Philips CED1500BT User manual

CED1500BT
Register your product and get support at
www.philips.com/support
Always there to help you
User manual
Question?
Contact
Philips

1
English
EN
Contents
1 Safety 2
2 Your car entertainment system 3
Introduction 3
Playable media 3
What's in the box 3
Overview of the main unit 4
Overview of the remote control 5
3 Install the car entertainment system 6
Connect wires 6
Mount into the dashboard 9
4 Get started 10
Prepare the remote control 10
Turn on 10
Use the home menu 10
Set the time 11
Adjust the screen brightness 11
5 Play from hard media 12
Load a disc 12
Connect a USB storage device 12
Control play 13
%URZVHUHFRUGHGÀOHV 
6 Listen to radio 14
Switch to radio mode 14
Set up 14
Tune to a radio station 14
Store radio stations in memory 14
Tune to a preset radio station 15
Use RDS related features 15
7 Use Bluetooth devices 16
Pair a device 16
Play audio from a connected device 17
Make a call 17
Adjust Bluetooth settings 18
8 Smart Connect Link 19
9 Universal USB Charging 19
10 Adjust sound 20
Adjust the volume level 20
Mute sound 20
Enable the MAX Sound feature 20
Enable the DBB sound effect 20
Select a preset sound equalizer 20
Others 20
11 Adjust settings 22
Access system setup menus 22
Adjust general settings 22
View system information 22
12 Others 23
Play external audio/video input 23
Use buttons on the steering wheel 23
Reset the system 24
Replace the fuse 24
8SJUDGHWKHÀUPZDUH 
13 Product information 25
14 Troubleshooting 26
General 26
About the Bluetooth device 26
15 Notice 27
Compliance 27
Care of the environment 27
Trademark notice 28
Copyright 28

2EN
1 Safety
Read and understand all instructions before you
use the device. If damage is caused by failure to
follow instructions, the warranty does not apply.
 Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
 The device is designed for negative ground
(earth) 12 V DC operation only.
 7RUHGXFHWKHULVNRIWUDIÀFDFFLGHQWVGR
not watch video when driving.
 To ensure safe driving, adjust the volume to
a safe and comfortable level.
 Improper fuses can cause damage or
ÀUH:KHQ\RXQHHGWRFKDQJHWKHIXVH
consult a professional.
 Use only the supplied mounting hardware
for a safe and secure installation.
 To avoid short circuits, do not expose the
device, remote control or remote control
batteries to rain or water.
 The device shall not be exposed to
dripping or splashing.
 Do not place any sources of danger on
WKHGHYLFHHJOLTXLGÀOOHGREMHFWVOLJKWHG
candles).
 Never insert objects into the ventilation
slots or other openings on the device.
 Never place any objects other than discs
into the disc tray/slot.
 To avoid exposure to laser radiation, do
not disassemble the device.
 Risk of damage to the screen! Never push,
rub, or strike the screen with any object.
 Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
 Clean the device with soft, damp cloth.
Never use substances such as alcohol,
chemicals or household cleaners on the
device.
 Risk of swallowing coin battery!
 The product/remote control may
contain a coin/button type battery,
which can be swallowed. Keep the
battery out of reach of children at all
times! If swallowed, the battery can
cause serious injury or death. Severe
internal burns can occur within two
hours of ingestion.
 If you suspect that a battery has been
swallowed or placed inside any part
of the body, seek immediate medical
attention.
 When you change the batteries, always
keep all new and used batteries out
of reach of children. Ensure that the
battery compartment is completely
secure after you replace the battery.
 If the battery compartment cannot be
completely secured, discontinue use
of the product. Keep out of reach of
children and contact the manufacturer.

