Philips Ced1500bt User manual

CED1500BT

คู่มือผู้ใช้

www.philips.com/support

Always there to help you

使用手冊User manual

Question?

Contact

Philips

English

Contents

1 Safety 2

2 Your car entertainment system 3

Introduction 3

Playable media 3

What's in the box 3

Overview of the main unit 4

Overview of the remote control 5

3 Install the car entertainment system 6

Connect wires 6

Mount into the dashboard 9

4 Get started 10

Prepare the remote control 10

Turn on 10

Use the home menu 10

Set the time 11

Adjust the screen brightness 11

5 Play from hard media 12

Load a disc 12

Connect a USB storage device 12

Control play 13

Browse recorded les 13

6 Listen to radio 14

Switch to radio mode 14

Set up 14

Tune to a radio station 14

Store radio stations in memory 14

Tune to a preset radio station 15

Use RDS related features 15

7 Use Bluetooth devices 16

Pair a device 16

Play audio from a connected device 17

Make a call 17

Adjust Bluetooth settings 18

8 Smart Connect Link 19

9 Universal USB Charging 19

10 Adjust sound 20

Adjust the volume level 20

Mute sound 20

Enable the MAX Sound feature 20

Enable the DBB sound effect 20

Select a preset sound equalizer 20

Others 20

11 Adjust settings 22

Access system setup menus 22

Adjust general settings 22

View system information 22

12 Others 23

Play external audio/video input 23

Use buttons on the steering wheel 23

Reset the system 24

Replace the fuse 24

Upgrade the rmware 24

13 Product information 25

14 Troubleshooting 26

General 26

About the Bluetooth device 26

15 Notice 27

Compliance 27

Care of the environment 27

Trademark notice 28

2EN

1 Safety

Read and understand all instructions before you

use the device. If damage is caused by failure to

follow instructions, the warranty does not apply.

• Use of controls or adjustments or

performance of procedures other than

herein may result in hazardous radiation

exposure or other unsafe operation.

• The device is designed for negative ground

(earth) 12 V DC operation only.

• To reduce the risk of trafc accidents, do

not watch video when driving.

• To ensure safe driving, adjust the volume to

a safe and comfortable level.

• Improper fuses can cause damage or

re. When you need to change the fuse,

consult a professional.

• Use only the supplied mounting hardware

for a safe and secure installation.

• To avoid short circuits, do not expose the

device, remote control or remote control

batteries to rain or water.

• The device shall not be exposed to

dripping or splashing.

• Do not place any sources of danger on

the device (e.g. liquid lled objects, lighted

candles).

• Never insert objects into the ventilation

slots or other openings on the device.

• Never place any objects other than discs

into the disc tray/slot.

• To avoid exposure to laser radiation, do

not disassemble the device.

• Risk of damage to the screen! Never push,

rub, or strike the screen with any object.

• Never use solvents such as benzene,

thinner, cleaners available commercially, or

anti-static sprays intended for discs.

• Clean the device with soft, damp cloth.

Never use substances such as alcohol,

chemicals or household cleaners on the

device.

• Risk of swallowing coin battery!

• The product/remote control may

contain a coin/button type battery,

which can be swallowed. Keep the

battery out of reach of children at all

times! If swallowed, the battery can

cause serious injury or death. Severe

internal burns can occur within two

hours of ingestion.

• If you suspect that a battery has been

swallowed or placed inside any part

of the body, seek immediate medical

attention.

• When you change the batteries, always

keep all new and used batteries out

of reach of children. Ensure that the

battery compartment is completely

secure after you replace the battery.

• If the battery compartment cannot be

completely secured, discontinue use

of the product. Keep out of reach of

children and contact the manufacturer.

English

2 Your car

entertainment

system

Congratulations on your purchase, and

welcome to Philips! To fully benet from the

support that Philips offers, register your product

at www.philips.com/welcome.

Introduction

With the car entertainment system, you can

• listen to music,

• watch videos,

• view pictures,

• listen to FM (RDS included) and AM/MW

radio, and

• make phone calls via Bluetooth.

