PICOTE MAXI MILLER POWER + 18/18 Use and care manual

We now have resellers in the U.S., Europe & Australasia.
Locate your reseller at picotesolutions.com
These instrucons are for your personal safety. Always ensure that you
have read and understood these instrucons before using the machinery.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
MAXI MILLER
POWER +
MODEL: MAXI MILLER
POWER + 18/18
OPERATION
& SAFETY
MANUAL

Picote Maxi Miller Power+ 18/18
TOPIC PAGE
Safety Warnings & Symbols, Safety Requirements 3
Environmental, Transport, Storage & Disposal 6
General Informaon 7
Technical Data 8
Intended Use 8
Available Tooling 8
Operang Instrucons 9
Starng & Using the Machine 9
Digital Control Box 10
Troubleshoong 11
Voltage & Power Supply, Emergency Stop 12
Electrical requirements—Electrical set up, Electric Diagram 13
Noise Levels, Vibraons & Emissions 14
CE Declaraon of Conformity 15
Maintenance Program 16
Warranty Periods 16
Maintenance 17
Servicing the Flexible Sha & its Outer Casing 17
Changing the Flexible Sha 18
Assembly Under Hand Guard 18
Flexible Sha Extension 19
Changing Oil in the Motor & Bevel Gear 19
Accessories & Spare Parts 19
Praccal Tips & Safety Advice 21
Troubleshoong Flowchart 23
Warranty Policy & Procedure 24
Table of Contents
www.picotesoluons.com Picote Soluons Oy Ltd
2
To watch praccal demonstraon videos, or to download an electronic copy of these Instrucons, please
visit www.picotesoluons.com. Please note that videos are not intended as a replacement or alternave
to this operang and safety manual, but only as an addional learning tool.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
SAFETY INFORMATION
This section contains important safety information. Failure to
comply could result in serious injury or death.
Safety Symbols
Personal Protective Equipment (PPE)
Always use Personal Protective Equipment when using the Maxi Miller Power+, includ-
ing suitable overalls / protective clothing & footwear and the following:
Always wear suitable eye protection when using the Maxi Miller Power+ to
prevent sewage, chemicals or other dust from irritating your eyes.
Always wear suitable ear protection when using the Maxi Miller Power+ to
prevent any hearing loss.
Always wear suitable cut-resistant gloves when using the Maxi Miller Power+ to
prevent any hand injuries. Any open injuries or skin irritations should be cov-
ered at all times to avoid contact with sewage, chemicals or dust.
Always wear a suitable ventilation mask when using the Maxi Miller Power+ to
prevent any resin dust from being inhaled or consumed, which can cause occupa-
tional asthma or dermatitis as well as eye irritation.
Danger risk of serious injury from rotating parts, follow instructions.
Danger risk of serious injury, follow instructions.
Danger risk of serious injury or death by electrocution, follow instructions.
Danger risk of serious injury from hot parts, follow instructions.
Safety symbols are used throughout this manual to draw attention to potential hazards.
Danger risk of serious injury or death by electrocution, follow instructions.
3Picote Soluons Oy Ltd www.picotesoluons.com
Danger do not touch. Risk of injury, follow instructions.

Dust produced can be dangerous to your health, inflammable or explosive.
Make sure the drain pipe has been opened and ventilated to stop any gases
forming in the lateral drain where the work takes place.
Before assembly, use, replacement of parts or maintenance, unplug the Picote
milling machine from its power socket.
High voltage. Failure to comply may lead to serious injury in-
cluding electric shock or injury from rotating parts!
Always remember
Safety Symbols cont.
Safety symbols are used throughout this manual to draw attention to potential hazards.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
www.picotesoluons.com Picote Soluons Oy Ltd
4

