Philips sonicare 3000 Series User manual

3000 Series
4000 Series

1
2
3
4
6
5
7 8

empty page before TOC

English 6
Русский 19
Қазақша 37

English
6English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome.
Important safety information
Only use the product for its intended purpose. Read
this important information carefully before you use
the product and its batteries and accessories, and
save it for future reference. Misuse can lead to
hazards or serious injuries.
Intended use
3000 Series power toothbrushes are intended to
remove adherent plaque and food debris from the
teeth to reduce tooth decay and improve and
maintain oral health. 3000 Series power toothbrushes
are intended for consumer home use. Use by children
should be with adult supervision.
Your Philips Sonicare toothbrush
1 Hygienic travel cap
2 Brush head
3 Handle
4 Power on/off button
5 Brush head replacement reminder
6 Battery level indicator
7 USB charger (wall adapter not included)
8 Travel case (Specific models only)
Note: Wall adapter not included. Only use 5V IPX4
adapter (Type A).
Note: Brush heads may vary.

7
English
Getting started
Attaching the brush head
1Align the brush head so the bristles point in the
same direction as the front of the handle.
2Firmly press the brush head down onto the metal
shaft until it stops.
Note: It is normal to see a slight gap between the
brush head and the handle. This allows the brush
head to vibrate properly.
Charging your Philips Sonicare
1Plug the USB charging cord into a wall adapter that
is connected to a electrical outlet.
2Place the handle on the charger.
- The light of the battery level indicator
illuminates and the handle beeps twice. This
indicates that the toothbrush is charging.
Note: It can take up to 24 hours to fully charge the
battery, but you can use the Philips Sonicare
toothbrush before it is fully charged.
Using your Philips Sonicare toothbrush
If you are using your Sonicare toothbrush for the first
time, it is normal to feel more vibration than when
using a non-electric toothbrush. It is common for first
time users to apply too much pressure. Only apply
gentle pressure and let the toothbrush do the
brushing for you. Please follow brushing instructions
below for the best experience. To help you transition
to your new Sonicare power toothbrush, it comes with
the EasyStart feature turned on. This feature gently
increases the power over the first 14 brushings to help

8English
you adapt to brushing with a Philips Sonicare
toothbrush.
Brushing instructions
1Wet the bristles and apply a small amount of
toothpaste.
2Place the toothbrush bristles against the teeth at a
slight angle (45 degrees), pressing gently to make
the bristles reach the gumline or slightly beneath
the gumline.
Note: Keep the center of the brush in contact with
the teeth at all times.
3Press the power on/off button to turn on the
Philips Sonicare.
4Gently keep the bristles placed on the teeth and in
the gumline. Brush your teeth with small back and
forth motion so the bristles reach between the
teeth. Continue this motion throughout your
brushing cycle.
Note: The bristles should slightly flare. It is not
recommended to scrub as you would with a
manual toothbrush.
5To clean the inside surfaces of the front teeth, tilt
the brush handle semi-upright and make several
vertical overlapping brushing strokes on each
tooth.
Note: To make sure you brush evenly throughout
the mouth, divide your mouth into 4 sections using
the Quadpacer feature (see chapter ‘Features’).
2
4
3
1
6Begin brushing in section 1 (outside upper teeth)
and brush for 30 seconds before you move to
section 2 (inside upper teeth). Continue brushing in
section 3 (outside lower teeth) and brush for 30
seconds before you move to section 4 (inside
lower teeth).

9
English
7After you have completed the brushing cycle, you
can spend additional time brushing the chewing
surfaces of your teeth and areas where staining
occurs. You can also brush your tongue, with the
toothbrush turned on or off, as you prefer.
Your Philips Sonicare toothbrush should be safe to
use on braced (brush heads wear out sooner when
used on braces) and dental restorations (fillings,
crowns, veneers) if they are properly adhered and
not compromised. If a problem occurs, please
follow up with a dental professional.
Note: When the Philips Sonicare toothbrush is used in
clinical studies, the handle should be fully charged
and the EasyStart feature deactivated.
Charging and battery status
1Attach the USB charging cord to a wall adapter,
plug the wall adapter into an electrical wall outlet.
2Place the handle on the charger.
Note: The handle will emit 2 short beeps to confirm
that the handle is placed properly on the charger and
is charging.
Note: This Philips Sonicare toothbrush is designed to
provide at least 28 brushing sessions, each session
lasting 2 minutes (14 days if used twice per day). The
battery level indicator shows the battery status when
you complete the 2-minute brushing session, when
you pause the handle, or while it is charging.
Battery status (when handle is on a working charger)
Battery status Battery indicator
Full Solid green (turns off after 30
seconds)
Charging Flashing green

10 English
Battery status (When handle is not placed on charger)
Battery status Battery indicator Sound
Full Solid green -
Partially full Flashing green -
Low Flashing orange 3 beeps
Empty Flashing orange 2 sets of 5 beeps
Note: To save energy, the battery light will turn off
when not in use.
Note: When the battery is completely empty, the
Philips Sonicare toothbrush turns off. Place the Philips
Sonicare toothbrush on the charger to charge it.
Note: To keep the battery fully charged at all times,
you may keep your Philips Sonicare toothbrush on the
charger when not in use.
Features
- Intensities
- EasyStart
- Brush head replacement reminder
- Pressure sensor
- Quadpacer
- SmarTimer
Intensities
Your power toothbrush gives you the option to
choose between low and high intensity.
Note: When you use the toothbrush for the first time,
the default setting is the low intensity.
- Press the power button once to turn on the
toothbrush.
- Press a second time within 2 seconds to change
the intensity.
- Press a third time within 2 seconds to pause.
After 2 seconds of brushing, pressing the power
button again will also pause the toothbrush.