Playable media

• Disc

• DVD,Video CD, SVCD, Audio CD,

JPEG Picture CD, MP3-CD,WMA-CD

• DVD-R, DVD-RW, DVD+R, DVD+RW,

CD-R, CD-RW

• USB storage device

• Compatibility: USB 2.0, USB 1.1

• Class support: MSC (Mass Storage

Class)

• Maximum capacity: 32 GB

• Files

• File system: FAT16, FAT32

• Maximum number of folders: 99

• Maximum number of tracks/les: 999

• Maximum level of directory: 8

• Video formats: MPEG1, MPEG2

• Picture format: .jpeg

• .mp3 les

Sampling frequencies: 32 kHz, 44.1 kHz,

48 kHz

Bitrates: 8-320 kbps and variable

bitrates

• .wma les

Versions:V4,V7,V8,V9 (L1 and L2)

Sampling frequencies: 44.1 kHz, 48 kHz

Bitrates: 64-192 kbps and variable

bitrates

• ID3 tag V2.0 or later

• Unsupported les:

AAC, WAV, and PCM les

DRM protected WMA les (.wav, .m4a,

.m4p, .mp4, and .aac)

WMA les in lossless format

What's in the box

Check and identify the contents of the package:

1Main unit 2Remote control

3ISO male connector

X 2

4Rubber cushion

5Screw X 4

(M5x8mm)

6Hexagon head

screw

7Remote control

battery

8User manual

abc

def

g h

4EN

Overview of the main unit

• Press to eject the disc.

• Press and hold to adjust the brightness

of LCD screen.

• Press to power on the unit.

• Press and hold to power off the unit.

• Press to mute the speakers or release

them from mute status.

d RESET

• Press to reset the system.

e iR sensor

• The sensor that receives infra-red

signals from the remote control.

f AV-IN

• Connect to the audio and video

output sockets of an external player by

a composite AV cable.

• Connect to a USB storage device.

h LCD screen

CED1500BT

i +/-

• Press to increase or decrease the

volume.

j MIC

• The built-in microphone for phone

calls.

k Disc slot

English

Overview of the remote

control

• Press to eject the disc.

• Press to mute the speakers or release

them from mute status.

• Return to the previous menu or mode.

d VOLUME + / -

• Press to increase or decrease the

volume.

• Access the home menu.

f AUDIO

• Select an audio language or audio

channel.

• Access to system setup menu..

• Select music listening zone.

i DVD AUDIO

• Select an audio language or audio

channel.

ZOOM

SUB

TITLE

ZONE

AUDIO

SU BW

RADIO

OPTION

j SUBW

• Access the menu for subwoofer

settings.

k EQ

• Select a preset sound equalizer.

• Select a music listening zone.

• Select an available subtitle.

• Turn on or off the screen.

o TOP MENU

• Access the top menu.

p DVD MENU

• Access the DVD menu.

• Access the the folder or le list.

r RADIO OPTION

• In radio mode, press to display

available menus or options.

• Start, pause, or resume the play.

t OK

• Conrm an option.

u / /TRACK -/TRACK +

• Skip to the previous or next track,

chapter, or le.

• For DVD, press and hold to select a

speed for fast backward or forward

search.

v BAND

• Select a tuner band.

w / /PRESET +/PRESET -

• Tune to the previous or next preset

radio station.

• Skip to the previous or next folder.

• Turn the car audio on or off.

• Press to adjust the brightness of the

LCD screen.

6EN

3 Install the car

entertainment

system

Always follow the instructions in this chapter in

sequence.

These instructions are for a typical installation.

However, if your car has different requirements,

make the adjustment accordingly. If you have

any question regarding installation kits, consult

your local retailer.

Note

•This system is designed for negative ground (earth) 12V

DC operation only.

•Always install this system in the car dashboard. Other

locations can be dangerous as the rear of the system

heats up during use.

•To avoid short-circuit: before you connect, make sure

that the ignition is off.

