Planet POE-E101 User manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Introduction
1.1 Packet Contents
Thank you for purchasing PLANET POE-E101 IEEE
802.3af Power over Ethernet Extender, your Power
over Ethernet Extender package shall contains following
contents:
Check the contents of your package for following parts:
Power over Ethernet Extender x 1
User's Manual x 1
If any of these pieces are missing or damaged, please
contact your dealer immediately, if possible, retain the
carton including the original packing material, and use them
against to repack the product in case there is a need to
return it to us for repair.
1.3 TechnicalSpecication
Model POE-E101
Interfaces
LAN IN
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” in Auto MDI/
MDI-X, Auto-negotiation RJ-45 connector
LAN OUT
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” out Auto
MDI/MDI-X, Auto-negotiation RJ-45
connector
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet
PoE Power
Supply Type Mid-Span / Type B
PoE Power
Output 48V DC, 270mA, Max. 13 Watts
Power Pin
Assignment 4/5(+), 7/8(-)
Hardware Specication
Data Rate 10/100Mbps
Switch
Architecture Store-and-Forward
Switch
Throughput 148810pps@64Bytes
Latency 7.840µs
2.2 Ports connection
IN Port
Connect the PoE IN port from following
802.3af PSE device through a CAT-5e/6 UTP
cable:
• PoE injector
• PoE Injector Hub
• PoE Ethernet Switch
• Previous POE-E101
OUT Port
Connect the PoE OUT port to following
802.3af PD device through a CAT-5e/6 UTP
cable:
• PoE IP Camera
• PoE VoIP Phone
• PoE Wireless AP
• PoE Splitter
• Next POE-E101
2.3 LEDdenition:
LED Color Function
PoE IN Green Lights to indicate the port is
providing 48VDC in-line power.
LNK/
ACT Green
Lights to indicate the port is link up.
Blink: indicate that the extender is
actively sending or receiving data
over IN port.
PoE OUT Green Lights to indicate the port is
providing 48VDC in-line power.
Standard
Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 10/100Base-TX Fast
Ethernet
IEEE 802.3af Power over Ethernet PSE /
Mid-Span
IEEE 802.3af Power over Ethernet PD /
Mid-Span
IEEE 802.3x Flow Control
Environment
Operating
Temperature: -10 ~ 60 Degree C
Relative Humidity: 0 ~ 95%
(non-condensing)
Storage
Temperature: -40 ~ 85 Degree C
Relative Humidity: 5 ~ 95%
(non-condensing)
1.2 Key Features
● ComplieswithIEEE 802.3af Power over Ethernet
● Extends the range of PoE an additional 100 meters
(328ft.)
● Forwards both Ethernet data and PoE power to remote
device
● Auto-detect and protect of PoE equipment from being
damaged by incorrect installation
● Multipleunits,daisy-chaininstallationsupport
● Noexternalpowercableinstallationrequired
● Compactsize,Wall-mountabledesign
● Plug-and-Play installation
Maximum
Frame Size 1552Bytes
Flow Control Back pressure for Half-Duplex
IEEE 802.3x Pause Frame for Full-Duplex
LED Indicators
• 1 x PoE IN (Green)
• 1 x LAN Data (Green)
• 1 x PoE OUT (Green)
Protection ESD (Ethernet) : 6KV (TBD)
Surge (EFT for power) : 6KV (TBD)
Dimension
(W x D x H) 94 x 70 x 26 mm
Weight 215g
Power
Requirement
IEEE 802.3af compliant with voltage
within 44V-56V DC
Power
Consumption 2 Watts (system maximum)
Mechanical Metal / Wall Mountable
Cable TIA/EIA-568, Category 5/5e cable
Standards Conformance
Regulation
Compliance FCC Part 15 Class A, CE
2. Hardware Description
2.1 Product Outlook
3. Hardware Installation
This product provides two different running speeds –
10Mbps, 100Mbps in the same device and automatically
distinguishes the speed of incoming connection.
This section describes the hardware features of POE-E101.
Before connecting any network device to the POE-E101,
read this chapter carefully.
3.1 Before Installation
Before your installation, it is recommended to check your
network environment. If there is any far away IEEE 802.3af
devices need to power on, the POE-E101 can provide you a
way to supply power for this Ethernet device conveniently
and easily.
The POE-E101 is installed between the PSE (Power Source
Equipment) and the PD (Powered Device); it is powered
by PSE and forwards the Ethernet data and remaining POE
powertothePD.ThePOE-E101doesn’trequireanexternal
power supply and it can be installed easily just plug and
play; that means the operator does not need to congure
the POE-E101. The POE-E101 injects power to the PDs
without affecting the data transmission performance. It
offers a cost effective and quick solution to extend power
and data an additional 100m.
