Pioneer AVH-P5950DVD User manual

English Français Italiano Nederlands PyÒÒÍËÈ
ENG/MASTER COVER 98 INST
AVH-P5950DVD
This product conforms to new cord colors.
INSTALLATION MANUAL
INSTALLATION MANUAL
<CRD4215-A> 1

1
Contents
Connecting the Units ................................ 1
Connecting the power cord .............................. 3
When connecting to separately sold power
amp ............................................................ 5
When connecting with a rear view camera ...... 7
When connecting with a multi-channel
processor .................................................... 8
Connecting and installing the optical cable
connection box .......................................... 9
When connecting the external video
component and the display ...................... 10
Installation ................................................ 11
DIN Front/Rear-mount .................................... 11
DIN Front-mount ............................................ 12
DIN Rear-mount .............................................. 13
Fastening the front panel ................................ 14
Installing the remote control unit .................... 14
WARNING
•To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or TV
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.
•In some countries or states the viewing of
images on a display inside a vehicle even by
persons other than the driver may be illegal.
Where such regulations apply, they must be
obeyed and this unit’s DVD features should
not be used.
CAUTION
•PIONEER does not recommend that
you install or service your display your-
self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho-
rized Pioneer service personnel.
•Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
•Do not drill a hole into the engine com-
partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.
•It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.
•Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
•Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.
WARNING
LIGHT GREEN LEAD AT POWER CONNEC-
TOR IS DESIGNED TO DETECT PARKED
STATUS AND MUST BE CONNECTED TO
THE POWER SUPPLY SIDE OF THE PARK-
ING BRAKE SWITCH. IMPROPER CONNEC-
TION OR USE OF THIS LEAD MAY VIO-
LATE APPLICABLE LAW AND MAY
RESULT IN SERIOUS INJURY OR DAMAGE.
ENG/MASTER 96 INST
<CRD4215-A> 2
Connecting the Units

English Français Italiano Nederlands PyÒÒÍËÈ
<CRD4215-A> 3
ENG/MASTER 96 INST
2
Note:
•This unit cannot be installed in a vehicle with-
out ACC (accessory) position on the ignition
switch.
•Use this unit in other than the following condi-
tions could result in fire or malfunction.
—Vehicles with a 12-volt battery and negative
grounding.
—Speakers with 50 W (output value) and 4
ohm to 8 ohm (impedance value).
•To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
—Disconnect the negative terminal of the bat-
tery before installation.
—Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.
—Place all cables away from moving parts,
such as gear shift and seat rails.
—Place all cables away from hot places, such as
near the heater outlet.
—Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
—Cover any disconnected cable connectors
with insulating tape.
—Do not remove RCA caps if RCA cables are
not used.
—Do not shorten any cables.
—Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
—Use a fuse of the rating prescribed.
—Never wire the speaker negative cable direct-
ly to ground.
—Never band together multiple speaker’s nega-
tive cables.
•Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
•Never connect blue/white cable to external
power amp’s power terminal. Also, never con-
nect it to the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
•IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
•Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.
•Cord function may differ according to the
product, even if cord color is the same. When
connecting this system, be sure to check all
manuals and connect cords correctly.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F

3
Connecting the Units
Connecting the power cord
ENG/MASTER 96 INST
<CRD4215-A> 4
+
≠
+
≠
+
≠
+
≠
+
≠
14 cm
Bl
Co
am
(m
W
ch
u
le
(b
Yellow
Connect to the constant 12 V supply terminal.
Fuse (10 A)
Fuse resistor
Red
Connect to terminal controlled by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Fuse resistor
Orange/white
Connect to lighting switch terminal.
IP-BUS input
(Blue)
IP-BUS cable
Multi-CD player
(sold separately)
15 cm
This product
15 cm
Antenna cable
Left Right
Front speaker Front speaker
Rear speaker or
Subwoofer (4 Ω)
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
W
a
c
Violet
Violet/black
Not used.
Green
Green/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit.
Do not connect anything to Green and Green/black leads.
Subwoofer (4 Ω)
×2
Rear speaker or
Subwoofer (4 Ω)

English Français Italiano Nederlands PyÒÒÍËÈ
4
ENG/MASTER 96 INST
<CRD4215-A> 5
iPod with Dock
Connector
Dock connector
Interface cable (e.g., CD-I200)
(sold separately) 2 m
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note:
• The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Yellow/black
If you use equipment with Mute function, wire this lead to
the Audio Mute lead on that piece of equipment. If not,
keep the Audio Mute lead free of any connections.
Light green
Used to detect the ON/OFF status of the parking brake. This
lead must be connected to the power supply side of the parking
brake switch.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal
(max. 300 mA 12 V DC).
Ground side
Power supply side
Parking brake
switch
When you connect the separately sold multi-
channel processor (e.g., DEQ-P7650) to this
unit, do not connect anything to the speaker
leads and system remote control
(blue/white).
Dock connector port
Gray
AUX jack (3.5 ø)
20 cm
Use a mini plug cable to
connect with auxiliary
equipment.
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Note:
• Change the initial setting of this unit (refer to the
Operation Manual). The subwoofer output of this unit
is monaural.

