Planet WNRT-320GS User manual

3G / 802.11n Wireless Portable Router
with 3G HSUPA
WNRT-320GS
Quick Installation Guide

Table of Contents
1. Package Contents ................................................. 3
2. Physical Introduction ............................................. 4
3. Hardware Installation ............................................ 5
4. Web UI Conguration .......................................... 10
5. Further Information ............................................ 12

3
1.Package Contents
Thank you for choosing PLANET WNRT-320GS, the most
convenient wireless portable 3G router. Before installing
the router, please verify the contents inside the package
box.
WNRT-320GS Quick Guide CD-ROM
Power Adapter USB Cable Ethernet Cable Li-ion Battery
Note
If there is any item missed or damaged,
please contact the seller immediately.

4
2.Physical Introduction
Top Panel Description
Power/Battery
Wireless Connection
WPS
3G Connection
WAN/LAN
Front Panel Description
The Switch of Router
and AP Modes
Power Connector
RJ-45 Port
Power Switch
Side Panel Description
WPS Button
Reset Button

5
3.Hardware Installation
Please follow the instructions below to activate the
WNRT-320GS.
Step 1: Remove the cover in the bottom of the
machine. You can choose to insert the SIM
card into the slot for 3G connection, or connect
WNRT-320GS directly with the Cable/xDSL
Modem via UTP cable for Internet service. And
install the attached battery into the slot if you
need. Then replace the cover.
WNRT-320GS
N
N
Laptop
Smart Phone N
3G
Base Station
Internet
3G
3G
OR
Client
N
WNRT-320GS
N
Cable/xDSL
Modem
Phone Jack
RJ-45RJ-11
SSID: default
WAN
001101010

6
Note
1. Please only charge the battery by the
power adapter and USB cable attached in
the package.
2. When the battery is being charged, the
red LED will be lit up. After the battery
is fully charged, the LED will become
green. Please do not recharge the battery
continuously at this moment.
3. The battery should be kept in a cool and
dry place.
Step 2: Make sure the operation mode by the hardware
switch is at Router Mode (default setting).
ON/OFF AP/RT
ON/OFF AP/RT
Step 3: Connect the power adapter with the
WNRT-320GS if necessary. And then turn on it.
ON/OFF AP/RT
ON/OFF AP/RT

7
Step 4: Use your PC equipped wireless adapter to site
survey the wireless signal of WNRT-320GS, and
connect your PC with it wirelessly.
Default SSID: default
Default Wireless Encryption: WPA-PSK / WPA2-PSK
Default Password: 1234567890
Note
1. When the WNRT-320GS is at Router
Mode, the only RJ-45 port will act as a
WAN port. Therefore, the client devices
can only connect with WNRT-320GS wire-
lessly. However, if you need to connect
the WNRT-320GS with your computer by
UTP cable, please switch it to AP Mode
first. And the RJ-45 port will act as a
LAN port to be able to connect with your
computer.

8
Note
2. If you cannot obtain an IP address
automatically from the WNRT-320GS at
Router Mode after clicking the Connect
button on the screen, please follow
the procedures below to congure the
Windows Network Connection.
Step 1.Click “Start” button located at
lower-left corner of the screen.
Step 2.Click “Control Panel”.
Step 3.Click “Network and Sharing
Center”.
Step 4.Click “Change adapter settings”.
Step 5.Right-click “Wireless Network
Connection” or “Local Area
Connection”, and choose
“Properties”.
Step 6.Select “Internet Protocol
Version 4 (TCP/IPv4)” and click
“Properties” button.

9
Note
Step 7.Select “Obtain an IP address a
utomatically” and “Obtain DNS
server address automatically”,
then click “OK”.

10
4.WebUIConguration
Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Step 1: Open the Web browser and enter the default IP
address http://192.168.1.1
The default username and password are both
“admin”. Then click OK button to continue.