•Make sure that you connect the yellow and red power

supply leads after all other leads are connected.

•Make sure that all loose leads are insulated with

electrical tape.

•Make sure that the leads do not get caught under

screws iron parts that will move (e.g. seat rail).

•Make sure that all ground (earth) leads are run to a

common ground (earth) point.

•Use only the supplied mounting hardware for a safe

and secure installation.

•Improper fuses can cause damage or re. When you

need to change the fuse, consult a professional.

•When you connect other devices to this system, make

sure that the rating of the car circuit is higher than the

total fuse value of all the connected devices.

•Never connect speaker wires to the metal body or

chassis of the car.

•Never connect speaker wires with stripes to one another.

Connect wires

Note

•Make sure that all loose leads are insulated with

electrical tape.

•Consult a professional to connect wires as instructed

below.

•Before connection, check the car's wiring carefully.

1 Connect the ISO male connectors.

ISO male

connectors

Connect to

a Green strip,

black-edged

green strip

Rear left speaker

b White strip,

black-edged

white strip

Front left speaker

c Gray strip,

black-edged

gray strip

Front right speaker

d Purple strip,

black-edged

purple strip

Rear right speaker

e Red strip Ignition key +12V DC

when ON/ACC

f Blue strip Motor/electric antenna

relay control lead

g Black strip Ground

h Yellow strip The +12V car battery

which is energized at all

times

2 Connect other wires if necessary.

Caution

•To avoid an accident, the driver must not watch video

while driving. By design, this system disallows watching

video during drive. Park your car in a safe place and

engage the parking brake before watching video.

English

Note

•When the parking brake of your vehicle is not engaged,

the video blocking system is activated. It blocks the

display of front video source only.

•If the system is not properly connected with the

parking brake control module of your vehicle, video

signals will be blocked by the system, with the below

message displayed on the TFT.

Connectors and

sockets on rear

panel

External sockets or

connectors

1 For ISO male

connectors

As indicated above

2REAR OUT R

(Red socket)

Rear right speaker

3AV-IN R

(Red socket)

Right audio channel

output socket of an

external player

4AV-IN L

(White socket)

Left audio channel

output socket of an

external player

5REAR OUT L

(White socket)

Rear left speaker

6VIDEO IN

(Yellow socket)

Video output socket

of an external player

7VIDEO OUT 1

(Yellow socket)

Video input socket

of an external

display device

8VIDEO OUT 2

(Yellow socket)

Video input socket

of an external

display device

9RADIO

ANTENNA

(Black connector)

Radio antenna

10 CAMERA IN

(Purple socket)

Video output socket

of an external

camera

11 SUB-W OUT

(Blue socket)

Sub-woofer

12 REVERSE

CAMERA

(Purple wire)

Reverse camera

(B+)

13 PARKING BRAKE

(Pink wire)

Parking brake (-)

14 External Smart

Link Box (Black

connector)

An external device

compatible with the

application of Smart

Connect Link

15 OE SWC IR

REMOTE IN

(Brown wire)

OE SWC remote in

16 OE SWC IR

REMOTE IN

(Black wire)

Ground

17 OE SWC AD

LEARN

(White wire)

OE SWC AD Learn

line 1

18 OE SWC AD

LEARN

(White wire)

OE SWC AD Learn

line 2

19 OE SWC AD

LEARN

(Black wire)

Ground

20 External Mic

(Black connector)

External microphone

Tip

•The pin arrangement for the ISO connectors depends

on the type of your vehicle.To avoid damage to the

system, connect properly.

8EN

bcde fghijk

English

Mount into the dashboard

Note

•Make sure that wires are correctly connected before

you mount the main unit into a car.

•If preset radio stations are lost when the ignition key

is turned OFF and then back ON, reconnect the red

leads crosswise to the yellow ones.

1 If the car does not have an on-board drive

or navigation computer, disconnect the

negative terminal of the car battery.

• If you disconnect the car battery in

a car that has an on-board drive or

navigation computer, the computer

may lose its memory.

