Planet GSD-808HP User manual

8-Port 10/100/1000Mbps 802.3at PoE Desktop Switch
GSD-808HP / GSD-808HP2
User’s Manual

Trademarks
Copyright © PLANET Technology Corp. 2012.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from
the power circuit.
Without removing power cable, the device will still consuming power from the
power source. In the view of Saving the Energy and reduce the unnecessary power
consuming, it is strongly suggested to remove the power connection for the device
if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such WEEE
separately.
Revision
PLANET 8-Port 10/100/1000Mbps 802.3at PoE Desktop Switch User's Manual
For Models: GSD-808HP & GSD-808HP2
Revision: 2.1 (JUNE, 2012)
Part No.: 2350-A35130-002

Table of Contents
1. Introduction................................................................................................. 5
1.1 Checklist................................................................................................ 5
1.2 Product Description................................................................................. 5
1.3 Features ................................................................................................ 6
1.4 Specication........................................................................................... 7
2. Hardware Description ................................................................................... 9
2.1 Front Panel ............................................................................................ 9
2.1.1 LED Indicators ............................................................................... 9
2.2 Rear Panel ............................................................................................10
2.3 Desktop Installation ...............................................................................11
2.4 Rack Mounting ......................................................................................12
2.5 Product Application ................................................................................14
2.5.1 Train Station................................................................................. 14
2.5.2 IP Ofce ......................................................................................15
2.6 Power over Ethernet Powered Device ......................................................16
3. Power over Ethernet Overview......................................................................17
4. Troubleshooting...........................................................................................20
Appendix A Networking Connection ..................................................................21
A.1 PoE RJ-45 Port Pin Assignments..............................................................21
A.2 Switch's Data RJ-45 Pin Assignments - 1000Mbps, 1000Base-T .................21
A.3 10/100Mbps, 10/100Base-TX ..................................................................22

5
1. Introduction
1.1 Checklist
Check the contents of your package for following parts:
GSD-808HP or GSD-808HP2 x 1l
User's Manual x 1l
19” Rack Mount Accessory Kit x 1l
Rubber Feet x 4l
Power Cord x 1l
If any of these pieces are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original packing material,
and use them against to repack the product in case there is a need to return it to
us for repair.
1.2 Product Description
To fulll the demand of High Power PoE for network applications with Gigabit speed
transmission, the PLANET 802.3at PoE Gigabit Ethernet Switch family -GSD-808HP
and GSD-808HP2 is an ideal solution. Each 10/100/1000Mbps port of GSD-808HP
and GSD-808HP2 features IEEE 802.3af and High Power IEEE 802.3at Power
over Ethernet (PoE) that combines up to 130 Watts / 240 Watts power output
and data per port over one Cat.5E / 6 Ethernet cable, with totally 130 Watts
(GSD-808HP) / 240 Watts (GSD-808HP2) PoE budget on whole system, it is
designed specically to satisfy the growing demand of higher power consuming
network PD (powered devices) such as PTZ (Pan, Tilt & Zoom) / Speed Dome
network cameras, multi- channel (802.11a / b / g / n) wireless LAN access
points and other network devices by providing double PoE power than conventional
802.3af PoE currently.
The 8 Gigabit High Power PoE ports in the GSD-808HP / GSD-808HP2 support
both 802.3af and 802.3at PoE standards and allows users exibly connect standard
and high powered devices simultaneously, the GSD-808HP offering 130 Watts
PoE budget, eight 15.4 Watts IEEE 802.3af devices or four 30 Watts IEEE 802.3at
devices can be easily installed without the power-socket limitation. The GSD-
808HP2 offering 240 Watts PoE budget, eight 15.4 Watts IEEE 802.3af devices
or eight 30 Watts IEEE 802.3at devices can be easily installed without the power-
socket limitation.
To facilitate power management, the GSD-808HP / GSD-808HP2 is implemented
powerful PoE management feature, the over temperature protection to prevent
power budget overloading. The four orange LEDs hardware designed that located