When connecting to separately sold power amp
5
Connecting the Units
ENG/MASTER 96 INST
<CRD4215-A> 6
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal
(max. 300 mA 12 V DC).
When you connect the separately sold multi-
channel processor (e.g., DEQ-P7650) to this
unit, do not connect anything to the speaker
leads and system remote control
(blue/white).
This product
Front output
(FRONT OUTPUT)
Rear output
(REAR OUTPUT)
Subwoofer output (SUBWOOFER
OUTPUT or DEQ OUTPUT)
When you connect the multi-channel
processor to this unit, refer to multi-channel
processor’s installation manual for the
connection method.
15 cm
20 cm

English Français Italiano Nederlands PyÒÒÍËÈ
6
ENG/MASTER 96 INST
<CRD4215-A> 7
++
≠
≠
++
++
≠≠
≠
≠
Note:
• Change the initial setting of this unit (refer to the Operation
Manual). The subwoofer output of this unit is monaural.
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Connect with RCA cables
(sold separately)
Subwoofer
Rear speaker
Perform these connections when
using the optional amplifier.
System remote control
Front speaker Front speaker
Left Right
Rear speaker
Subwoofer

When connecting with a rear view camera
When using this product with a rear view camera, automatic switching to video from a
rear view camera when the gear shift is moved to REVERSE (R) position is possible.
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
•The screen image may appear reversed.
•The rear view camera function is to be used as an aid for backing into a tight parking spot. Do not use this
function for entertainment purposes.
•Objects in the rear view may appear closer or more distant than they actually are.
<CRD4215-A> 8
ENG/MASTER 96 INST
7
Connecting the Units
Violet/white
Of the two lead wires connected to the back lamp, connect the
one in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
This product
Rear view camera input
(REAR VIEW
CAMERA IN)
You must use a camera
which outputs mirror
reversed images.
20 cm
Fuse resistor
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note:
• It is necessary to set CAMERA POLARITY properly in SYSTEM MENU when
connecting the rear view camera.
10 cm
Extension lead (supplied)
RCA cable
(sold separately)
To video output
CAUTION
Rear view camera
8 m

English Français Italiano Nederlands PyÒÒÍËÈ
When connecting with a multi-channel processor
<CRD4215-A> 9
8
ENG/MASTER 96 INST
When you connect a separately sold
DVD player to the separetely sold
multi-channel processor, the optical
cable from DVD player must be
connected to the optical cable 2 input
(OPT. IN2) of the multi-channel
processor.
This product
25 pin cable (supplied
with DVD player)
DEQ output (SUBWOOFER
OUTPUT or DEQ OUTPUT)
20 cm
Blue
Multi-CD player
(sold separately)
IP-BUS cable
IP-BUS input
(Blue)
15 cm
44 cm AV-BUS input
(Blue)
Optical cable connection box
(supplied)
IP-BUS cable (supplied with
multi-channel processor)
IP-BUS cable (supplied
with TV tuner)
AV-BUS cable (supplied
with TV tuner)
AV-BUS cable (supplied
with DVD player)
Optical cable (sold
separately)
Optical cable (supplied with
multi-channel processor)
RCA cable (supplied with
multi-channel processor)
DVD player (e.g., XDV-P650)
(sold separately)
Black
Black
Black
Blue
Hide-away unit (supplied
with DVD player)
IP-BUS cable
(supplied with DVD
player)
Black
Blue
Blue
Hide-away TV tuner
(e.g., GEX-P5750TV(P))
(sold separately)
Multi-channel processor
(e.g., DEQ-P7650)
(sold separately)
Black
Blue
Black
Black Blue
Black Blue