1. Always wear eye and ear protecon as well as protecve gloves. Other personal protecve equipment, such as
respirator mask, gloves and overalls should be worn when necessary. Dust produced when working can be danger-
ous to your health, inammable or explosive. Always wear appropriate protecve equipment.
2. Make sure the pipe has been opened and venlated to stop any gases forming in the lateral drain where the work
takes place. Always ensure the pipe is grounded/earthed to prevent stac electricity.
3. Always ensure that the machine is fully turned o and unplugged before inspecon, maintenance, or installing
any accessories to the machine. Always follow the instrucons in the manufacturer’s manual.
4. Before each use inspect the machine carefully for any potenal break or damage. Change damaged parts
immediately. It is especially important to check the end of the exible power sha for any signs of wear and tear,
and repeat the process for the outer casing. Remove damaged parts by cung the power sha shorter (min. 50
mm/2”) if steel strings of the power sha are broken near the end of the power sha.
5. When in use, it is very important that the machine is stable and on an even surface at all mes. Working posion is
horizontal and lying at.
6. Never leave the machine running unaended. Always hold the cable with both hands when operang the
machine.
7. Do not touch the Cuer or Grinding Chains immediately aer use; they may be hot and could burn your skin.
8. If the working environment is extremely hot and humid (less than 95% is acceptable), or badly polluted by conduc-
ve dust, always use a residual current device in main power source to ensure the safety of the operator.
9. Make sure that the job locaon is well venlated before grinding or drilling. Always use a vacuum extracon system
in the pipe to remove dust. The operator must wear a respirator mask.
10. Ensure that the venlaon openings are kept clear when working in dusty condions. If it should become necessary
to clear dust, rst unplug the machine. Avoid damaging internal parts.
11. Do not use the machine on any materials containing asbestos.
12. Never touch rotang parts. Do not stand on the machine.
13. Only use this machine with the accessories and spare parts oered by the manufacturer. Accessories and spare
parts should only be used in the manner intended and as described by the manufacturer.
14. Only operate the foot pedal or OPC as instructed. Never place anything on it in place of a foot.
15. Do not change or touch the controls or wirings of the motor or frequency transformer.
16. Do not extend the sha by more than one extension (11m/36). Use only Picote Soluons sha extension and con-
nector.
5Picote Soluons Oy Ltd www.picotesoluons.com
This secon contains important safety informaon. Failure to comply could result in serious injury.
SAFETY REQUIREMENTS
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
Always read all safety warnings and instrucons. Failure to follow warnings and instrucons may
result in electric shock, re and/or serious injury.

17
6Picote Soluons Oy Ltd www.picotesoluons.com
TRANSPORT
Maxi Miller Power+ should be transported in car or other vehicle laid down and secured with ratchet straps to prevent
any sudden movements or accidents caused by hard braking or accident.
Never transport machine with tool aached to the sha.
If using pick-up or trailor to transport Picote milling machines, cover the unit to protect it from raining water and dust.
STORAGE
It is recemmended that milling machines are stored indoors protected from rain and sunlight and in constant ambient
temperature. Best way to store the machines is in the same box that the machine has been shipped.
If Maxi Miller Power+ will be stored in colder environment than +10 oC (50 oF ), the milling machine should be stood at
room temperature for 24hours before use.
If Maxi Miller Power+ has been stored for long periods of me (over 2-3 months), it should be checked and tested accor-
ding to maintence program before use.
This secon contains important safety informaon. Failure to comply could result in serious injury or death.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
DISPOSAL
Maxi Miller Power+ motor, control box, electric wires and axle package including slip ring can be disposed in Europe at
Waste Electrical and Electronic Equipment (WEEE) collecon points. Miller frame, reel and sha can be recycled in me-
tal waste collecon points. Outer casing of the sha can be disposed of as plasc waste.
Always follow the local waste handling rules and regulaon.
ENVIRONMENTAL
Operaonal Ambient Temperature Range: -10...50 oC (14...122 oF) frost and condensaon free
Storage Ambient Temperature Range: -20...60 oC (-4...140 oF) frost and condensaon free
Maximum Altude: 2000m (6500 ). Derate above 1000m: 1% / 100m
Maximum Humidity: 95% non-condensing

Picote Maxi Miller Power+ 18/18
6
3
7
8
10
GENERAL INFORMATION
When in use, always lay the machine down horizontally on the oor as
shown above. When not in use some non-toxic Picote Flexible Sha
www.picotesoluons.com Picote Soluons Oy Ltd
7

