Pepperl+Fuchs IUT-F190-R4-V1 Series User manual

IUH-F190-V1-*
IUT-F190-R4-V1*
UHR Read/Write Head
for IDENTControl
FACTORY AUTO ATION
ANUAL

With regard to the supply of products, the current issue of the following document is ap-
plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-
try, published by the Central Association of the lectrical Industry (Zentralverband
lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the
supplementary clause: " xpanded reservation of proprietorship"
IUH-F190-V1-*, IUT-F190-R4-V1*

IUH-F190-V1-*, IUT-F190-R4-V1*
3
1 Introduction................................................................................. 7
1.1 Content of this Document ................................................................... 7
1.2 Target Group, Personnel...................................................................... 7
1.3 Symbols Used ...................................................................................... 8
2 Certificates and Approvals ........................................................ 9
2.1 Declaration of Conformity (RE Directive 2014/53/EU)...................... 9
2.2 FCC-Information................................................................................... 9
2.3 IC-Information..................................................................................... 10
2.4 UL Information.................................................................................... 10
2.5 Additional Country-Specific Approvals ........................................... 10
3 Product Description ................................................................. 11
3.1 RFID Frequency Bands...................................................................... 11
3.2 UHF general ........................................................................................ 11
3.2.1 Advantages of UHF.......................................................................... 11
3.2.2 Applications for UHF Systems ......................................................... 11
3.2.3 Memory Structure of a Tag acc. to PC Gen 2 ................................. 12
3.2.4 lectronic Product Code ( PC)........................................................ 14
3.2.5 Influence of Various Materials on the Sensing Range ...................... 14
3.2.6 Dense Reader Mode (DRM) ............................................................ 15
3.2.7 Frequency Hopping Spread Spectrum............................................. 16
3.2.8 Relevant Standards for UHF............................................................. 17

4
IUH-F190-V1-*, IUT-F190-R4-V1*
3.3 Countries of Use.................................................................................17
3.3.1 uropean Union ............................................................................... 17
3.3.2 Argentina.......................................................................................... 18
3.3.3 Australia ........................................................................................... 18
3.3.4 Brazil ................................................................................................ 18
3.3.5 Canada ............................................................................................ 18
3.3.6 China................................................................................................ 18
3.3.7 Hong Kong .......................................................................................19
3.3.8 India ................................................................................................. 19
3.3.9 Japan ............................................................................................... 19
3.3.10 Colombia.......................................................................................... 19
3.3.11 Malaysia ........................................................................................... 19
3.3.12 Mexico.............................................................................................. 20
3.3.13 New Zealand .................................................................................... 20
3.3.14 Russia .............................................................................................. 20
3.3.15 Singapore......................................................................................... 20
3.3.16 South Korea .....................................................................................21
3.3.17 Thailand ........................................................................................... 21
3.3.18 United States of America .................................................................. 22
3.3.19 Vietnam ............................................................................................ 22
3.4 General Functions and Features .......................................................23
3.5 Indicators and Operating Elements..................................................24
3.6 Connection..........................................................................................24
3.7 Scope of Delivery ...............................................................................25
3.8 Accessories ........................................................................................25
3.8.1 ID NTControl...................................................................................25
3.8.2 Read/Write Tags............................................................................... 26
3.8.3 Connection Cable for R/W Heads and Trigger Sensors.................... 26
3.8.4 Cable Connectors for the Power Supply...........................................27
3.8.5 Mounting Set .................................................................................... 27
4 Installation................................................................................. 28
4.1 Storage and Transport .......................................................................28
4.2 Unpacking ...........................................................................................28

IUH-F190-V1-*, IUT-F190-R4-V1*
5
4.3 ounting ............................................................................................. 28
4.3.1 Room Orientation............................................................................. 29
4.3.2 Minimum Distances ......................................................................... 30
4.3.3 Polarization ...................................................................................... 30
4.4 Connection ......................................................................................... 31
4.5 E C Concept...................................................................................... 32
5 Commissioning......................................................................... 33
5.1 Definitions........................................................................................... 33
5.1.1 Display............................................................................................. 33
5.1.2 Legend............................................................................................. 33
5.2 Sensor Settings.................................................................................. 34
5.3 Operation via the Command Interface ............................................. 34
6 Operation................................................................................... 37
6.1 General ................................................................................................ 37
6.2 Basic Command Process .................................................................. 37
6.3 Command Overview .......................................................................... 38
6.4 Read/Write Commands...................................................................... 39
6.5 Filter Commands................................................................................ 44
6.6 Configuration Commands ................................................................. 47
6.6.1 Read and Write Parameters ............................................................. 48
6.6.2 Parameters ...................................................................................... 49
6.7 Read/Write Head with Integrated RS-485 Interface ........................ 60
6.7.1 Single-Drop Mode............................................................................ 60
6.7.2 Multi-Drop Mode.............................................................................. 61
6.8 Error/Status essages ...................................................................... 63