3
English
EN
2 Your car
entertainment
system
Congratulations on your purchase, and
ZHOFRPHWR3KLOLSV7RIXOO\EHQHÀWIURPWKH
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the car entertainment system, you can
 listen to music,
 watch videos,
 view pictures,
 listen to FM (RDS included) and AM/MW
radio, and
 make phone calls via Bluetooth.
Playable media
 Disc
 DVD,Video CD, SVCD, Audio CD,
JPEG Picture CD, MP3-CD,WMA-CD
 DVD-R, DVD-RW, DVD+R, DVD+RW,
CD-R, CD-RW
 USB storage device
 Compatibility: USB 2.0, USB 1.1
 Class support: MSC (Mass Storage
Class)
 Maximum capacity: 32 GB
 Files
 File system: FAT16, FAT32
 Maximum number of folders: 99
 0D[LPXPQXPEHURIWUDFNVÀOHV
 Maximum level of directory: 8
 Video formats: MPEG1, MPEG2
 Picture format: .jpeg
 PSÀOHV
Sampling frequencies: 32 kHz, 44.1 kHz,
48 kHz
Bitrates: 8-320 kbps and variable
bitrates
 ZPDÀOHV
Versions:V4,V7,V8,V9 (L1 and L2)
Sampling frequencies: 44.1 kHz, 48 kHz
Bitrates: 64-192 kbps and variable
bitrates
 ID3 tag V2.0 or later
 8QVXSSRUWHGÀOHV
$$&:$9DQG3&0ÀOHV
'50SURWHFWHG:0$ÀOHVZDYPD
.m4p, .mp4, and .aac)
:0$ÀOHVLQORVVOHVVIRUPDW
What's in the box
Check and identify the contents of the package:
1Main unit 2Remote control
3ISO male connector
X 2
4Rubber cushion
5Screw X 4
(M5x8mm)
6Hexagon head
screw
7Remote control
battery
8User manual
abc
def
gh

4EN
Overview of the main unit
a
 Press to eject the disc.
b
 Press and hold to adjust the brightness
of LCD screen.
c
 Press to power on the unit.
 Press and hold to power off the unit.
 Press to mute the speakers or release
them from mute status.
d RESET
 Press to reset the system.
e iR sensor
 The sensor that receives infra-red
signals from the remote control.
f AV-IN
 Connect to the audio and video
output sockets of an external player by
a composite AV cable.
g
 Connect to a USB storage device.
h LCD screen
CED1500BT
a
b
c
e
f
h
i
g
k
j
d
i +/-
 Press to increase or decrease the
volume.
j MIC
 The built-in microphone for phone
calls.
k Disc slot

5
English
EN
Overview of the remote
control
a
 Press to eject the disc.
b
 Press to mute the speakers or release
them from mute status.
c
 Return to the previous menu or mode.
d VOLUME + / -
 Press to increase or decrease the
volume.
e
 Access the home menu.
f AUDIO
 Select an audio language or audio
channel.
g
 Access to system setup menu..
h
 Select music listening zone.
i DVD AUDIO
 Select an audio language or audio
channel.
b
c
a
d
f
h
g
e
j
i
k
l
x
w
y
v
t
u
s
q
o
p
r
n
m
ZOOM
SUB
TITLE
ZONE
AUDIO
SU BW
RADIO
OPTION
j SUBW
 Access the menu for subwoofer
settings.
k EQ
 Select a preset sound equalizer.
l
 Select a music listening zone.
m
 Select an available subtitle.
n
 Turn on or off the screen.
o TOP MENU
 Access the top menu.
p DVD MENU
 Access the DVD menu.
q
 $FFHVVWKHWKHIROGHURUÀOHOLVW
r RADIO OPTION
 In radio mode, press to display
available menus or options.
s
 Start, pause, or resume the play.
t OK
 &RQÀUPDQRSWLRQ
u / /TRACK -/TRACK +
 Skip to the previous or next track,
FKDSWHURUÀOH
 For DVD, press and hold to select a
speed for fast backward or forward
search.
v BAND
 Select a tuner band.
w / /PRESET +/PRESET -
 Tune to the previous or next preset
radio station.
 Skip to the previous or next folder.
x
 Turn the car audio on or off.
y
 Press to adjust the brightness of the
LCD screen.