<CRD4215-A> 10
9
Connecting the Units
ENG/MASTER 96 INST
Connecting and installing the
optical cable connection box
WARNING
•Avoid installing this unit in locations where the
operation of safety devices such as airbags is pre-
vented by this unit. Otherwise, there is a danger of
a fatal accident.
•Avoid installing this unit in locations where the
operation of the brake may be prevented.
Otherwise, it may result in a traffic accident.
•Fix this unit securely with the velcro tape or lock
tie. If this unit is loose, it disturbs driving stabili-
ty, which may result in a traffic accident.
CAUTION
•Install this unit using only the parts supplied with
this unit. If other parts are used, this unit may be
damaged or could dismount itself, which leads to
an accident or other problems.
•Do not install this unit near the doors where rain-
water is likely to be spilled on the unit. Incursion
of water into the unit may cause smoke or fire.
Connecting the optical cable
1. Connect the optical cable and
ground lead to the main unit.
Connect the optical cable so that it
does not protrude from the unit, as
shown in the illustration. Fasten the
ground lead to the protrusion on the
back of the unit.
2. Connect the optical cable to the
optical cable connection box.
Installing the optical cable
connection box
• When installing the optical cable
connection box with the velcro
tape.
Install the optical cable connection box
using the velcro tape in the ample
space of the console box.
•When installing the optical cable
connection box with the lock tie.
Wrap the optical cable and connection
box with the protection tape and fasten
with the power code using the lock tie.
Fasten with the lock tie
Wrap with the protection tape
Velcro tape (hard)
Velcro tape (soft)
Optical cable
Screw

English Français Italiano Nederlands PyÒÒÍËÈ
<CRD4215-A> 11
10
ENG/MASTER 96 INST
When connecting the external video component and the display
•It is necessary to set AV INPUT to VIDEO in SYSTEM MENU when connecting the
external video component.
•It is necessary to set AV INPUT to S-DVD in SYSTEM MENU when connecting a
multi-DVD player.
When using a display connected to rear video output
This product’s rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING
•NEVER install the display in a location that enables the Driver to watch the DVD or Video CD
while driving.
This product
External video
component
(sold separately)
RCA cables (sold separately)
Audio input
(AUDIO INPUT)
Video input
(VIDEO INPUT)
25 cm
Display with
RCA input jacks
(sold separately)
Rear monitor output
(REAR MONITOR OUTPUT) To video input
To video output
To audio outputs
15 cm

<CRD4215-A> 12
11
ENG/MASTER 96 INST
Note:
•Check all connections and systems before final
installation.
•Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
•Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
•Do not install this unit where:
—it may interfere with operation of the vehicle.
—it may cause injury to a passenger as a result
of a sudden stop.
•Do not install the display where it may (i)
obstruct the driver’s vision, (ii) impair the per-
formance of any of the vehicle’s operating sys-
tems or safety features, including air bags, haz-
ard lamp buttons or (iii) impair the driver’s abili-
ty to safely operate the vehicle.
•The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
•Optimum performance is obtained when the unit
is installed at an angle of less than 30°.
•The cords must not cover up the area shown in
the figure below. This is necessary to allow the
amplifires to radiate freely.
•Make sure you leave enough gap between the
dashboard and the LCD panel of this unit so the
LCD panel can be opened and closed without
contacting with the dashboard.
•When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
DIN Front/Rear-mount
This unit can be properly installed
either from “Front” (conventional DIN
Front-mount) or “Rear” (DIN Rear-
mount installation, utilizing threaded
screw holes at the sides of unit chas-
sis). For details, refer to the following
illustrated installation methods.
Dashboar
d
Leave
g
a
p
LCD
p
ane
l
Do not cover this area.
30°
Installation

English Français Italiano Nederlands PyÒÒÍËÈ
<CRD4215-A> 13
12
ENG/MASTER 96 INST
Before installing the unit
•Remove the trim ring and the
mounting sleeve.
Extend top and bottom of the trim ring
outwards to remove the trim ring. And
then loosen the screws (2 mm ×3 mm)
to remove the mounting sleeve.
•When reattaching the trim ring, push
the trim ring onto the unit until it
clicks after reattaching the mounting
sleeve. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
DIN Front-mount
1. Decide the position of the side
brackets.
•When installing in a shallow space,
change the position of side brackets
(small). In this case, stick concealing
tape on parts that protrude from the
dashboard.
•If you prefer an off-set installation
in which the front panel is pushed
further back, when there is a space
available at the back of the unit, use
the side brackets (large).
Flush surface screw
(
5 mm
×
6 mm
)
Side bracket (lar
g
e
)
Flush surface screw (5 mm ×6 mm)
Side bracket (small)
Concealing tape
Mountin
g
sleev
e
Trim rin
g
Screw
(
2 mm
×
3 mm
)