6
IUH-F190-V1-*, IUT-F190-R4-V1*
7 Service and aintenance ........................................................ 65
8 Troubleshooting........................................................................ 66
9 Appendix ................................................................................... 67
9.1 Dimensions .........................................................................................67
9.2 ASCII Table ..........................................................................................67
9.3 Detection Range .................................................................................68

IUH-F190-V1-*, IUT-F190-R4-V1*
Introduction
2017-12
7
1 Introduction
1.1 Content of this Document
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
■ Product identification
■ Delivery, transport, and storage
■ Mounting and installation
■ Commissioning and operation
■ Maintenance and repair
■ Troubleshooting
■ Dismounting
■ Disposal
The documentation comprises the following parts:
■ This document
■ Datasheet
In addition, the documentation may comprise the following parts, if applicable:
■ U-type examination certificate
■ U declaration of conformity
■ Attestation of conformity
■ Certificates
■ Control drawings
■ Instruction manual
■ Other documents
1.2 Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and
dismounting lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation,
commissioning, operation, maintenance, and dismounting of the product. The personnel must
have read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note!
Visit www.pepperl-fuchs.com to access further documentation for full information about the
product.

2017-12
8
IUH-F190-V1-*, IUT-F190-R4-V1*
Introduction
1.3 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Warning essages
You will find warning messages, whenever dangers may arise from your actions. It is mandatory
that you observe these warning messages for your personal safety and in order to avoid
property damage.
Depending on the risk level, the warning messages are displayed in descending order as
follows:
Informative Symbols
Action
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note!
This symbol brings important information to your attention.

IUH-F190-V1-*, IUT-F190-R4-V1*
Certificates and Approvals
2017-12
9
2 Certificates and Approvals
2.1 Declaration of Conformity (R Directive 2014/53/ U)
This product was developed and manufactured under observance of the applicable uropean
standards and guidelines.
The product manufacturer, Pepperl+Fuchs GmbH, 68307 Mannheim, has a certified quality
assurance system that conforms to ISO 9001.
2.2 FCC-Information
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
FCC Notice
To comply with FCC part 15 rules in the United States, the system must be professionally
installed to ensure compliance with the Part 15 certification. It is the responsibility of the
operator and professional installer to ensure that only certified systems are deployed in the
United States. The use of the system in any other combination (such as co-located antennas
transmitting the same information) is expressly forbidden.
FCC Exposure Information
To comply with FCC RF exposure compliance requirements, the antennas used for this
transmitter must be installed to provide a separation distance of at least 30 cm from all persons
and must not be co-located or operated in conjunction with any other antenna or transmitter.
Note!
A Declaration of Conformity can be requested from the manufacturer or downloaded from
www.pepperl-fuchs.com.
ISO9001
FCC ID: IREIUHF190V1B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation.
Attention:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

2017-12
10
IUH-F190-V1-*, IUT-F190-R4-V1*
Certificates and Approvals
2.3 IC-Information
IC Exposure Information
To comply with IC RF exposure compliance requirements, the antennas used for this
transmitter must be installed to provide a separation distance of at least 30 cm from all persons
and must not be co-located or operated in conjunction with any other antenna or transmitter.
2.4 UL Information
Technical Data and Environmental Conditions
This device is for indoor use only.
This device may be operated in altitudes up to 2000 m.
The ambient temperature range is from -20 °C to +70 °C for operation with non-transmission
periods, or -20 °C to +60 °C for continuous transmission mode.
The maximum relative humidity is 80 % for temperatures up to 31 °C decreasing linearly to 50%
relative humidity at 40 °C.
Nominal power supply voltage is 24 V
DC
, voltage range is 20 ... 30 V
DC
. Supply must be P LV
(Protective xtra Low Voltage). This is the case if Pepperl+Fuchs ID NTControl control
interface is used.
Protection class IP67 is not included in the UL approval. The protection class is tested by
Pepperl + Fuchs GmbH.
2.5 Additional Country-Specific Approvals
For all current approvals see the data sheet of your read / write head under www.pepperl-
fuchs.com.
This device complies with Industry Canada licence-exempt RSS standard(s) and with part 15
of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-
lage est susceptible d'en compromettre le fonctionnement.