Planet FGSW-262 User manual

Trademarks
Copyright © PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information
in this User’s Manual, and reserves the right to make improvements to this
User’s Manual and/or to the products described in this User’s Manual, at any
time without notice.
If you nd information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Revision
PLANET 24-port 10/100Mbps + 2-port Gigabit Ethernet Switch User’s Manual
FOR MODEL: FGSW-2620
REV: 1.0 (March.2004)
Part No.: 2010-000032-000

1
Table of Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 How to Use This Manual 1
1.3 Product Features 2
1.4 Product Specifications 3
Chapter 2 Installation 5
2.1 Product Description 5
2.1.1 Product Overview 5
2.2 Installing a Switch 6
Chapter 3 Switch Operation 9
3.1 Address Table 9
3.2 Learning 9
3.3 Forwarding & Filtering 9
3.4 Store-and-Forward 9
3.5 Auto-Negotiation 10
Chapter 4 Troubleshooting 11
Appendix A 13
A.1 Switch‘s RJ-45 Pin Assignments 13

1
Chapter 1
INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
● 24-port 10/100Mbps + 2-port Gigabit Ethernet Switch x1
● User’s manual x1
● Power cord x1
● Two Rack-Mounting Brackets with Attachment Screws x1
If any of these are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against
to repack the product in case there is a need return to it to us for repairing.
1.2 How to Use This Manual
This FGSW-2620 User’s Manual is structured as follows:
● Section 2, Installation
It explains the functions of FGSW-2620 and how to physically install the FGSW-
2620.
● Section 3, Switch operation
It explains the Switch operation of FGSW-2620.
● Section 4 Troubleshooting
It contains troubleshooting guide of FGSW-2620.
● Appendix A
It contains cable information of FGSW-2620. In the following section, the term
“Switch” means the Switch, i.e. FGSW-2620, term of “switch” can be any third
part Switches.

2
3
1.3 Product Features
● Comply with IEEE802.3, IEEE802.3u 10/100Base-TX, IEEE802.3ab 1000Base-
T Ethernet Standard
● 24 (10/100Mbps), 2 (10/100/1000Mbps) Gigabit Ethernet Switch
● Each Switching Fast Ethernet ports support auto-negotiation-10/20, 100/
200Mbps,supported
● Each Switching Gigabit ports support auto-negotiation- 10/20,100/200Mbps,
1000/2000Mbps supported
● Auto-MDI/MDI-X detection on each RJ-45 port
● Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame
flow control (full-duplex)
● High performance Store and Forward architecture, broadcast storm control,
runt/CRC filtering eliminates erroneous packets to optimize the network band-
width
● Provide 8.8Gbps switch fabric, non-blocking switch architecture
● 8K MAC address table, automatic source address learning and ageing
● 2.5Mbit for packet buffer
● 19-inch rack mount size

2
3
1.4 Product Specications
Model FGSW-2620
Hardware Specification
Ports 24 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports
Gigabit ports 2 10/100/1000Base-T RJ-45 Auto-MDI/MDI-X ports
Switch architecture Store-and-forward
Switch Fabric 8.8Gbps
Throughput (packet
per second) 6.547Mpps
Address Table 8K entries
Share data Buffer 2.5Mbit
Flow Control Back pressure for half duplex, IEEE 802.3x Pause
Frame for full duplex
Dimensions 440 x 120 x 44 mm, 1U height
Weight 2kg
Power Requirement 100~240 VAC, 0.5A, 50-60 Hz
Power Consumption /
Dissipation 30 Watts maximum / 100 BTU/hr maximum
Temperature Operating: 0~50 degree C, Storage -40~70 degree C
Humidity Operating: 10% to 90%, Storage: 5% to 95% (Non-condensing)
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3x (full-duplex flow control)