13
Installation
ENG/MASTER 96 INST
<CRD4215-A> 14
2. Install the unit into the dash-
board.
Insert the mounting sleeve into the
dashboard. And then secure the mount-
ing sleeve by using a screwdriver to
bend the metal tabs (90°) into place.
DIN Rear-mount
1. Determine the appropriate posi-
tion where the holes on the
bracket and the side of the unit
match.
*1 Use binding screws (4 mm ×3 mm) only.
•When installing in a shallow space,
use the following screw holes. In
this case, stick concealing tape on
parts that protrude from the dash-
board.
*1
*1
Concealing tape
*
1
*
1
182
53 Rubber bush
Screw
Dashboard
Side bracket
Screw (2 mm ×3 mm)
Mounting sleeve

English Français Italiano Nederlands PyÒÒÍËÈ
14
ENG/MASTER 96 INST
<CRD4215-A> 15
2. Tighten two screws on each side.
Use any of binding screws (4 mm ×3
mm), binding screws (5 mm ×6 mm)
or flush surface screws (5 mm ×6
mm), depending on the shape of screw
holes in the bracket.
Fastening the front panel
If you do not plan to detach the front
panel, the front panel can be fastened
with supplied screws.
•Fix the front panel to the unit
using screws after removing the
trim ring.
Installing the remote control unit
When not using the remote control
unit, secure it with velcro tape to pre-
vent it from moving.
•Thoroughly wipe off the surface
before affixing the velcro tape.
Velcro tape (small)
(hard)
Velcro tape (small)
(soft)
Remote control unit
S
crew
s
Screw
Dashboard or
Console
Factory radio mounting
bracket

ENG/MASTER 98 <CRD4215-A> 16
連接本機
1
連接本機 ........................... 1
連接電源線 ....................... 3
連接另售的功率放大器 ............. 5
連接後視攝像頭 ................... 7
連接多通道處理器 ................. 8
光纜連接盒的連接和安裝 ........... 9
連接外部視頻組件和顯示器 ........ 10
安裝 .............................. 11
DIN前面/後面安裝 ................ 11
DIN 前面安裝 .................... 12
DIN 後面安裝 .................... 13
固定前面板 ...................... 14
安裝遙控器 ...................... 14
警告
•為避免意外事故和違反適用的法律，正在駕車
時，決不能使用前方的D V D 或電視機（另售）。
另外，後顯示器不能位於阻擋司機視線的位
置。
•在某些國家或州，即使司機以外的乘客若在車
內通過顯示幕觀看影像亦會違法。在實行這樣
法規的地方，必須依法照辦，不應使用本機的
DVD功能。
目錄
注意
•PIONEER先鋒公司建議您不要自己安
裝或維修顯示器。安裝和維修本產
品使您處於電擊或其他危險中。請
將顯示器的所有安裝和維修作業委
託給Pioneer先鋒公司授權的維修人
員。
•請用電纜夾或絕緣膠帶固定所有的
接線。不要讓任何裸露的接線曝露
在外。
•不要在引擎艙鑽孔連接本機的黃色
引線至汽車電瓶。引擎振動最終可
能會破壞從客艙通往引擎艙之處軟
線的絕緣。此處應特別小心緊固軟
線。
•將顯示器引線繞在轉向柱或變速杆
上特別危險。務必不要讓顯示器的
安裝妨礙駕駛。
•確保軟線不妨礙汽車活動部件如變
速杆、停車制動器或座椅調節機
構。
•不要截短任何引線。否則保護電路
可能起不到應有的作用。
警告
電源接口處的淺綠色引線設計用於偵測車輛停
放狀態，必須將其連接至手煞車開關的電源
側。該引線若連接或使用不當會違反適用法
律，並導致嚴重人身傷害或機器損壞。