Picote Maxi Miller Power+ 18/18
TECHNICAL DATA
Size
(mm/inches)
Range
(m/feet)
Diameter
(mm/inches)
Rotang
speed (rpm)
Voltage and
power rang
(V/kW)
Weight
(kg/lb)
Sha
(mm/inches)
Power
Source
IP
Class
1150x854x489
/45x34x19
20 / 65 DN150-225
*DN75-225
**DN150-300
500-1500 380 - 480V /
3.0 kW
129 / 28418 / ¾ Electric
3-phase
Motor
54
INTENDED USE
This machine is intended for the following uses;
1. Cleaning and maintenance of pipes, sewers and drains by grinding.
2. Descaling pipes
3. Reinstang branches in pipes, sewers and drains by drilling and grinding.
4. Cung excess cured-in-place (CIPP) linings.
5. Removing deformed or collapsed CIPP linings.
6. Removing concrete or lime scale deposit from pipes, sewers and drains.
Always follow the manufacturer’s instrucons when installing and using the machine with accessories.
*for straight pipes
**for descaling/cleaning
3
7
8Picote Soluons Oy Ltd www.picotesoluons.com
AVAILABLE TOOLING
Original Chain
Cyclone Chain
Original Tornado Chain
Cyclone Tornado Chain
Smart Spider Power+
Twister+
Smart Crusher
Twister+ Concrete Remover
Smart Cuer™
Please check Picote Soluons Quick Cleaning Guides
and Tool Manuals for more detailed informaon.

Before installing Picote tools, always make sure that the machine is fully turned o and unplugged from
the power source.
• Always round o the sharp edges of the sha to avoid cuts and to make it easier to insert
the sha into the tool to be used.
• Check that there is the correct length of exible sha without its plasc casing at the end of
the exible sha. Check that all screws have been loosened so that the sha can be easily in-
serted inside the tool. Posion the sha inside the tool as far as it will go. Tighten the screws. Consult accessory
manuals (cuers & grinding chains) for detailed informaon.
• Always check that the unit is set to rotate in the desired direcon. The natural and intended rotaonal direcon
of the sha is clockwise (=forward), due to its fabricaon. When used clockwise the torque is at its opmum.
• An-clockwise (=reverse) rotaon direcon is strictly for temporary use only! It may result in sha failure.
While in operaon:
• Always lay the machine down horizontally on the oor.
• During drilling, grinding and cung processes, always use a separate vacuum extracon system in the drain to
remove dust.
OPERATING INSTRUCTIONS
STARTING & USING THE MACHINE
1. Check the rotaonal direcon of the sha and the rpm. The rotaonal direcon is checked using the for-
ward/reverse switch on the control unit (forward or reverse). The control of the rotaonal speed is also
located in the control unit. The rotaonal speed increases when the speed control is turned clockwise.
2. Place the tool inside the pipe.
3. Turn on the power switch.
4. Release the Red Emergency Buon (if it’s pressed down).
5. The machine starts when the OPC foot pedal is pressed down. Always hold the exible sha rmly while
operang the machine.
6. Rotang the tool makes it easier to move the tool forward inside the pipe.
7. Take all the sha out from the reel when working to increase the force transferred to the tool.
8. The machine has an Operator Presence Control or ‘OPC’. When the control is not held down, the machine
stops. The machine can also be stopped by pushing the Emergency Stop down, rotang the power switch
to O, unplugging the machine or rotang main frame on/o switch to O.
9. The life span of the sha outer casing can be prolonged by using Sleeves with Bearings designed for the
outer casing.
There is a display on the frequency transformer. The following messages may occur:
Stop The Maxi Miller Power Plus is ready and waing for OPC acvaon
. . . . The Maxi Miller Power Plus is using more current than nominal current
E-trip The Maxi Miller Power Plus is overloaded to the point that the power will be cut o momentarily. Li
your foot o the pedal and press the pedal down again to connue. Avoid overloading the motor.
Display messages
www.picotesoluons.com Picote Soluons Oy Ltd
9
This secon contains important safety informaon. Failure to comply could result in serious injury.