6EN
3 Install the car
entertainment
system
Always follow the instructions in this chapter in
sequence.
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Note
This system is designed for negative ground (earth) 12V
DC operation only.
Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
To avoid short-circuit: before you connect, make sure
that the ignition is off.
Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
Make sure that all loose leads are insulated with
electrical tape.
Make sure that the leads do not get caught under
screws iron parts that will move (e.g. seat rail).
Make sure that all ground (earth) leads are run to a
common ground (earth) point.
Use only the supplied mounting hardware for a safe
and secure installation.
,PSURSHUIXVHVFDQFDXVHGDPDJHRUÀUH:KHQ\RX
need to change the fuse, consult a professional.
When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
Never connect speaker wires to the metal body or
chassis of the car.
Never connect speaker wires with stripes to one another.
Connect wires
Note
Make sure that all loose leads are insulated with
electrical tape.
Consult a professional to connect wires as instructed
below.
Before connection, check the car's wiring carefully.
1 Connect the ISO male connectors.
ISO male
connectors
Connect to
a Green strip,
black-edged
green strip
Rear left speaker
b White strip,
black-edged
white strip
Front left speaker
c Gray strip,
black-edged
gray strip
Front right speaker
d Purple strip,
black-edged
purple strip
Rear right speaker
e Red strip Ignition key +12V DC
when ON/ACC
f Blue strip Motor/electric antenna
relay control lead
g Black strip Ground
h Yellow strip The +12V car battery
which is energized at all
times
2 Connect other wires if necessary.
Caution
To avoid an accident, the driver must not watch video
while driving. By design, this system disallows watching
video during drive. Park your car in a safe place and
engage the parking brake before watching video.

7
English
EN
Note
When the parking brake of your vehicle is not engaged,
the video blocking system is activated. It blocks the
display of front video source only.
If the system is not properly connected with the
parking brake control module of your vehicle, video
signals will be blocked by the system, with the below
message displayed on the TFT.
Connectors and
sockets on rear
panel
External sockets or
connectors
1 For ISO male
connectors
As indicated above
2REAR OUT R
(Red socket)
Rear right speaker
3AV-IN R
(Red socket)
Right audio channel
output socket of an
external player
4AV-IN L
(White socket)
Left audio channel
output socket of an
external player
5REAR OUT L
(White socket)
Rear left speaker
6VIDEO IN
(Yellow socket)
Video output socket
of an external player
7VIDEO OUT 1
(Yellow socket)
Video input socket
of an external
display device
8VIDEO OUT 2
(Yellow socket)
Video input socket
of an external
display device
9RADIO
ANTENNA
(Black connector)
Radio antenna
10 CAMERA IN
(Purple socket)
Video output socket
of an external
camera
11 SUB-W OUT
(Blue socket)
Sub-woofer
12 REVERSE
CAMERA
(Purple wire)
Reverse camera
(B+)
13 PARKING BRAKE
(Pink wire)
Parking brake (-)
14 External Smart
Link Box (Black
connector)
An external device
compatible with the
application of Smart
Connect Link
15 OE SWC IR
REMOTE IN
(Brown wire)
OE SWC remote in
16 OE SWC IR
REMOTE IN
(Black wire)
Ground
17 OE SWC AD
LEARN
(White wire)
OE SWC AD Learn
line 1
18 OE SWC AD
LEARN
(White wire)
OE SWC AD Learn
line 2
19 OE SWC AD
LEARN
(Black wire)
Ground
20 External Mic
(Black connector)
External microphone
Tip
The pin arrangement for the ISO connectors depends
on the type of your vehicle.To avoid damage to the
system, connect properly.

8EN
a
bcdefg hijk
l
m
n
t
o
p
q
r
s

9
English
EN
Mount into the dashboard
Note
Make sure that wires are correctly connected before
you mount the main unit into a car.
If preset radio stations are lost when the ignition key
is turned OFF and then back ON, reconnect the red
leads crosswise to the yellow ones.
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
 If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
 If the car battery is not disconnected,
to avoid short-circuit, make sure that
bare wires do not touch each other.
2 Make sure that the car dashboard opening
is within these measurements:
 Since the unit cannot be used if the
dashboard opening's slant angle is
above 20 degrees, make sure that the
horizontal slant of the car dashboard
opening is between 0 and 20 degrees.
182 mm
112 mm
5 mm
3 Slide the unit into the dashboard until a
click sound is heard.
4 Reconnect the negative terminal of the car
battery.