4
5
This page is intentionally left blank

4
5
Chapter 2
INSTALLATION
This section describes the functionalities of FGSW-2620 components and guides how to
install it on the desktop or shelf. Basic knowledge of net-working is assumed. Please read
this chapter completely before continuing.
2.1 Product Description
The PLANET FGSW-2620 provides 24 10/100Mbps Fast Ethernet ports and 2 10/100/
1000Mbps Gigabit Ethernet ports. The two Gigabit Ethernet ports support 10/100/
1000Mbps as well as half/full mode by auto-negotiation and can be easily connected to
corporate backbones and servers.
The PLANET FGSW-2620 is with 8.8Gbps non-blocking switch fabric; the FGSW-2620
offers wire-speed packet transfer performance without risk of packet loss.
2.1.1 Product Overview
PLANET FGSW-2620 is 24-port 10/100Mbps + 2-port Gigabit Ethernet Switch, with
24 RJ-45 10/100Mbps ports and 2 RJ-45 10/100/1000Mbps TP ports for cost effective
high-performance network connectivity. With its 8.8Gbps non-blocking switch fabric, the
PLANET FSGW-2620 can also provide a local, high bandwidth.
This products also supports store-and-forward forwarding scheme to ensure low latency
and high data integrity, eliminates unnecessary trafc and relieves congestion on critical
network paths. With an intelligent address recognition algorithm, FGSW-2620 could
recognize up to 8K different MAC address and enables ltering and forwarding at full
wire speed.
2.1.2 FGSW-2620 Front Panel
Figure 2-1 shows front panel of FGSW-2620.
Figure 2-1 PLANET FGSW-2620 Front Panel
2.1.3 FGSW-2620 Rear Panel
The rear panel of the Switch indicates an AC inlet power socket , which accepts input
power from 100 to 240VAC, 50-60Hz.
Figure 2-2 shows rear panel of FGSW-2620.
Figure 2-2 PLANET FGSW-2620 Rear Panel

6
7
 Power Notice:
1. The device is a power-required device, it means, it will not
work till it is powered. If your networks should active all
the time, please consider using UPS (Uninterrupted Power
Supply) for your device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppression device may
also help to protect your switch from being damaged by
unregulated surge or current to the Switch or the power
adapter.
2.1.4 LED Indicators
System
PWR This indicator lights green when the Switch is receiving power. Oth-
erwise, it is off.
Per 10/100Mbps ports
LNK/
ACT
This indicator light green when the port is connected to an Ethernet
or Fast Ethernet station, if the indicator is blinking green, it will be
transmitting or receiving data on the network.
100 This LED indicator light orange when a Fast Ethernet station is
connected. It remains OFF, if an Ethernet station is connected.
Per 10/100/1000Mbps ports
LNK/
ACT
This indicator light green when the port is connected to an Ethernet,
Fast and Gigabit Ethernet station, if the indicator is blinking green, it
will be transmitting or receiving data on the network.
1000
This LED indicator light green when a Gigabit Ethernet station is
connected. It remains OFF, if an Ethernet or Fast Ethernet station
is connected.
100
This LED indicator light green when a Fast Ethernet station is con-
nected. It remains OFF, if an Ethernet station or Gigabit Ethernet
station is connected.
2.2 Installing a Switch
This part describes how to install your FGSW-2620 and make connections to the
Switch. Please read the following topics and perform the procedures in the order being

6
7
presented.
To install your Switch on a desktop or shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install a Switch on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch.
Step2: Place the Switch on a desktop or shelf near an AC power source.
Step3: Keep enough ventilation space between the Switch and the surrounding
objects
 Note:
When choosing a location, please keep in mind the environmental
restrictions discussed in Chapter 1, Section 4, Specication.
Step4: Connect your Switch to network devices
A. Connect one end of a standard network cable to the 10/100 or 10/100/
1000Mbps RJ-45 ports on the front of the Switch.
B. Connect the other end of the cable to the network devices such as
printer servers, workstations or routers…etc.
 Note:
Connection to the Switch requires UTP Category 5 network
cabling with RJ-45 tips. For more information, please see the
Cabling Specication in Appendix A.
Step5: Supply power to the Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a standard wall outlet
then power on the Switch.
When the Switch receives power, the Power LED should remain solid Green.
2.2.2 Rack Mounting
To install the Switch in a 19-inch standard rack, follow the instructions described below.
Step1: Place your Switch on a hard flat surface, with the front panel positioned
towards your front side.
Step2: Attach a rack-mount bracket to each side of the Switch with supplied
screws attached to the package. Figure 2-3 shows how to attach brackets
to one side of Switch.

8
9
Figure 2-3 Attaching the brackets to the FGSW-2620
Caution:
You must use the screws supplied with the mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate your warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the switch, use suitable screws to se-
curely attach the brackets to the rack, as shown in Figure 2-4.
Figure 2-4 Mounting the FGSW-2620 in a Rack
Step6: Proceed with the steps 4 and steps 5 of section 2.2.1 Desktop Installation
to connect the network cabling and supply power to your Switch.