DIGITAL CONTROL BOX
Parameters of your Maxi Miller Power+ have been pre-set by the manufacturer. Picote Soluons has
no liability for failures or accidents caused by tampering with or changing of the sengs by end user.
Control box is pre-programmed and requires no addional adjustments. Opening the box or changing
the factory sengs may cause damage and will void the warranty.
The Navigate buon (2) can be pressed to see the rotaonal speed (rpm), the amount of current send
to motor (A), power generated in motor (kW) and power frequency of motor (Hz). Do not hold the
buon down connually.
9
Picote Maxi Miller Power+ 18/18
10 Picote Soluons Oy Ltd www.picotesoluons.com

www.picotesoluons.com Picote Soluons Oy Ltd
11
TROUBLESHOOTING
The control box of the Maxi Miller Power + will show fault codes according to dierent problems which the ma-
chine may encounter during use. Please check from the list below the most common fault codes of Maxi Miller
Power + control box. If other code than below is received or fault does not amend, please write down the error
code and contact your reseller.
Picote Maxi Miller Power+ 18/18
Fault Code Description Suggested Cause
no-FLtNo Fault Not required
0-1Output over current Instantaneous over current on the drive output. Excess load or shock load on the motor.
Note: Following a trip, the drive cannot be immediately reset. A delay time is inbuilt, which al-
lows the power components of the drive time to recover to avoid damage.
1 _t-trP Motor thermal overload The drive has tripped to prevent damage to the motor.
Try not to overload motor. Ensure sufficient cooling air is free to circulate around the motor and
that the entry and exit vents are not blocked or obstructed.
P5-trp Power stage trip Check for short circuits on the motor and connection cable.
0-volt Over voltage on DC bus Check the supply voltage is within the allowed tolerance for the drive.
U-volt Under voltage on DC bus The incoming supply voltage is too low. This trip occurs routinely when power is removed from
the drive. If it occurs during running, check the incoming power supply voltage and all com-
ponents in the power feed line to the drive.
0-tHeatsink over temperature The drive is too hot. Check the ambient temperature around the drive is within the drive specifi-
cation (+50°C/+122F) . Ensure sufficient cooling air is free to circulate around the drive.
Increase the panel ventilation if required. Ensure sufficient cooling air can enter the drive, and
that the bottom entry and top exit vents are not blocked or obstructed.
U-tUnder temperature Trip occurs when ambient temperature is less than -10°C/+14F. Temperature must be raised
over -10°C/+14F in order to start the drive.
E-trip External trip Normally closed contact has opened for some reason. Check if the motor is too hot.
FLt-dc DC bus ripple too high Check incoming supply phases are all present and balanced.
P-L055 Input phase loss trip Check incoming power supply phases are present and balanced.
h 0-1Output over current Check for short circuits on the motor and connection cable.
Note: Following a trip, the drive cannot be immediately reset. A delay time is inbuilt, which al-
lows the power components of the drive time to recover to avoid damage.
dAtA-FInternal memory fault (IO) Press stop-key. If fault persists, consult Picote Solutions.
dAtA-EInternal memory fault
(DSP)
Press stop-key. If fault persists, consult Picote Solutions.
Fan-FCooling Fan Fault Consult Picote Solutions.
0-hEAt Drive internal temperature
too high
Drive ambient temperature too high, check adequate cooling air is provided. Increase the panel
ventilation if required. Ensure sufficient cooling air can enter the drive, and that the bottom entry
Out-FOutput fault Indicates a fault on the output of the drive, such as one phase missing, motor phase currents
not balanced. Check the motor and connections.