• If the car battery is not disconnected,

to avoid short-circuit, make sure that

bare wires do not touch each other.

2 Make sure that the car dashboard opening

is within these measurements:

• Since the unit cannot be used if the

dashboard opening's slant angle is

above 20 degrees, make sure that the

horizontal slant of the car dashboard

opening is between 0 and 20 degrees.

182 mm

112 mm

5 mm

3 Slide the unit into the dashboard until a

click sound is heard.

4 Reconnect the negative terminal of the car

battery.

10 EN

4 Get started

Caution

•Risk of car accidents! Never watch video or operate

this system while driving.

Prepare the remote control

For the rst time use

Pull the protective sheet out.

» The remote control is ready for use.

Replace the battery

Caution

•Risk of explosion! Keep batteries away from heat,

sunshine or re. Never discard batteries in re.

Note

•Remove the battery if it is exhausted or if the remote

control is not to be used for a long time.

•Batteries contain chemical substances, they should be

disposed of properly.

1 Pull out the battery tray.

2 Insert one CR2025 battery with correct

polarity (+/-) as indicated.

3 Insert the battery tray.

Turn on

Press .

» PHILIPS logo and a progress bar are

displayed while boot-up.

• To turn off the system, press and hold

for 3 seconds.

For the rst time use

After successful boot-up, the following interface

is displayed.

1 Tap [Language] to select a language for

on-screen display.

2 Tap [Radio Region] to select a radio

region that matches your location.

3 Tap [Finish] to complete the initial setup.

» The device switches to radio mode

automatically.

Use the home menu

Note

•If is displayed when you touch an icon, it indicates

that the selected media or feature is unavailable at the

current time.

English

Access the home menu

Tap to access the home menu.

• [Tuner]: Switch the source to FM/

AM radio.

• [Disc]: Switch the source to disc.

• [USB]: Switch the source to USB

storage device.

• [Bluetooth]: Use the Bluetooth

feature.

• [AV1 IN]/[AV2 IN]: Switch the

source to the audio and video input

that is transferred from an external

video player.

• [Mirror]: Connect with the external

mirror box (not supplied).

• [Turn Off LCD]:Turn the LCD off.

• :Access the system menu.

Set the time

1 Tap .

2 Tap .

» The following menu is displayed.

3 Tap [Clock mode] to select a time format.

• [24 Hour]: 24-hour time format

• [12 Hour]: 12-hour time format

4 Tap [Time] , tap the hour or minute digits,

and then tap / to set the hour or minute.

5 Tap to return to the previous menu.

Adjust the screen brightness

Press and hold on the front panel to select a

brightness level of the screen.

12 EN

5 Play from hard

media

You can use this system to listen to audio, watch

videos, and view photos that are stored on a

disc or USB storage device.

Note

•Before use, check for compatible media.

Load a disc

Caution

•Never insert any object other than a disc of 12-cm

diameter into the disc slot.

1 Insert the disc into the disc slot with the

label side facing up.

» Play starts automatically.

• If play does not start automatically, tap

the screen to display the icon, and

then tap to start play.

2 To eject the disc, press .

» When the disc is ejected, the system

switches to the previous source or

radio mode.

Region code

This system can play DVD discs marked with

the following region code.

DVD region code Countries and regions

Asia Pacic, Taiwan, Korea

Connect a USB storage

device

Note

•Make sure that the USB storage device contains

compatible les.

•NTFS (New Technology File System) le system is not

supported.

1 Push the USB socket cover upwards to

open it.

2 Connect the USB storage device to the

USB socket.

3 Tap [USB] on the home menu.

» Play starts automatically.

• To remove the USB storage device,

switch the system to another source

rst.

English

Control play

Videos and pictures

• : Return to the home menu.

•

• For DVD, return to the disc menu or

root menu.

• For recorded les, return to the list of

les or folders.

• / : Skip to the previous or next

title, chapter, track, or le.

• To search forward fast or rewind the

track, tap on the progress bar.

• / : Start, pause, or resume play.

Audios

• : Return to the home menu.

