4-pin M12 connector
Parameter storage
•The Parameter Storage function stores and monitors the parameters of the O-Link device
and the O-Link master.

CE11-8 OL-G60L-V1D
Product Description
2024-01
11
•This function makes it possible for you to easily replace the O-Link device or the O-Link
master.
This is possible from O-Link specification V1.1 onward and only if the O-Link device and
the O-Link master support the function.
O-Link device parameterization
•The O-Link devices can be parameterized in the PROF NET protocol using the Siemens
O_L NK_DEV CE function block for STEP 7 and the T A Portal.
Special Product Features
•Rugged desig :
Connectivity options for the module series include the widespread M12 connector with A
coding for /O signals and D coding for the network. n addition, the connectors are color-
coded to prevent users from using the wrong ports.
•I tegrated web server:
Network parameters such as P address, subnet mask, and gateway can be adjusted via
the integrated web server. The modules support the communication protocols BOOTP
and DHCP for automated assignment of network parameters via the corresponding serv-
ers.
You can read the parameters of the O-Link device via the integrated web server and write
new parameters to the modules in single-write mode. Single-write mode does not activate
the automatic parameter storage mechanism.
•Force Mode
n Force Mode, the module ports can be configured as digital inputs/outputs or O-Link
ports.
"Force Mode" allows the simulation of process data at the digital inputs/outputs without
the need to connect sensors and actuators. This means that you can test an application in
advance without a full physical application. t is possible to simulate input switching states
or to switch outputs even without a controller. This feature makes machine commissioning
simpler and quicker and can be used to test new production plants.
•I tegrated etwork switch:
The integrated two-port Ethernet switch of the modules allows you to set up a line topol-
ogy or a ring topology for the EtherNet/ P network or PROF NET network. The additional
DLR or MRP protocol allows you to design a highly available network infrastructure.
•Redu da cy fu ctio :
The module firmware supports the redundancy function DLR (Device Level Ring) or MRP
(Media Redundancy Protocol) for ring topologies. This means that if the connection is
interrupted, the modules switch immediately to an alternative ring segment and therefore
ensure interruption-free operation. The supported DLR class is "beacon-based" in accor-
dance with the EtherNet/ P specification.
•Fail-safe fu ctio :
The modules provide a fail-safe function. You can therefore choose the behavior of each
individual output channel in the event of an interruption or a loss of communication.
•QuickCo ect:
QuickConnect allows the modules to record the communication in an EtherNet/ P network
especially quickly through an accelerated boot-up process. This allows you to switch tools
faster, for example.

2024-01
12
CE11-8 OL-G60L-V1D
Product Description
3.2 I dicators a d Operati g Eleme ts
(1) Channel indicator LED
(2) Status indicator LED
(3) Rotary switch
20X10X
X03
X4 X8
7X3X
X6
5
X1X
X2
A
B
XE
X04
DIA
MS
BF
NS
FM
Link/Act
X02 ERRRUN
X01
US
UL
A
B
A
B
A
B
x100 x10 x1
0E/IP
PN
00
EC
MC
CC
1
2
3
Note
The LEDs in the lower area of the Ethernet O module have different names and functions
depending on the selected protocol. The following LED descriptions are therefore divided into
a general part (1), which is valid for all protocol settings, and LED descriptions for a specific
protocol setting (2).
Figure 3.1
1
2
X4 X8
DIA
MS
BF
NS
FM
Link/Act
X02 ERRRUN
X01
US
UL
A
B
x100 x10 x1
0E/IP
PN
00
EC
MC
CC

CE11-8 OL-G60L-V1D
Product Description
2024-01
13
I dicators - Ge eral Part
Description for LED A, B, D A, U
L
, U
S
LED Fu ctio
U
L1
1. AUX
Green: Auxiliary sensor/actuator voltage OK
•18 V (± 1 V) < U
L
< 30 V (± 1 V)
Red
2
: Auxiliary sensor/actuator voltage too low or too high
•U
L
< 18 V (± 1 V) or U
L
> 30 V (± 1 V)
Off: No auxiliary sensor/actuator voltage
2. f "Report U
L
supply voltage fault" is enabled
U
S
Green: System/sensor voltage OK
•18 V (± 1 V) < U
S
< 30 V (± 1 V)
Red: System/sensor voltage too low or too high
•U
S
< 18 V (± 1 V) or U
S
> 30 V (± 1 V)
Red flashing: The device is reset to its factory settings
Off: No system/sensor voltage
A
3
3. X1– X8
Green: O-Link-COM-Mode
•O-Link communication present
Green flashing: O-Link-COM-Mode
•No O-Link communication
Yellow: Standard /O mode
•Status of the digital input or output at C/Q
Off: None of the states described above
B
3<Default ¬¹ Font>
White: Status of digital input and digital output at pin 2 "On"
Red
•Overload or short-circuit at pin 4 and pin 2
•All modes: Overload or short-circuit at line L+ (pin 1)
•Communication errors
Off: One of the states described above.
FM Blue: "Force Mode" active
Lnk/Act X01
Lnk/Act X02 Green: Connected to an Ethernet node Yellow flashing: Ethernet node data exchange
Off: No connection
Table 3.1

