Planet IPOE-E174 User manual

Industrial 1-Port 802.3bt PoE++ to 4-Port 802.3af/at
Gigabit PoE Extender
IPOE-E174
User’s Manual

Table of Contents
1. Packet Contents ................................................................................... 3
2. Hardware Introduction .......................................................................... 4
2.1 Front Panel ................................................................................... 4
2.2 LED Indicators............................................................................... 5
2.3 Grounding the Device..................................................................... 6
3. Installation .......................................................................................... 7
3.1 DIN-rail Mounting Installation ......................................................... 7
3.2 Wall-mount Plate Mounting ............................................................. 7
3.3 Connecting IPOE-E174 to PSE......................................................... 8
3.4 Connecting IPOE-E174 to PD .......................................................... 9
4. Power over Ethernet Budget................................................................ 11
5. Technical Specications ....................................................................... 12
6. Physical Dimensions ........................................................................... 14

3
1. Packet Contents
Thank you for purchasing PLANET Industrial 1-Port 802.3bt PoE++ to 4-Port
802.3af/at Gigabit PoE Extender, IPOE-E174. In the following sections, the
term “Industrial PoE Extender” means the IPOE-E174.
Open the box of the IPOE-E174 and carefully unpack it. The box should
contain the following items:
Industrial PoE Extender x 1 QR code sheet
RJ45 Dust Cap Wall Mounting Kit
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a need to
return it to us for repair.

4
2. Hardware Introduction
This section describes the functionalities of the Industrial PoE Extender’s
components.
2.1 Front Panel
Figure 2-1 shows the front panel of Industrial PoE Extender.
ACT
LNK
PoE IN
PoE Power Usage
60W40W20W
60W30W 90W
Industrial 4-Port PoE Extender
PoE Input
1
2
3
4
AC T
LNK
PoE-
in-Use
Figure 2-1: IPOE-E174 Front Panel

5
2.2 LED Indicators
System
LED Color Function
30W IN Green Lights to indicate the IPOE-E174 is working in 2-pair
modeandoersupto30-wattpower.
60W IN Green Lights to indicate the IPOE-E174 is working in 4-pair
modeandoersmorethan60-wattpower.
90W+ IN Green Lights to indicate the IPOE-E174 is working in 4-pair
modeandoersmorethan90-wattpower.
PoE Input Port
LED Color Function
LNK/ACT Green
Lights to indicate the port is linked up.
Blinks to indicate that the IPOE-E174 is actively
sending or receiving data over that port.
PoE-in-Use Amber
Lights to indicate the port is obtaining PoE power from
PSE devices.
OFF to indicate the port is not obtaining PoE power
from PSE devices.
PoE Power Usages
LED Color Function
20W Amber
Blinks to indicate the system is providing 10W ~ 20W PoE
power.
Lights to indicate the system is providing 20W ~ 30W PoE
power.
40W Amber
Blinks to indicate the system is providing 30W ~ 40W PoE
power.
Lights to indicate the system is providing 40W ~ 50W PoE
power.
60W Amber
Blinks to indicate the system is providing 50W ~ 60W PoE
power.
Lights to indicate the system is providing 60W+ PoE power.

6
Per PoE Output Ports (Ports 1 to 4)
LED Color Function
LNK/ACT Green
Lights to indicate the port is linked up.
Blinks to indicate that the IPOE-E174 is actively
sending or receiving data over that port.
PoE-in-Use Amber Lights to indicate the port is providing PoE power.
OFF to indicate the connected device is not a PoE PD.
2.3 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
Earth Ground
EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

7
3. Installation
This section describes the functionalities of the Industrial PoE Extender’s
components and guides you to installing it on the DIN rail and wall. Please
read this chapter completely before continuing.
This following pictures show how to install the device. However,
the device in the picture is not the IPOE-E174.
3.1 DIN-rail Mounting Installation
1
2
3.2 Wall-mount Plate Mounting

8
3.3 Connecting IPOE-E174 to PSE
TheIndustrialPoEExtender has ve RJ45 ports of whichoneisthePoE++ In
port connected to the PSE and the other four are PoE+ Out ports connected
to the PDs.
Step 1: Connect a standard Cat5e/6 UTP cable from a remote PSE, such as
PoE switch, to the “PoE++ In” port of the IPOE-E174.
PoE
PSE 802.3bt/Ultra PoE input
ACT
LNK
60W30W 90W
Industrial
PoE Input
Step 2: The PSE delivers both Ethernet Data and PoE power over UTP cable
to the IPOE-E174 and the “PoE IN” LED will be lit steadily.
1. When the LED turns steady green, it means the IPOE-E174 is
being powered successfully with PoE.
2. If the LED is not lit, please check whether the remote PSE
or the cable is connected to a PC or a network device, or
the use of cable is correct or not. If not, check whether the
power injection going to a PD is correct or not.
3. Never connect any non-standard PoE PSE to the IPOE-E174;
it will damage the device permanently.
4. Refer to Chapter 2.2 for more information about LED function.

9
3.4 Connecting IPOE-E174 to PD
Step 1: Connect the additional Cat5e/6 cable from the PoE+ Out of the
IPOE-E174 to a remote PD.
802.3at/802.3af PoE output
PoE
PD
PoE Power Usage
60W40W20W
1
2
Step 2: The PoE+ Out port is also the power injector, which transmits
DC voltage to the Cat5e/6 cable and transfers data and power
simultaneously between the PSE and PD.
Step 3: Once the IPOE-E174 detects the existence of an IEEE 802.3at/af
device, the PoE-in-Use LED indicator will be lit steadily, showing it
is providing power.
ACT
LNK
PoE IN
PoE Power Usage
60W40W20W
60W30W 90W
Industrial 4-Port PoE Extender
PoE Input
1
2
3
4
AC T
LNK
PoE-
in-Use
802.3bt PoE++ (60-95W)
IEEE 802.3at (25W)
IEEE 802.3at (25W)
PoE PTZ IP Camera
Power
Data

10
ACT
LNK
PoE IN
PoE Power Usage
60W40W20W
60W30W 90W
Industrial 4-Port PoE Extender
PoE Input
1
2
3
4
AC T
LNK
PoE-
in-Use
802.3bt PoE++ (60-95W)
Power
Data
IEEE 802.3at (15W)
IEEE 802.3at (15W)
IEEE 802.3at (15W)
IEEE 802.3at (15W)
PoE Dome IP Camera
1. If the connected device is not fully complying with IEEE
802.3af/at standard or in-line power device, the PoE-in-Use
LED indicator of the IPOE-E174 will not be lit steadily.
2. According to IEEE 802.3af/at standard, the IPOE-E174 will not
inject power to the cable if not connecting to a standard IEEE
802.3af/at device.
3. DO NOT connect any PSE to ports 1 to 4 of the IPOE-E174;
it may damage the device permanently.