•

• Press once to access the track list.

• Press repeatedly to return to the

playback interface.

• : Return to the list of tracks or folders.

• / : Skip to the previous or next

track.

• To search forward fast or rewind the

track, tap on the progress bar.

• / : Start, pause, or resume play.

• / / : Select a repeat mode.

• : Repeat the current track.

• : For recorded les, repeat all tracks

in the current folder.

• (highlighted): Repeat all tracks.

• : Select random play ( highlighted) or

sequential play ( in gray).

Browse recorded les

During playing recorded les, you can access

the le list and select les from the list.

1 Tap to access the list of les or folders.

2 Tap an icon to select a le category.

• : Display the list of audio tracks or

folders.

• : Display the list of picture les or

folders.

• : Display the list of video les or

folders.

3 Tap the name of a le to start play.

14 EN

6 Listen to radio

Switch to radio mode

After the boot-up at the rst time, the system

switches to radio mode automatically.

To switch the source back to radio afterwards,

tap [Tuner] on the home menu.

» The interface for radio is displayed.

Set up

Before you search for radio stations, make prior

setup.

Tap to display the setup menus.

Select a radio range

1 Tap [Local] to select a tuner sensitivity.

• [Off]: Stations with strong and weak

signals can be tuned to.

• [On]: Only stations with strong signals

can be tuned to.

Enable the RDS feature

Note

•RDS feature is enabled by default.

•Only after the RDS feature is enabled, the option of

[PTY] is displayed.

Tap [RDS On] to enable the RDS feature.

» The option of [PTY] is displayed.

• To disable the RDS feature, tap [RDS

Off].

Tune to a radio station

1 Tap FM or AM to select a band.

• FM bands: FM1, FM2, FM3

• AM bands: AM1,AM2

2 Tap and hold +or -until the frequency of

target radio station is displayed.

• To tune to a radio station automatically,

tap +or -.

Tip

•You can also press BAND on the remote control

repeatedly to select a band.

Store radio stations in memory

You can store up to 6 stations in each band.

Store radio stations manually

1 Select a band.

2 Tune to the target radio station.

English

3 Tap and hold one of the channels (1to 6)

over two seconds.

» The radio station is saved under the

selected channel.

Store radio stations automatically

You can search for a radio station with intro

search, which broadcasts a 10-second preview

of each detected radio station.

1 Select a band.

2 Tap .

3 Tap [Auto Store].

» Auto search starts.The six strongest

stations of the selected band are saved

in preset channels automatically.

Tune to a preset radio station

1 Select a band.

2 Tap one of the preset channels (1to 6) to

select a preset radio station.

Use RDS related features

Note

•Only after RDS feature is enabled, you can use RDS

related features.

Search for RDS programs of a specic

type

1 Tap > [PTY] to display the list of

program types.

2 Tap the name of a program type to start

search.

» Once an RDS station that transmits

programs of the selected type is

found, the RDS station is broadcast

automatically.

• To save the RDS station, tap and hold

one of the preset channels.

• To search for another RDS station,

repeat steps 1 and 2.

RDS program types

Item Program

type

Description

1 NEWS News services

2 AFFAIRS Politics and current

affairs

3 INFO Special information

programs

4 SPORT Sports

5 EDUCATE Education and advanced

training

6 DRAMA Radio plays and

literature

7 CULTURE Culture, religion and

society

8 SCIENCE Science

9 VARIED Entertainment programs

10 POP M Pop music

11 ROCK M Rock music

12 MOR M Light music

13 LIGHT M Light classical music

14 CLASSICS Classical music

15 OTHER M Special music programs

16 WEATHER Weather

17 FINANCE Finance

18 CHILDREN Children’s programs

19 SOCIAL Social Affairs

20 RELIGION Religion

16 EN

21 PHONE IN Phone In

22 TRAVEL Tr av el

23 LEISURE Leisure

24 JAZZ Jazz Music

25 COUNTRY Country Music

26 NATION M National Music

27 OLDIES Oldies Music

28 FOLK M Folk Music

29 DOCUMENT Documentary

30 TEST Alarm Test

31 ALARM Alarm

Use alternate frequencies

If the signal of an RDS station is poor, enable

the AF (Alternate Frequency) function.The

system searches for a strong station that

broadcasts the same program.

