Pioneer DDJ-ERGO User manual

0
00
0
“TRAKTOR PRO 2”
Setup Guide

1
11
1
Before start (Important)
Setup Wizard offers a simple setup procedure for TRAKTOR PRO 2 (Ver.2.1.2. or
later).
Please follow the instructions below before starting the setup
procedures of TRAKTOR PRO 2.
・Update the DDJ-ERGO’s firmware to the latest version.
・For Windows users:
Turn on the power of DDJ-ERGO first. Then, run the TRAKTOR software.
If the TRAKTOR PRO 2 is launched before the DDJ-ERGO is powered on, the
DDJ-ASIO driver may not be recognized.
If the DDJ-ASIO driver is not recognized, turn off both the TRAKTOR PRO 2 and the
DDJ-ERGO and repeat the above procedures.
Setup procedures
* The screenshots used in this guide may be different depending on the version of
TRAKTOR PRO 2.
1. Connect the DDJ-ERGO to your computer by a USB cable and turn on the power
of the controller using ON/OFF slide switch.
2. Launch TRACTOR PRO 2 after DDJ-ERGO starts.
Note: Ensure that DDJ
Note: Ensure that DDJNote: Ensure that DDJ
Note: Ensure that DDJ-
--
-ERGO starts before launching T
ERGO starts before launching TERGO starts before launching T
ERGO starts before launching TRA
RARA
RAK
KK
KTOR
TORTOR
TOR PRO 2.
PRO 2. PRO 2.
PRO 2.
3. From the upper left "Help" menu, open "Start Setup Wizard" and click "Next."
4. When the message "Are you using an external controller?" is displayed, select
"Yes" and click "Next."
5. When the messages "Choose your manufacturer" and "Choose you model" are
displayed, select "Pioneer" and "DDJ ERGO" respectively. Then, click "Next."
6. The message "Are you using an external mixer?" is displayed. If you use one,
select "Yes" and if you do not, select "No" and click "Next."
7. When "Select your setup" is displayed, select the decks you will use and click
"Next."
Cautions
・For Windows users, DDJ-ERGO driver software is required to be installed in
advance.
・All the current settings of TRAKTOR PRO 2 will be overwritten to default
settings.

2
22
2
8. When "Finish" is displayed in the lower right corner of the wizard, click "Finish" to
complete the Setup Wizard.
9. Select [File] > [Controller Manger...]. Under [Device Setup], select the
[PIONEER_DDJ-ERGO] from [Device] menu and select the device corresponding
to the DDJ-ERGO at [In-Port] and [Out-Port].
10. The preferences settings may be overwritten to the default settings after
completing the setup wizard depending on the versions of TRAKTOR PRO 2.
When using DDJ-ERGO, the following audio settings are minimal requirements.
Please ensure that you go through the setup procedures.
(1) Audio etup
・Audio Device: PIONEER DDJ ASIO (For Windows users)
DDJ-ERGO (For Mac users)
(2) Output Routing
・Mixing Mode：Internal
・Output Monitor：
L 3:DDJ-ERGO PHONE L
R 4:DDJ-ERGO PHONE R
・Output Master：
L 1:DDJ-ERGO MASTER L
R 2:DDJ-ERGO MASTER R
(3) Input Routing
* For those who do not use external input (AUX/MIC), the following setup is not
needed.
・Input Aux
L(Mono) 1:DDJ-ERGO AUX/MI L
R 2:DDJ-ERGO AUX/MI R
(4) Mix Recorder
・Source：Internal
11. Close the TRAKTOR PRO 2, power off the DDJ-ERGO and turn it on again, and
reboot the TRAKTOR PRO 2.
Now, you have completed all the settings.
About trademarks and registered
trademarks
・TRAKTOR is the registered trademark of Native Instruments GmbH.
・Microsoft
®
, Windows Vista
®
, Windows
®
, and Internet Explorer
®
are either registered trademarks
or trademarks of Microsoft Corporation in the United States of America and other countries.
・Apple, Macintosh, Mac OS, Safari, iTunes, and Finder are trademarks of Apple Inc., registered
in the U.S. and other countries.
©2012 PIONEER CORPORATION all rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
<DRH1128-B-EN>
・To operate TRAKTOR PRO 2 using the buttons of DDJ-ERGO, see the separate
“Hardware Diagram for TRAKTOR PRO 2”.
・TRAKTOR PRO 2 is a product of Native Instruments.
In principle, Pioneer is not in the position of answering any inquiries on the
usage of the software itself. For further details, please refer to the manual of
TRAKTOR and other resources.