Picote Maxi Miller Power+ 18/18
VOLTAGE & POWER SUPPLY
Ensure that the supply voltage is correct. The voltage of the power source must be within the voltage
range given on the nameplate of the machine.
The machine should be connected only to a 380-480 V power supply as indicated on the nameplate,
and can only be operated on three-phase AC supply rated for at least 16 A current. The machine has
been double sealed according to European standards. The power source has to be grounded. The fre-
quency transformer of the motor can cause residual current device to go o. If this happens frequently, change
the power source to one with slower residual current device. Residual current device should be type A and resid-
ual current permission should be 30 mA. Use only residual current devices which are permied in power feed
from main power source.
SAFETY FEATURES
There is a safety gear with a Lock/Emergency Stop Buon on the machine. The power supply to the
motor is cut o when the Emergency Stop Buon is pushed. Always make sure the Emergency Stop
Buon is pressed or completely unplug the machine when the machine accessories (e.g. Cuer or Grind-
ing Chains) are not inside the drain. An addional on/o switch is located in the main frame of the ma-
chine for increased safety of operaon.
The machine has an operator presence control or ‘OPC’. When the control is not held down, the machine stops.
OPC is the most important safety device of the Miller machines. Never place anything on the place of a foot (for
example a brick).
Power plugs
For safety purposes, this machine may be equipped with a specialty plug. If the plug does not t securely or match
the outlet, do not force it — contact an electrician to determine the required power supply. Never alter the plug in
any way. Use the plug with an extension cord only if it can be fully inserted into the cord’s socket. Use the Maxi
Miller Power Plus with a heavy duty extension cord only. Extension cord lead minimum thickness is 2.5 mm2 / 12
AWG up to 10 m.
If a power generator is used, make sure that power rang is sucient, at least 8 kVA measured, connuous out-
put. Only clean and stabile sine wave is accepted. Contact your reseller or Picote Soluons technical support for
more informaon. 400 V The Maxi Miller Power Plus is equipped with
a 5-pin 400 V / 16 A plug. The plug ts into a three-
phase 400 V socket shown in the picture on the le.
Power cable lead minimum thickness 2.5 mm2 / 12
AWG.
The Maxi Miller Power Plus must be supplied with
sucient power and proper current rang. Minimum
lead thickness for an extension cord is 2.5 mm2 / 12
AWG.
If power generator is used, minimum of 8 kVA is
required. An adapter is provided to connect the Maxi
Miller Power Plus into a 5-pin 400 V / 32 A socket.
Other adapters may be necessary for generator
connecons.
11
The machine has an automac safety clutch which shuts down the machine when the tools get stuck.
12 Picote Soluons Oy Ltd www.picotesoluons.com

Picote Maxi Miller Power+ 18/18
ELECTRICAL REQUIREMENTS— ELECTRICAL SET UP
Electrical shock can cause serious or fatal injury. Only qualied personnel should install, maintain or troub-
leshoot this equipment. Picote Soluons recommends that a properly trained electrician be available to wire
a power distribuon box to whatever power source is available. In the case where a generator is required, a
minimum power requirement of 8 kVA 3 Phase 480 volt is necessary.
The Power Plus has a 3 phase power conguraon. It uses a 4 mm2 / 10 AWG 4 wire cord (3P + E).
Be sure the system is properly grounded before applying power. Do not apply power before you ensure that
grounds are connected. Electrical shock can cause serious or fatal injury. Follow the Naonal Electrical Code
(NEC) and local codes for the safe installaon of the equipment.
Do not operate the Maxi Miller Power+ unl you are sure that you are completely familiar with the safe opera-
on of the machine, all accessories and safety equipment. Improper use can lead to severe injury. The user ma-
nual denes proper use of this equipment.
Contact Picote Soluons if you do not understand any procedure or operaon concerning this equipment or
the user manual.
ELECTRIC DIAGRAM
www.picotesoluons.com Picote Soluons Oy Ltd
13

NOISE LEVEL & EMISSIONS
The typical A-weighted noise level determined according to EN60745:
Sound pressure level (LpA): 85 dB (A)
Sound power level (LWA): 98 dB (A)
WEAR EAR PROTECTION
Emissions during actual use of the machine can dier from the declared values depending on the ways that the
machine is used. Safety measures to protect the operator should be determined by actual condions, taking into
account all aspects of the operang cycle (such as when the machine is switched o and when it is running idle).
Due to connuing product development, the specicaons herein are subject to change without noce.
13
This secon contains important safety informaon. Failure to comply could result in serious injury or loss
of hearing.
Hand vibraon levels depend on the tool head distance to user and working condions. Vibraon levels in here
have been measured in lining removal work. Vibraon has been determined according to ISO-5349 and EU-
direcve 2002/44/EG. In table above are shown safe daily exposure me for user.
Exposure Acon Value (EAV) 2,5 m/s2
Exposure Limit Value (ELV) 5,0 m/s2
VIBRATION
Tooling EAV ELV
Smart Sweeper with drill head 1h 5 min 4 h 22 min
Smart Sweeper with Crasher head 2 h 47 min 11 h 8 min
Twister+ 10 h 46 min Over 24 h
Premium Cyclone Chain 15 h 58 min Over 24 h
Smart Crusher DN100 55 min 3 h 38 min
Smart Cuer™ DN150 9 h 58 min Over 24 h
14 Picote Soluons Oy Ltd www.picotesoluons.com
Values in the table have been measured in controlled environment in Picote Training facilies during pipe cleaning or liner
removal work. Liner material in tests was polyester which epoxy resin hardened and me-cured hard.