Tap AF to enable or disable the AF function.

• AF (highlighted):The function is enabled.

• AF (in gray):The function is disabled.

7 Use Bluetooth

devices

With this system, you can listen to audio from a

player and make a call through Bluetooth.

Pair a device

Note

•WOOX Innovations does not guarantee the

compatibility with all Bluetooth devices.

•Before pairing a device with this system, read its user

manual for Bluetooth compatibility.

•Make sure that Bluetooth function is enabled on your

device, and your device is set as visible to all other

Bluetooth devices.

•The operational range between this system and a

Bluetooth device is approximately 8 meters (24 feet).

•Any obstacle between this system and a Bluetooth

device can reduce the operational range.

•Keep away from any other electronic device that may

cause interference.

On your device, follow the steps below.

1 Search for Bluetooth devices.

2 In the device list, select CE1500BT.

3 Enter the default password "0000", and

then conrm the password entry.

4 Enable or permit the connection with

CE1500BT.

» If the connection succeeds,

[CONNECTED OK] is displayed on

the LCD screen of this system.

• To disconnect a device, disable the

Bluetooth function on the device.

Before connecting another device,

disconnect the current device rst.

English

Play audio from a connected

device

If the connected Bluetooth device supports

Advanced Audio Distribution Prole (A2DP),

you can listen to tracks that are stored on the

device through the system. If the device also

supports Audio Video Remote Control Prole

(AVRCP) prole, you can control play on the

system or with its remote control.

1 Play a track on the connected device.

2 On this system, tap to display the music

playback interface.

3 Tap icons on the interface to control play.

• : Pause or resume play.

• / : Select the previous or

next track.

Note

•If the connected device does not support the AVRCP

prole, control play on the connected device.

Make a call

Note

•Keep the Bluetooth connection active between the

system and your mobile phone.

Locate the external microphone

You can connect an external microphone for

better communication quality.

Note

•The external microphone is not included in the

packaging of this system.

1 Make sure that the microphone is

connected to this system.

2 Place the microphone at a proper location,

such as, stick it onto the dashboard, or clip

it on the sun-shield.

Call a number

You can make phone calls with the system.

1 Tap .

» The keypad is displayed.

2 Tap number icons to enter the phone

number.

• To clear the last digit, tap .

• To clear all digits, tap .

• To return to the previous screen, tap

18 EN

3 Tap to send the call.

• To end the call, tap .

• To enter numbers during the call, tap

to display the keypad rst.

Redial the last called number

1 Tap .

» The last called number is displayed.

2 Tap again to send the call.

Answer a call

Note

•By default, all incoming calls are picked up automatically.

You can disable the function of automatic answer.

1 When there is an incoming call, [Incoming

call…] is displayed on the screen.

2 Tap to answer the call.

• To reject or end the call, tap .

Transfer a phone call to mobile phone

By default, the voice comes from the

loudspeakers during a call.

1 Tap to transfer the phone call to your

mobile phone.

» The loudspeakers are muted, and the

voice comes from the mobile phone

only.

2 Take up your mobile phone for the

conversation.

Adjust Bluetooth settings

Tap to access the menus for Bluetooth

settings.

Bluetooth

settings

Options Description

[Auto Answer] [On] Answer phone calls

automatically when

the paired mobile

phone receives an

incoming call.

[Off] Answer phone calls

manually.

[Pin Code] Set the password

for pairing the car

entertainment

system with

another Bluetooth

device.The default

password is 0000.

[Device name] CED

1500BT

Turn on the external

microphone.

[Phone Name] Show the phone

name that is

connected with

CED1500BT.

Other manuals for CED1500BT

Table of contents

Languages:

Philips CED1500BT User manual

Popular Car Video System manuals by other brands