2024-01
14
CE11-8 OL-G60L-V1D
Product Description
EtherNet/IP I dicators
E/ P area: relevant LEDs Lnk/Act X01, Lnk/Act X02, MS, NS
PROFINET I dicators
P area: relevant LEDs Lnk/Act X01, Lnk/Act X02, BF, D A
LED Fu ctio
BF Red: No configuration, slow or no physical connection
Red flashing: Link exists but no communication link to the Ethernet/ P
controller is available
Off: No error
D A Red: Ethernet/ P diagnostic alarm active
Red flashing (1 Hz): Time-out or FailSafe mode is active
Red flashing (2 Hz) for 3 s: DCP signal service is triggered via the bus
Red double flashing: Firmware Update
Off: No error
MS Green: Module ready for operation
Green flashing: Configuration missing
Red/green flashing: Self-test
Red: Non-recoverable, serious error
Flashing red: Minor recoverable error (e.g., incorrect configuration)
Off: Module is powered down
NS Green: Module has at least one existing connection
Green flashing: Module has no existing connections. P address is
available
Red/green: Module is performing a self-test
Red: Module has determined that the assigned P address already
exists
Red flashing: The connection has timed out or been interrupted
Off: Module is turned off or does not have an P address.
Table 3.2
LED Fu ctio
BF Red: No configuration, slow or no physical connection
Red flashing: Link exists but no communication link to the PROF NET
controller is available
Off: No error
D A Red: Ethernet/ P diagnostic alarm active
Red flashing (1 Hz): Time-out or FailSafe mode is active
Red flashing (2 Hz) for 3 s: DCP signal service is triggered via the bus
Red double flashing: Firmware Update
Off: No error
MS Green: Module ready for operation
Green flashing: Configuration missing
Red/green flashing: Self-test
Red: Non-recoverable, serious error
Flashing red: Minor recoverable error (e.g., incorrect configuration)
Off: Module is powered down
NS Green: Module has at least one existing connection
Green flashing: Module has no existing connections. P address is
available
Red/green: Module is performing a self-test
Red: Module has determined that the assigned P address already
exists
Red flashing: The connection has timed out or been interrupted
Off: Module is turned off or does not have an P address.
Table 3.3

CE11-8 OL-G60L-V1D
Product Description
2024-01
15
EtherCAT I dicators
EC area: relevant LEDs Lnk/Act X01, Lnk/Act X02, BF, D A
LED Fu ctio
BF Red: No configuration, slow or no physical connection
Red flashing: Link exists but no communication link to the EtherCAT
controller is available
Off: EtherCAT control has established an active connection to the
deviceNo error
D A Red: Ethernet/ P diagnostic alarm active
Red flashing (1 Hz): Time-out or FailSafe mode is active
Red flashing (2 Hz) for 3 s: DCP signal service is triggered via the bus
Red double flashing: Firmware Update
Off: No error
MS Green: Module ready for operation
Green flashing: Configuration missing
Red/green flashing: Self-test
Red: Non-recoverable, serious error
Flashing red: Minor recoverable error (e.g., incorrect configuration)
Off: Module is powered down
NS Green: Module has at least one existing connection
Green flashing: Module has no existing connections. P address is
available
Red/green: Module is performing a self-test
Red: Module has determined that the assigned P address already
exists
Red flashing: The connection has timed out or been interrupted
Off: Module is turned off or does not have an P address.
Table 3.4

2024-01
16
CE11-8 OL-G60L-V1D
Product Description
Modbus I dicators
MB area: relevant LEDs BF, D A
CC-Li k I dicators
CC area: relevant LEDs BF, D A
LED Fu ctio
BF Red: Bus fault, no configuration, no or slow phys. connection
Red flashing (2 Hz): Link present, but no communication connection
to the Modbus-TCP controller
Off: Modbus-TCP control has established an active connection to the
device
D A Red: Ethernet/ P diagnostic alarm active
Red flashing (1 Hz): Time-out or FailSafe mode is active
Red flashing (2 Hz) for 3 s: DCP signal service is triggered via the bus
Red double flashing: Firmware Update
Off: No error
MS Green: Module ready for operation
Green flashing: Configuration missing
Red/green flashing: Self-test
Red: Non-recoverable, serious error
Flashing red: Minor recoverable error (e.g., incorrect configuration)
Off: Module is powered down
NS Green: Module has at least one existing connection
Green flashing: Module has no existing connections. P address is
available
Red/green: Module is performing a self-test
Red: Module has determined that the assigned P address already
exists
Red flashing: The connection has timed out or been interrupted
Off: Module is turned off or does not have an P address.
Table 3.5
LED Fu ctio
BF Red: Bus fault, no configuration, no or slow phys. connection
Red flashing (2 Hz): Link present, but no communication connection
to the CC-Link E controller
Off: CC-Link E control has established an active connection to the
device
D A Red: CC-Link E diagnostic alarm active
Red flashing (1 Hz): Time-out or FailSafe mode is active
Red flashing (2 Hz) for 3 s: DCP signal service is triggered via the bus
Red double flashing: Firmware Update
Off: No error
MS Green: Module ready for operation
Green flashing: Configuration missing
Red/green flashing: Self-test
Red: Non-recoverable, serious error
Flashing red: Minor recoverable error (e.g., incorrect configuration)
Off: Module is powered down
NS Green: Module has at least one existing connection
Green flashing: Module has no existing connections. P address is
available
Red/green: Module is performing a self-test
Red: Module has determined that the assigned P address already
exists
Red flashing: The connection has timed out or been interrupted
Off: Module is turned off or does not have an P address.
Table 3.6