10 EN
4 Get started
Caution
Risk of car accidents! Never watch video or operate
this system while driving.
Prepare the remote control
)RUWKHÀUVWWLPHXVH
Pull the protective sheet out.
» The remote control is ready for use.
Replace the battery
Caution
Risk of explosion! Keep batteries away from heat,
VXQVKLQHRUÀUH1HYHUGLVFDUGEDWWHULHVLQÀUH
Note
Remove the battery if it is exhausted or if the remote
control is not to be used for a long time.
Batteries contain chemical substances, they should be
disposed of properly.
1 Pull out the battery tray.
2 Insert one CR2025 battery with correct
polarity (+/-) as indicated.
3 Insert the battery tray.
Turn on
Press .
» PHILIPS logo and a progress bar are
displayed while boot-up.
 To turn off the system, press and hold
for 3 seconds.
)RUWKHÀUVWWLPHXVH
After successful boot-up, the following interface
is displayed.
1 Tap [Language] to select a language for
on-screen display.
2 Tap [Radio Region] to select a radio
region that matches your location.
3 Tap [Finish] to complete the initial setup.
» The device switches to radio mode
automatically.
Use the home menu
Note
If is displayed when you touch an icon, it indicates
that the selected media or feature is unavailable at the
current time.

11
English
EN
Access the home menu
Tap to access the home menu.
 [Tuner]: Switch the source to FM/
AM radio.
 [Disc]: Switch the source to disc.
 [USB]: Switch the source to USB
storage device.
 [Bluetooth]: Use the Bluetooth
feature.
 [AV1 IN]/[AV2 IN]: Switch the
source to the audio and video input
that is transferred from an external
video player.
 [Mirror]: Connect with the external
mirror box (not supplied).
 [Turn Off LCD]:Turn the LCD off.
 :Access the system menu.
Set the time
1 Tap .
2 Tap .
» The following menu is displayed.
3 Tap [Clock mode] to select a time format.
 [24 Hour]: 24-hour time format
 [12 Hour]: 12-hour time format
4 Tap [Time] , tap the hour or minute digits,
and then tap / to set the hour or minute.
5 Tap to return to the previous menu.
Adjust the screen brightness
Press and hold on the front panel to select a
brightness level of the screen.

12 EN
5 Play from hard
media
You can use this system to listen to audio, watch
videos, and view photos that are stored on a
disc or USB storage device.
Note
Before use, check for compatible media.
Load a disc
Caution
Never insert any object other than a disc of 12-cm
diameter into the disc slot.
1 Insert the disc into the disc slot with the
label side facing up.
» Play starts automatically.
 If play does not start automatically, tap
the screen to display the icon, and
then tap to start play.
2 To eject the disc, press .
» When the disc is ejected, the system
switches to the previous source or
radio mode.
Region code
This system can play DVD discs marked with
the following region code.
DVD region code Countries and regions
$VLD3DFLÀF7DLZDQ.RUHD
Connect a USB storage
device
Note
Make sure that the USB storage device contains
FRPSDWLEOHÀOHV
17)61HZ7HFKQRORJ\)LOH6\VWHPÀOHV\VWHPLVQRW
supported.
1 Push the USB socket cover upwards to
open it.
2 Connect the USB storage device to the
USB socket.
3 Tap [USB] on the home menu.
» Play starts automatically.
 To remove the USB storage device,
switch the system to another source
ÀUVW

13
English
EN
Control play
Videos and pictures
 : Return to the home menu.

 For DVD, return to the disc menu or
root menu.
 )RUUHFRUGHGÀOHVUHWXUQWRWKHOLVWRI
ÀOHVRUIROGHUV
 / : Skip to the previous or next
WLWOHFKDSWHUWUDFNRUÀOH
 To search forward fast or rewind the
track, tap on the progress bar.
 / : Start, pause, or resume play.
Audios
 : Return to the home menu.