We Picote Soluons Oy Ltd as the responsible manufacturer, declare that the following Picote Soluons Oy Ltd
machine:
Maxi Miller Power +
Model No: MXM P+ 18/20
is of series producon and
Conforms to the following EU Direcve:
2006/42/EC
And is manufactured in accordance with the following standards or standardized documents:
EN60745
The technical documentaon is kept by our authorised representave in Europe who is:
Picote Soluons Oy Ltd, Urakoitsijane 8
06450 Porvoo, Finland
1st June 2017
CE DECLARATION OF CONFORMITY
Katja Lindy-Wilkinson
C.E.O.
Picote Soluons Oy Ltd
Urakoitsijane 8, 06450 Porvoo, Finland
www.picotesoluons.com Picote Soluons Oy Ltd
15

MAINTENANCE PROGRAM
16 Picote Soluons Oy Ltd www.picotesoluons.com
WARRANTY PERIODS
Picote Soluons grants limited warranty for certain machines, equipment & components. Read more detailed in-
formaon on page 23 Picote Warranty Policy and Procedure.
Months
Maintenance task 3612 24
Tightness of motor xing II
Alignment of motor & gear box II
Condion of frame II
Condion of wheels & rubber bushes II
Condion of control box II
Condion of electric cables IIII
Condion of electrical connecons IIII
Lubricate Sha PPPP
Operaon of E-Stop IIII
I: Inspect, x or replace if needed.
P: Perform, replace if needed.
R: Replace
Service Period 3 months 6 months 1a
A
B
C
AMilling machine & spare parts, except
BElectric motors
CService Centre repair work

MAINTENANCE
1. Before performing any maintenance always check that the machine is fully turned o and
unplugged.
2. Carefully inspect the exible sha and its casing on a regular basis to ensure that there are no signs of wear
and tear. Change the exible sha and casing as and when required.
3. For safety and eciency, always keep the machine and its motor, drive unit, venlaon and cooling slots clean.
4. Check that the screws for the sha socket are securely ghtened.
5. Check that all the bolts and screws on the machine are securely ghtened.
6. It is recommended that the oil in the bevel gear should be changed about every 12 months. Use regular oil in-
tended for gearboxes. See oil change instrucons on page 17.
SERVICING THE FLEXIBLE SHAFT & ITS OUTER CASING
Prior to shipping the exible sha is pre-treated with liquid Picote Flexible Sha Lubricant (non-hazardous) and
the casing replaced. Always inspect the condion of the sha and its outer casing regularly. Also, inspect at least
every h working day that the sha is properly aached under the hand guard at the machine end. If the twine
of the sha has opened from one end to the other so that there are visible holes in the sha, the enre sha has
to be replaced.
Lubricant can be added between the exible sha and its outer casing when the sha is removed from the
machine. In order to add lubricant the cable needs to be removed from the reel. The sha needs to be taken out
from outer casing about 1 –1,5m (3-5) and lubricant needs to be added on the other side inside the cavity. No
more than 50ml/50g/1.5oz will be required for the enre sha. Too much lubricant can cause strain on the cab-
le. Aer lubricant is poured, the free sha end should be pushed through the outer casing. The sha will push
the lubricant evenly inside the outer casing. Connect the sha to the machine and rotate with low rotaon speed
so sha will push excess lubricant outside. Use a mat to protect the work area under the machine to prevent da-
mage to oors.
Keeping the sha well lubricated will prolong its life span and decrease the fricon caused by the sha when it
turns around. Lower fricon will reduce the load on the motor.
If preferred, the sha can be taken out of its outer casing for lubricaon.
Appropriate oil to use: Picote Flexible Sha Lubricant (available from your reseller)
17 Picote Soluons Oy Ltd www.picotesoluons.com

