Petsafe Staywell 400EF User manual

4-Way Locking
Cat Flap
Magnetic
Before installing your cat flap, please read the following step-by-step instructions carefully
Installation Guide for Metal Door (Wood Door Installation on Reverse)
1 2 3
248 mm
(9
3
/ 4 ")
165 mm
(6
1
/ 2 ")
4
Tools Required Measure the belly height of your cat.
This is usually around 4 to 6 inches.
Mark this measurement on the outside
of your door and draw a straight
horizontal line 6
1/2"
.
Wood Door Installation on reverse.
The cat flap will not operate if fitted to a door
containing metal e.g. uPVC coated metal doors,
metal skin doors, or security doors.The cat flap
must be isolated from the metal with a piece of
wood. Draw a square 6
1
/
2
" W x 9
3
/
4
" H.
Bottom of square should be the horizontal
line from step 3.
5
Drill holes at each corner.
6 7 8
Cut along the lines using a jigsaw. Smooth out the rough edges. Fit a 3
1/2"
x 6
1/2"
wooden block to
the hole.
9 10 11
Screw into place. Cut off
excess screw with wire cutters. Cover screw
holes with blanking plugs for neat finish.
Push fit 4-way locking handle into place.
12
Place the cat flap in the hole, with the
red 4-way lock facing inside. Mark the
screw holes.
Remove the cat flap and drill holes
with a
3/16"
drill bit.
The fixed tunnel is an integral part of
the mechanism and must not be cut
or damaged. Doing so will impede the
latching mechanism.
13 14
Temporarily tape open the cat flap. Sometimes
it helps for you to be on one side of the door
and your pet on the other. Use food or treats
to coax your pet through the open door. Let
the pet become familiar with passing through.
In time, remove the tape and let the flap hang
in the unlocked position.
15
Using the 4-Way lock.
Place collar
key on center of tunnel and push
flap. Do not force flap open with
magnet in hand. Fit hanging key
to your cat’s collar.

4-Way Locking
Cat Flap
Magnetic
Product Warranty
Please register you product online at www.petsafe.net. All parts are covered under warranty for the life of this product. Labor is covered for the first year of ownership.Thereafter, there is a minimum service charge for
the repair or replacement of the product. Misuse, loss, damage by pet or improper use or handling is not covered. PetSafe®will not pay for loss of time, inconvenience, loss of use of your product or any incidental or
consequential damage.Warranty void if product resold.
Please contact the Customer Care Center at 1-800-732-2677 (US), 1-800457-3911 (Canada) if you need service or for help in troubleshooting and, if needed, to arrange a repair for your product (a service charge may
apply). Also, please visit our website www.petsafe.net for Frequently Asked Questions and Troubleshooting Tips.
Radio Systems Corporation • 10427 Electric Ave. • Knoxville,TN • 865-777-5404 • www.petsafe.net • 400-1023/1
Before installing your cat flap, please read the following step-by-step instructions carefully
Installation Guide for Wood Door (Metal Door Installation on Reverse)
1 2 3 4
Tools Required Measure the belly height of your cat.
This is usually around 4 to 6 inches.
Mark this measurement on the outside
of your door and draw a straight
horizontal line 6
1/2"
.
Using the horizontal line as the starting
point, draw a square 6
1
/
2
" x 6
3
/
4
".
5
Drill holes at each
corner.
6 7 8
Cut along the lines using a jigsaw. Smooth out the rough edges. Place the cat flap in the hole, with the
red 4-way lock facing inside. Mark the
screw holes.
9 10 11 12
Remove the cat flap and drill holes
with a
3/16"
drill bit.
Screw into place. Cut off
excess screw with wire cutters. Cover screw
holes with blanking plugs for neat finish.
Push fit 4-way locking handle into place.
The fixed tunnel is an integral part of
the mechanism and must not be cut
or damaged. Doing so will impede the
latching mechanism.
13
Temporarily tape open the cat flap. Sometimes
it helps for you to be on one side of the door
and your pet on the other. Use food or treats
to coax your pet through the open door. Let
the pet become familiar with passing through.
In time, remove the tape and let the flap hang
in the unlocked position.
14
Using the 4-Way lock.
Place collar
key on center of tunnel and push
flap. Do not force flap open with
magnet in hand. Fit hanging key
to your cat’s collar.