ENG/MASTER 98
<CRD4215-A> 17
2
注意：
• 本機不可安裝在起動點火開關上沒有ACC
(附件) 位置的車輛上。
ACC位置 無ACC位置
• 使用本機時若不符合以下條件，可能會導致
火災或故障。
—裝有12伏電瓶且負極接地的車輛。
—50W（輸出值）、4Ω至8Ω（阻抗值）的
揚聲器。
• 為避免發生短路、過熱或故障，請務必遵守
以下說明。
—在安裝之前斷開電瓶的負極終端。
—請固定好軟線卡夾或膠布。為了保護軟
線，請用膠布纏住與金屬部件接觸的部
分。
—將全部軟線放置於遠離移動部件（如變速
杆和座位導軌）的地方。
—將全部軟線放置於遠離發熱之處，如靠近
加熱器通風口。
—連接電瓶時，請勿將黃色導線通過孔穴進
入引擎艙。
—請用絕緣膠帶包住所有斷開的導線接頭。
—如果不使用RCA電纜，則請勿拆除RCA保護
套。
—請勿將任何導線弄短。
—請勿切開本機電源導線的絕緣為其他裝置
供電。導線的電流容量是有限制的。
—請使用規定額定電流的保險絲。
—請勿將揚聲器負極導線直接接地。
—請勿將多個揚聲器的負極導線捆綁在一
起。
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
• 當本機打開後，將通過藍色/白色導線輸出控
制信號。請連接至外接功率放大器的系統遙
控或車輛的自動天線繼電器控制終端（最大
300mA，12V直流電）。若車輛帶有玻璃天
線，請連接至天線升壓器電源介面。
• 請勿將藍色/白色導線連接至外接功率放大器
的電源接線端。同時，也請勿將藍色/白色導
線連接至自動天線的電源接線端。否則會造
成電瓶電力耗盡或故障。
• IP-BUS接頭以顏色標記。連接的接頭顏色務
必相同。
• 黑色導線接地。請將其與其他裝置（尤其是
高電流電器如功率放大器）的接地導線分開
接地。否則，一旦這些接地導線分離，則會
造成火災或故障。
• 本機使用的接線與其他接線即使顏色相
同，其功能也可能不同。連接本機時，請
參考所有說明書進行正確連接。

ENG/MASTER 98 <CRD4215-A> 18
3
連接本機
連接電源線
+
≠
+
≠
+
≠
+
≠
+
≠
IP-BUS輸入（藍色）
IP-BUS電纜
15 cm 14 cm
多片式CD唱碟
（另售） 天線電纜 15 cm
本機
黃色
至12V常時供電終端。
紅色
至點火開關 (12V直流電) 控制的終端。
黑色（接地）
至清潔、無漆的金屬部件。
橙色/白色
接至點亮著的開關終端。
保險絲 (10A)
保險絲電阻器
保險絲電阻器
紫色/黑色
前置揚聲器
左右
綠色 紫色
綠色/黑色
前置揚聲器
白色
白色/黑色
灰色
灰色/黑色
後置揚聲器或
超低音揚聲器
(4Ω)
後置揚聲器或
超低音揚聲器
(4Ω)
使用 70 W (2Ω) 的超低音揚聲器時，確定連接本機的紫色與紫色/黑色引線。
不可將任何設備連接到本機的綠色與綠色/黑色引線。
超低音揚聲器
(4Ω)×2
未使用。
紫色/黑色
綠色 紫色
綠色/黑色

ENG/MASTER 98
<CRD4215-A> 19
4
1. 夾住引線。
連接方法
2. 用尖頭鉗夾緊。
注意︰
•停車剎車開關的位置取決於車型。詳細情況可查閱
車主的使用說明書或者可向維修店查詢。
淡綠色
用以檢測停車剎車的 ON/OFF（開/關）狀態。該引線必
須接到停車剎車開關靠電源一側。
停車剎車開關
電源側
接地側
灰色
Dock接頭埠
接口電纜
（例如：CD-I200）
（另售）
20 cm
2 m
使用微型插頭電纜與輔助
設備連接。
AUX口 (3.5 ø)
iPod附有Dock接頭
黃色黑色
如果使用有靜音功能的設備，將此引線連接到該設備的音頻靜
音引線。 如不使用，不必將此音頻靜音引線進行任何連接。
藍色/白色
至功率放大器的系統控制終端或自動天
線繼電器的控制終端（最大300mA，12V
直流電）。
在2揚聲器系統中，切勿用未連接揚聲器的引
線連接其它設備。
當您連接獨立購買的多聲道處理器(例如
DEQ-P7650)至本機時，請勿將任何設備和
揚聲器引線及本機的系統遙控器相連（藍
色白色）。
注意：
•改便了本機的原始設定（請參照本操作說明
書)。此裝置的重低音輸出為非立體聲。
Dock接頭

ENG/MASTER 98 <CRD4215-A> 20
5
連接本機
連接另售的功率放大器
本機
藍色/白色
至功率放大器的系統控制終端或自動天線繼電器的控制
終端（最大300mA，12V直流電）。
當您連接獨立購買的多聲道處理器(例如
DEQ-P7650)至本機時，請勿將任何設備和
揚聲器引線及本機的系統遙控器相連（藍
色白色）。
將多聲道處理器連接到本機上時，連接
方法請參照多聲道處理器的安裝說明
書。
15 cm
20 cm
前方輸出
(FRONT OUTPUT)
後方輸出
(REAR OUTPUT)
超低音揚聲器輸出
(SUBWOOFER OUTPUT or DEQ OUTPUT)