 Press once to access the track list.
 Press repeatedly to return to the
playback interface.
 : Return to the list of tracks or folders.
 / : Skip to the previous or next
track.
 To search forward fast or rewind the
track, tap on the progress bar.
 / : Start, pause, or resume play.
 / / : Select a repeat mode.
 : Repeat the current track.
 )RUUHFRUGHGÀOHVUHSHDWDOOWUDFNV
in the current folder.
 (highlighted): Repeat all tracks.
 : Select random play ( highlighted) or
sequential play ( in gray).
%URZVHUHFRUGHGÀOHV
'XULQJSOD\LQJUHFRUGHGÀOHV\RXFDQDFFHVV
WKHÀOHOLVWDQGVHOHFWÀOHVIURPWKHOLVW
1 Tap WRDFFHVVWKHOLVWRIÀOHVRUIROGHUV
2 7DSDQLFRQWRVHOHFWDÀOHFDWHJRU\
 : Display the list of audio tracks or
folders.
 'LVSOD\WKHOLVWRISLFWXUHÀOHVRU
folders.
 'LVSOD\WKHOLVWRIYLGHRÀOHVRU
folders.
3 7DSWKHQDPHRIDÀOHWRVWDUWSOD\

14 EN
6 Listen to radio
Switch to radio mode
$IWHUWKHERRWXSDWWKHÀUVWWLPHWKHV\VWHP
switches to radio mode automatically.
To switch the source back to radio afterwards,
tap [Tuner] on the home menu.
» The interface for radio is displayed.
Set up
Before you search for radio stations, make prior
setup.
Tap to display the setup menus.
Select a radio range
1 Tap [Local] to select a tuner sensitivity.
 [Off]: Stations with strong and weak
signals can be tuned to.
 [On]: Only stations with strong signals
can be tuned to.
Enable the RDS feature
Note
RDS feature is enabled by default.
Only after the RDS feature is enabled, the option of
[PTY] is displayed.
Tap [RDS On] to enable the RDS feature.
» The option of [PTY] is displayed.
 To disable the RDS feature, tap [RDS
Off].
Tune to a radio station
1 Tap FM or AM to select a band.
 FM bands: FM1, FM2, FM3
 AM bands: AM1,AM2
2 Tap and hold +or -until the frequency of
target radio station is displayed.
 To tune to a radio station automatically,
tap +or -.
Tip
You can also press BAND on the remote control
repeatedly to select a band.
Store radio stations in memory
You can store up to 6 stations in each band.
Store radio stations manually
1 Select a band.
2 Tune to the target radio station.

15
English
EN
3 Tap and hold one of the channels (1to 6)
over two seconds.
» The radio station is saved under the
selected channel.
Store radio stations automatically
You can search for a radio station with intro
search, which broadcasts a 10-second preview
of each detected radio station.
1 Select a band.
2 Tap .
3 Tap [Auto Store].
» Auto search starts.The six strongest
stations of the selected band are saved
in preset channels automatically.
Tune to a preset radio station
1 Select a band.
2 Tap one of the preset channels (1to 6) to
select a preset radio station.
Use RDS related features
Note
Only after RDS feature is enabled, you can use RDS
related features.
6HDUFKIRU5'6SURJUDPVRIDVSHFLÀF
type
1 Tap > [PTY] to display the list of
program types.
2 Tap the name of a program type to start
search.
» Once an RDS station that transmits
programs of the selected type is
found, the RDS station is broadcast
automatically.
 To save the RDS station, tap and hold
one of the preset channels.
 To search for another RDS station,
repeat steps 1 and 2.
RDS program types
Item Program
type
Description
1 NEWS News services
2 AFFAIRS Politics and current
affairs
3 INFO Special information
programs
4 SPORT Sports
5 EDUCATE Education and advanced
training
6 DRAMA Radio plays and
literature
7 CULTURE Culture, religion and
society
8 SCIENCE Science
9 VARIED Entertainment programs
10 POP M Pop music
11 ROCK M Rock music
12 MOR M Light music
13 LIGHT M Light classical music
14 CLASSICS Classical music
15 OTHER M Special music programs
16 WEATHER Weather
17 FINANCE Finance
18 CHILDREN Children’s programs
19 SOCIAL Social Affairs
20 RELIGION Religion