CE11-8 OL-G60L-V1D
Product Description
2024-01
17
Operati g Eleme ts
3.3 I terfaces a d Co ectio s
The contact arrangements below show the front view of the plug-in area of the connectors.
Fieldbus Co ectio X01, X02
•Connection: M12 socket, 4-pin, D-coded
•Color coding: green
Figure 3.2 Schematic drawing of port X01, X02
Switch Fu ctio
Rotary switch X100 Setting the fieldbus protocol
Setting the P address
1
1. Only EtherNET/ P
Rotary switch X10 Setting the P address
Rotary switch X1 Setting the P address
Cautio !
Risk of destruction!
Never route the power supply to the data cable.
Port Pi Sig al Fu ctio
Ports X01, X02 1 TD+ Transmit data +
2 RD+ Receive data +
3 TD- Transmit data -
4 RD- Receive data -
Table 3.7 Assignment of port X01, X02
1
3
2
4

2024-01
18
CE11-8 OL-G60L-V1D
Product Description
Co ectio for IO-Li k, Digital I puts/Outputs X1 ... X8
•Connection: M12 socket, 5-pin, A-coded
•Color coding: black
Figure 3.3 Schematic drawing of inputs/outputs 1–8
Co ectio for Power Supply X03, X04
•Power supply with M12 power L-coded
•Color coding: gray
Cautio !
Risk of destruction with external sensor supply!
The module infeed for the sensor supply U
S
may only be provided over the specified power
connection (Power X03/X04 >> U
S
+24 V/GND_U
S
) for the module. t is not permitted to supply
external power via the O-Port (port X1–X8 >> pin 1/pin 3) and this may destroy the module
electronics through power feedback.
Cautio !
Risk of destruction!
Never route the power supply to the data cable.
Port Pi Sig al Fu ctio
O-Link Class A, inputs/outputs
X1 ... X8 1 L+ O-Link sensor power supply +24 V
2 N-x Channel B: digital input (type 1)
3 L- O-Link sensor power supply GND_U
S
4 C/Q Channel A: O-Link data exchange
5 n.c. not assigned
1
5
3
2
4
Note
For the system/sensor and actuator supply, use only power supplies that comply with PELV
(protective extra-low voltage) or SELV (safety extra-low voltage). Power supplies according to
EN 61558-2-6 (transformer) or EN 60950-1 (switching power supplies) fulfill these
requirements.
Cautio !
Loss of function when the system supply voltage is too low.
Ensure in all cases that the supply voltage measured at the most remote node (sensor/actua-
tor) does not drop below 18 V DC in terms of system supply voltage.

CE11-8 OL-G60L-V1D
Product Description
2024-01
19
Figure 3.4 Schematic drawing of M12 L-encoding (plug); port X03 ( N)
Figure 3.5 Schematic drawing of M12 L-encoding (socket); port X04 (OUT)
Note
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary voltage via U
S
for actuators, for example. Where the plant has a separate
power supply concept for system current and load current, this means the sensor and system
area of the Ethernet O module can continue working even if there is a failure of the load power
supply.
Where several Ethernet O modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
L
.
The O-Link specification requires at least 20 V at the output supply of the /O ports L+
1
. A
minimum of 21 V is required at the power supply U
S
for the O-Link master to minimize the risk
of internal voltage drops in the O-Link master.
1. Pin 1
Port Pi Sig al Fu ctio
Voltage supply
X03, X04 1 U
S
(+24 V) Sensor/system supply
2 GND U
L
Ground/reference potential U
^L
3 GND U
S
Ground/reference potential U
S
4 U
L
(+24 V) Auxiliary voltage
FE (5) FE (FE) Functional earth
4
1
3
2
FE
4
1
3
2
FE

2024-01
20
CE11-8 OL-G60L-V1D
Product Description
3.4 Dime sio s
Figure 3.6
17.6
30.7
214.5
20
30
59.6
27 27 27 M12 x1 (10x) 27 11.5
16.5
190.3
191.8
200
M4