CHANGING THE FLEXIBLE SHAFT
Only use the sha and its outer casing specied by the manufacturer of the machine. Order the replacement sha
from your reseller. The exible sha is pre-treated with Picote Flexible Sha Lubricant and the casing replaced
prior to shipping.
1. Loosen the bolts holding the hand guard and strain relief spring. Remove hand guard.
2. Loosen the screws in the sha socket that hold the sha. Remove strain relief spring. Pull the old sha out
from the machine.
3. Insert new sha. When inserng the sha inside the sha socket, verify that the sha goes all the way to the
end. Tighten the screws.
4. Make sure that strain relief is aached and contacts the sha socket before aaching the hand guard.
5. Mount the hand guard. Tighten the bolts to 8 Nm.
Look at the assembly under hand guard from below.
ASSEMBLY UNDER THE HAND GUARD
www.picotesoluons.com Picote Soluons Oy Ltd
18

17
CHANGING OIL IN THE ANGLE GEAR
FLEXIBLE SHAFT EXTENSION
Flexible extension shas are available for the Maxi Miller Power+ in lengths of 11 metres (36). Do not extend
the sha by more than one extension and only use a Picote Soluons sha extension and connector.
Before aaching or removing the sha extension always make sure that the machine is fully turned o and un-
plugged.
1. Machine as far as possible with the exible sha before ng the extension.
2. Remove the exible sha from the pipe.
3. Push the extension down the pipe and then connect onto the exisng exible sha using a sha connector.
4. You can then carry on machining.
Note: for vercal pipes connect the extension onto the exisng exible sha before pushing the extension down
the pipe.
The oil should be changed aer every 1000 hours of use or 12 months.
1. Dismount the gear guard and the hand guard.
2. Remove the sha socket from the sha.
3. Loosen the bolts holding the angle gear.
4. Pull the angle gear away from the motor following the axle of the motor.
5. When the angle gear has been dismounted, loosen the oil screw (there is only one screw on the gearbox).
6. Pour the old oil out and add the new oil.
7. Reassemble the angle gear by repeang the previous steps in reverse order.
Appropriate oils to use: Shell omala 100 or Agip blasia 100 or Tamoil ep 100
Amount of oil: 0,042 kg / 1.4815 oz
Window of change: aer every 3000 hours of use or 12 months
19 Picote Soluons Oy Ltd www.picotesoluons.com
If there is problem that you cannot resolve with this manual, please consult your Picote
Reseller or Picote Solutions.

MAXI MILLER POWER+
3570032018 Maxi Miller Power + 18/18 400v
3570032018UK Maxi Miller Power+ 18/18 400v UK
3570032018US Maxi Miller Power+ 18/18 400v US
1313002185 Sha Connector 18/18
9570000034-1Strain Relief Maxi Power+
1312021180020 Maxi Power+ spare sha 20.5m
1312021180011 Maxi Power+ extension sha 11m
93212520180SB Sleeve for 18mm outer casing
1350000020 Picote Flexible Sha Lubricant 0.5 liters
1350000021 Picote Flexible Sha Lubricant Package, includes 6 boles
SPARE PARTS
20
ACCESSORIES
Only use the Picote Soluons accessories and aachments with the machine described in this
operaons manual. The use of other accessories or aachments could present a risk of injury or
death. The accessories or aachments should only be used in the proper and intended manner, and always fol-
low the instrucons in the Picote Soluons manuals.
ADDITIONAL TOOLS
1100400001 Bearing Cleanser
1350000005 Pliers
1350000007 Cuer for Steering Wire
1350000018 Sha Rounder
1350000006 Sheath Cuer 1
1350000011 Sheath Cuer 2 (Sha inside outer casing)
1350000012 Cuer for Side Grinding Panels
1350000008 Hex Key 4mm
1350000009 Hex Key 3mm
1350000010 Hex Key 2.5mm
1350000013 Combo Hex Key 1-6mm
1350000001 Wrench 8mm
www.picotesoluons.com Picote Soluons Oy Ltd