16 EN
21 PHONE IN Phone In
22 TRAVEL Tr av el
23 LEISURE Leisure
24 JAZZ Jazz Music
25 COUNTRY Country Music
26 NATION M National Music
27 OLDIES Oldies Music
28 FOLK M Folk Music
29 DOCUMENT Documentary
30 TEST Alarm Test
31 ALARM Alarm
Use alternate frequencies
If the signal of an RDS station is poor, enable
the AF (Alternate Frequency) function.The
system searches for a strong station that
broadcasts the same program.
Tap AF to enable or disable the AF function.
 AF (highlighted):The function is enabled.
 AF (in gray):The function is disabled.
7 Use Bluetooth
devices
With this system, you can listen to audio from a
player and make a call through Bluetooth.
Pair a device
Note
WOOX Innovations does not guarantee the
compatibility with all Bluetooth devices.
Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
The operational range between this system and a
Bluetooth device is approximately 8 meters (24 feet).
Any obstacle between this system and a Bluetooth
device can reduce the operational range.
Keep away from any other electronic device that may
cause interference.
On your device, follow the steps below.
1 Search for Bluetooth devices.
2 In the device list, select CE1500BT.
3 Enter the default password "0000", and
WKHQFRQÀUPWKHSDVVZRUGHQWU\
4 Enable or permit the connection with
CE1500BT.
» If the connection succeeds,
[CONNECTED OK] is displayed on
the LCD screen of this system.
 To disconnect a device, disable the
Bluetooth function on the device.
Before connecting another device,
GLVFRQQHFWWKHFXUUHQWGHYLFHÀUVW

17
English
EN
Play audio from a connected
device
If the connected Bluetooth device supports
$GYDQFHG$XGLR'LVWULEXWLRQ3URÀOH$'3
you can listen to tracks that are stored on the
device through the system. If the device also
VXSSRUWV$XGLR9LGHR5HPRWH&RQWURO3URÀOH
$95&3SURÀOH\RXFDQFRQWUROSOD\RQWKH
system or with its remote control.
1 Play a track on the connected device.
2 On this system, tap to display the music
playback interface.
3 Tap icons on the interface to control play.
 : Pause or resume play.
 / : Select the previous or
next track.
Note
If the connected device does not support the AVRCP
SURÀOHFRQWUROSOD\RQWKHFRQQHFWHGGHYLFH
Make a call
Note
Keep the Bluetooth connection active between the
system and your mobile phone.
Locate the external microphone
You can connect an external microphone for
better communication quality.
Note
The external microphone is not included in the
packaging of this system.
1 Make sure that the microphone is
connected to this system.
2 Place the microphone at a proper location,
such as, stick it onto the dashboard, or clip
it on the sun-shield.
Call a number
You can make phone calls with the system.
1 Tap .
» The keypad is displayed.
2 Tap number icons to enter the phone
number.
 To clear the last digit, tap .
 To clear all digits, tap .
 To return to the previous screen, tap
.

18 EN
3 Tap to send the call.
 To end the call, tap .
 To enter numbers during the call, tap
WRGLVSOD\WKHNH\SDGÀUVW
Redial the last called number
1 Tap .
» The last called number is displayed.
2 Tap again to send the call.
Answer a call
Note
By default, all incoming calls are picked up automatically.
You can disable the function of automatic answer.
1 When there is an incoming call, [Incoming
call…] is displayed on the screen.
2 Tap to answer the call.
 To reject or end the call, tap .
Transfer a phone call to mobile phone
By default, the voice comes from the
loudspeakers during a call.
1 Tap to transfer the phone call to your
mobile phone.
» The loudspeakers are muted, and the
voice comes from the mobile phone
only.
2 Take up your mobile phone for the
conversation.
Adjust Bluetooth settings
Tap to access the menus for Bluetooth
settings.
Bluetooth
settings
Options Description
[Auto Answer] [On] Answer phone calls
automatically when
the paired mobile
phone receives an
incoming call.
[Off] Answer phone calls
manually.
[Pin Code] Set the password
for pairing the car
entertainment
system with
another Bluetooth
device.The default
password is 0000.
[Device name] CED
1500BT
Turn on the external
microphone.
[Phone Name] Show the phone
name that is
connected with
CED1500BT.