Note
The POE-E101 can be installed with third-party
device if the device complied with IEEE 802.3af
standard.

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2 Connect POE-E101 to the Power Source
Equipment (PSE)
There are 2 RJ-45 ports in the PoE Extender, of which the
“IN” port functions as “PoE (Data and Power) input"
and the ”OUT” port on the other side functions as “PoE
(Data and Power) output”.
Step 1: Connect a standard Cat5e/6 UTP cable from
Power Source Equipment (PSE), such as PoE
Switch, PoE Injector hub and single port PoE
injector, to the “IN” port of POE-E101.
Step 2: The PSE delivers both Ethernet Data and PoE
power over UTP cable to the POE-E101 and the
“PoE IN” LED will be steady on.
Note
1. The POE IN LED turn on steady green means
POE-E101 is being powered successfully with
PoE class 0.
2. If POE IN LED does not turn on, please
check the remote PSE or the cable with a
PC or a network device to see if the cable
is correct. Or with an 802.3af device such as
the target PD to check the power injection is
correct either.
3.4 Multiple PoE Extender Installation
The POE-E101 PoE Extender supports multiple units, daisy-
chain installation. They can be employed in series for even
longer distances based on remote PoE IP Camera or PoE
WirelessAccessPointpowerrequirement.
Step 1: Connect the additional CAT5e/6 cable from the
“OUT” portof therstPOE-101,the otherendof
the UTP cable be used to connect to the “IN” port
of remote / next POE-E101.
Step 2: The “PoE OUT”LEDindicatoroftherstPOE-101
will be steady to shows it is providing power to
next PoE Extender.
Step 3: The “PoE IN” LED on the next POE-101 will
steady on.
Step 4: Connect the additional CAT5e/6 cable to the
remote PoE powered device to the “OUT” port of
next or third POE-E101.
3.3 Connect POE-E101 to the Powered Device
(PD)
Step 3: Connect the additional CAT5e/6 cable that will be
used to connect to the remote Powered Device
(PD) to the “OUT” port of POE-E101.
Step 4: The “OUT" port is also the power injectors which
transmit DC Voltage to the Cat5e/6 cable and
transfer data and power simultaneously between
the PSE and PD.
Step 5: Once POE-E101 detects the existence of an IEEE
802.3af device, the “PoE OUT” LED indicator will
be steady, ON to shows it is providing power.
PoE IP Camera PoE Injector
POE-E101
PoE Extender
PoE PoE
AC
+Power
Data
Data
+Power
Data
Power
100M100M
200M
DC
PoE
100Base-TX UTP with PoE
100Base-TX UTP
DC Power Line (DC)
Power Line (AC)
AC
Note
1. If the connected device is not fully
complying with IEEE 802.3af standard or
in-line power device, the PoE OUT LED
indicator of POE-E101 will not be steady on.
2. According to IEEE 802.3af standard, the
POE-E101 will not inject power to the cable
if not connecting to a standard IEEE 802.3af
device.
POE-E101
PoE Extender
PoE Ethernet Switch/
Injector Hub
PoE
PoE
PoE
PoE
PoE
PoE
PoE PoE
PoE
100M100M100M
100M
100M100M100M
PoE Access Point
PoE IP Camera
non-PoE IP Camera
PoE Splitter
100M100M
DC
Power Output
300m 200m 100m 0m400m
AC
PoE
100Base-TX UTP with PoE
100Base-TX UTP
DC Power Line (DC)
Power Line (AC)
AC
(11W)(9W) (13W) (15W)
POE-E101
PoE Extender
POE-E101
PoE Extender
POE-E101
PoE Extender
POE-E101POE-E101
Note
1. Per POE-E101 will take 2 watts maximum
for the system itself, please check the total
power consumption of your 802.3af PD
and the POE-E101 before you make the
daisy-chain connection. If the overall power
consumption is overloaded, the local PSE
could shutdown the whole power system.
2. Per POE-E101 cable segment is limited in
100 meters Cat5e/6 UTP wire from its IN/
OUT port to the other data end, use of any
other non standard cable or over distance
could results in unstable connection.
3.5 Optional - DIN-Rail mounting
There are two DIN-Rail holes on the left side of the POE-
E101 that allows the converter can be easily installed with
DIN-Rail mounting. The PLANET optional DIN-Rail mounting
Kit – RKE-DIN can be order separately. When need to
replace the wall mount application with DIN-Rail application
on the POE-E101, please refer to following gures to screw
the DIN-Rail on the converter. To hang the POE-E101, follow
the below steps:
Step 1: screw the DIN-Rail on the POE-E101.
Step 2: Lightly press the button of DIN-Rail into the track.
1
2
Step 3: Check the DIN-Rail is tightly on the track.
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.