Philips Essence HR7755 Manual

Essence HR7755
Recipes & Directions for use
Przepisy i instrukcja obsługi
Reţete şi Instrucţiuni de utilizare
Рецепты и Инструкции по эксплуатации
Recepty & Návod k použití
Recepti in navodila za uporabo
Рецепти та інструкції з використання приладу
Pечепти и инструкчии за употреба
Recepti i uputstvo za upotrebu

2

B
D
C
H
G
L
N
O
P
Q
M
A
S
V
T
b
a
Y
Z
W
X
R
c
U
E
F
K
I
J
3

4

ENGLISH 6
POL KI 25
ROMÂNĂ 44
РУССКИЙ 62
ČE KY 85
MAGYAR 103
LOVEN KY 122
УКР ЇНСЬКІЙ 141
БЪЛГ РСКИ 161
RP KI 182
HR7755
5

ENGLISH6
Introduction
This appliance is equipped with an automatic
thermal cut-out system.This system will
automatically cut off the power supply to the
appliance in case of overheating.
General description
AMotor unit
BSpeed control
- P= pulse
- 0 = off
- 1 = lowest speed
- 2 = highest speed
CScrew cap (must be placed to be able to use
food-processing functions)
DFood processing bowl
ETool holder
FLid of food processing bowl
GBlender jar
HBlender jar lid
IFeed tube
JPusher
KStopper
LKneading accessory
MMetal blade + protective cover
NSlicing insert medium
OShredding insert medium
PInsert holder
QEmulsifying disc
RGear housing meat mincer
SCutter housing meat mincer
TWorm shaft
UScrew ring
VCutter unit
WMedium grinding disc, 4 mm dia.
XCoarse grinding disc, 8 mm dia.
YSeparator
ZSausage horn
aTr ay
bPusher
cRelease lever
Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗Check if the voltage indicated on the
appliance corresponds to the local mains
voltage before you connect the appliance.
◗Never use any accessories or parts from
other manufacturers or that have not been
specifically advised by Philips.Your guarantee
will become invalid if such accessories or
parts have been used.
◗In order to avoid a hazardous situation, this
appliance must never be connected to a timer
switch.
◗Do not use the appliance if the mains cord,
the plug or other parts are damaged.
◗If the mains cord is damaged, it must be
replaced by Philips, a service centre
authorised by Philips or similarly qualified
persons in order to avoid a hazard.

ENGLISH 7
◗Thoroughly clean the parts that will come
into contact with food before you use the
appliance for the first time.
◗Do not exceed the quantities and preparation
times indicated in the table.
◗Do not exceed the maximum content
indicated on the food-processing bowl or
blender jar., i.e. do not fill beyond the top
graduation.
◗Unplug the appliance immediately after use.
◗Never use your fingers or an object (e.g. a
spatula) to push ingredients down the feed
tube while the appliance is running. Only the
pusher is to be used for this purpose.
◗Always unplug the appliance before reaching
into the blender jar with your fingers or an
object (e.g. a spatula).
◗Keep the appliance out of the reach of
children.
◗Never let the appliance run unattended.
◗The food-processing functions only work if
the dot on the screw cap is opposite the dot
on the motor unit, the dot on the bowl is
opposite the dot on the motor unit and the
line on the lid is opposite the line on the
bowl. If this is the case, the built-in safety lock
will be deblocked and the appliance can be
switched on.
◗Switch the appliance off before detaching any
accessory.
◗Always switch the appliance off by setting the
speed control to position 0.
◗Wait until moving parts have stopped running
before you remove the lid of the appliance.
◗Never immerse the motor unit in water or any
other liquid, nor rinse it under the tap. Use
only a moist cloth to clean the motor unit.
◗Remove the protective cover from the blade
before use.
◗Never use the cutter unit in combination with
the separator and sausage horn.
◗Do not attempt to grind bones, nuts or other
hard items.
◗Never reach into the tray with your fingers.
Always use the pusher.
◗Let hot ingredients cool down before
processing them in the blender jar (max.
temperature 80cC/175cF).
◗If you are processing a liquid that tends to
foam, do not put more than 1 litre in the
blender jar to avoid spillage.
◗For quantities and preparation times, please
consult the tables in these instructions for
use.
◗Note that it is not possible to use the food-
processing bowl when the blender jar is
mounted on the motor unit.
◗Noise level: Lc= 89 dB [A]
Using the appliance
Thermal safety cut-out
In order to avoid a hazardous situation, this
appliance must never be connected to a timer
switch.
If your appliance suddenly stops running:

ENGLISH8
1Pull the mains plug out of the socket.
2Let the appliance cool down for 60 minutes.
3Put the mains plug in the socket.
4Switch the appliance on again.
BPlease contact your Philips dealer or an authorised
Philips service centre if the automatic thermal cut-
out system is activated very often.
Food-processing bowl
The food-processing bowl only works if the
blender jar is not mounted on the motor unit and
if the screw cap has been screwed onto the
motor unit in such a way that the dot on the
screw cap is directly opposite the dot on the
motor unit.
C1Mount the bowl on the food processor by
turning the handle in the direction of the
arrow until you hear a click.
C2Put the lid on the bowl.Turn the lid in the
direction of the arrow until you hear a
click (this requires some force).
1
CLICK 2
12
CLICK
Built-in safety lock
The motor unit, the bowl and the lid have been
provided with marks.The appliance will only
function if the dot on the bowl is directly
opposite the dot on the motor unit.
C1Make sure that the line on the lid and the
line on the bowl are directly opposite each
other.When this is the case, the projection
of the lid will complete the shape of the
handgrip.
Feed tube and pusher
C1Use the feed tube to add liquid and/or
solid ingredients. Use the pusher to push
solid ingredients through the feed tube.
C2You can also use the pusher to close the
feed tube in order to prevent ingredients
from escaping through the feed tube.
Metal blade
The metal blade can be used for chopping, mixing,
blending and pureeing.
The cutting edges of the blade are very sharp
Avoid touching them!
CLICK

ENGLISH 9
C1Remove the protective cover from the
blade.
C2Put the tool holder in the bowl and place
the blade on the tool holder that stands in
the bowl.
3Put the ingredients in the bowl.
BPre-cut large pieces of food into pieces of approx.
3 x 3 x 3 cm. Put the lid on the bowl.
4Put the pusher in the feed tube.
C5Set the speed control to maximum speed
(position 2).
- The process continues until the speed control
is set to position 0 (off).
◗Set the speed control to position 1 to
decrease the speed.
Tips
◗When you chop onions, use the pulse setting
several times to prevent the onions from
becoming too finely chopped.
◗Do not let the appliance run too long when
you are chopping (hard) cheese.The cheese
will become too hot, will start to melt and
will turn lumpy.
◗Do not use the blade to chop very hard
ingredients like coffee beans, nutmeg, turmeric
and ice cubes, as this may cause the blade to
get blunt.
If food sticks to the blade or to the inside of the
bowl:
1Turn the appliance off.
2Remove the lid from the bowl.
3Remove the ingredients from the blade or
from the wall of the bowl with a spatula.
Inserts: slicing and shredding insert
Never process hard ingredients like ice cubes
with the inserts.
The cutting edges of the inserts are very sharp
Avoid touching them!
C1Put the desired insert in the insert holder.
C2Place the insert holder onto the tool
holder that stands in the bowl.
3Put the lid on the bowl.
4Put the ingredients in the feed tube.
BCut large ingredients into pieces that fit into the
feed tube.
1
2
CLICK

ENGLISH10
C5Fill the feed tube evenly for the best
results.
BWhen you have to slice or shred large amounts of
food, process only small batches at a time and
empty the bowl regularly between the batches.
C6Set the speed control to maximum speed
(position 2).
The process continues until the speed control is
set to position 0 (off).
◗Set the speed control to position 1 to
decrease the speed.
C7Press the pusher lightly onto the
ingredients in the feed tube.
◗If you are shredding soft vegetables or fruits,
you can decrease the speed by setting the
speed control to position 1 to prevent the
shredded vegetables and fruits from turning
into puree.
C8To remove the insert from the insert
holder, take the insert holder in your
hands with its back pointing towards you.
Push the edges of the insert with your
thumbs to make the insert fall out of the
holder.
Kneading accessory
The kneading accessory can be used for kneading
bread dough and for mixing batters and cake
mixtures.
C1Put the bowl on the motor unit and place
the kneading accessory onto the tool
holder that stands in the bowl.
2Put the ingredients in the bowl and fasten
the lid onto the bowl. Place the pusher in
the feed tube to prevent ingredients from
escaping through the feed tube during the
kneading process.
C3Set the speed control to maximum speed
(position 2).
See the table for the appropriate processing
times.
Emulsifying disc
You can use the emulsifying disc to prepare
mayonnaise, to whip cream and to whisk egg
whites.
C1Put the emulsifying disc onto the tool
holder that stands in the bowl.
2Put the ingredients in the bowl and put the
lid on the bowl.