6
on right side of GSD-808HP / GSD-808HP2 front panel, it call “PoE Power Usage”
and its meaning of lower to upper LED is 25%, 50%, 75% and 95%. With these
LED indications, you can monitor current PoE power used status of GSD-808HP /
GSD-808HP2 easily and efciently.
Providing data transfer and High Power PoE in one unit, the GSD-808HP / GSD-
808HP2 shall reduce the need of extension cables and dedicated electrical outlets
on the wall, ceiling or any unreachable place. It helps to lower the installation
costs and simplify the installation effort. Besides, the rst important key feature
is energy saving. With more efcient switching power supply, the efciency of the
GSD-808HP / GSD-808HP2 would be much better than eight linear power adapters
in the long run. Furthermore, it is the ideal device for bridging among Fast Ethernet
and Gigabit Ethernet workgroups and networks. With Gigabit throughput and eight
IEEE 802.3af / 802.3at PoE interfaces supported, the GSD-808HP / GSD-808HP2
is ideal for small business and workgroups to efciently deploy the High Power PoE
network for the wireless access points, IP-based surveillance camera or IP phones
in any places.
The GSD-808HP / GSD-808HP2 has 8K MAC address table, features high
performance switch architecture capable of providing the non-blocking 16Gbps
switch fabric and wire-speed throughput as high as 11.9Mpps, which greatly
simplies the tasks of upgrading the LAN for catering to increasing bandwidth
demands. Besides, the 802.3x Full-Duplex ow control function of the GSD-808HP
/ GSD-808HP2 enables PD devices and servers directly connect to the Switch for
wire-speed packet transfer performance without risk of packet loss.
All RJ-45 copper interfaces in the GSD-808HP / GSD-808HP2 support
10/100/1000Mbps Auto-Negotiation for optimal speed detection through RJ-45
Category 6, 5 or 5e cables. It also supports standard Auto-MDI/MDI-X that can
detect the type of connection to any Ethernet device without requiring special
straight or crossover cables.
1.3 Features
RJ-45 Interface
8-Port 10/100/1000Mbps Gigabit Ethernet ports
8-Port supports 52V DC power to PoE Powered Device
PoE
Complies with IEEE 802.3af / 802.3at Power over Ethernet End-Span PSE
Up to 8 IEEE 802.3af / 802.3at devices powered
PoE Power up to 30 Watts for each 802.3at PoE port

7
GSD-808HP provide 130 Watts PoE budget, GSD-808HP2 provide 240 Watts
PoE Budget
Over Temperature Protection support
Auto detect powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
Switching
Hardware based 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDI-X
Flow control for Full Duplex operation and back pressure for Half Duplex oper-
ation
Integrates address look-up engine, supporting 8K absolute MAC addresses
9K Jumbo Frame supports at all speed (10/100/1000Mbps)
Automatic address learning and address aging
Hardware
13-inch desktop size, 19” rack mountable; 1U height
LED indicators for system Power, Fan Failure, per port speed, Link / Act
LED indicators for per port PoE In-Use and PoE Power Usage (25%, 50%,
75% and 95%)
 1 FAN to provide stable and efcient power performance
Ethernet Link Energy-Saving technology
- Link down power saving
- Intelligent scales power based on cable length
1.4 Specication
Model GSD-808HP GSD-808HP2
Hardware Specication
Hardware Version 2 1
Network Connector 8-Port RJ-45 for 10/100/1000Base-T
PoE Inject Port 8-Port with 802.3af / 802.3at PoE injector function
LED Display
System: Power x 1 (Green), FAN Alert x 1
(Orange), PoE Power Usage x 4 (Orange)
Per Port: PoE In-use (Orange), Speed (Green),
LNK/ACT (Green)

8
Switch Architecture Store and Forward switch architecture
MAC Address Table 8K MAC address table with Auto learning function
Switch Fabric 16Gbps
Switch Throughput 11.9Mpps
Jumbo Packet Size 9K Bytes
Flow Control Back pressure for Half-Duplex.
IEEE 802.3x Pause Frame for Full-Duplex
Power Requirement AC 100~240V, 50/60Hz,
1.5A
AC 100~240V, 50/60Hz,
1.25A
Power Consumption 150 Watts / 511BTU 250 Watts / 853BTU
Dimension (W x D x H) 330 x 155 x 43.5mm 330 x 155 x 43.5mm
Weight 1.56kg 1.66kg
Power over Ethernet
PoE Standard IEEE 802.3af / 802.3at Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output
Per Port 52V DC, 275mA. Max. 15.4 Watts
(IEEE 802.3af)
Per Port 52V DC, 535mA. Max. 30 Watts
(IEEE 802.3at)
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget 130 Watts 240 Watts
Max. number of Class 2 PD 8 8
Max. number of Class 3 PD 8 8
Max. number of Class 4 PD 4 8
Standard Conformance
EMI Safety FCC Class A, CE
Operating Environment 0 ~ 50 Degree C
Storage Environment -40 ~ 70 Degree C
Operating Humidity 5 ~ 95%, Relative Humidity, non-condensing
Storage Humidity 5 ~ 95%, Relative Humidity, non-condensing
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Power over Ethernet
High Power over Ethernet

9
2. Hardware Description
2.1 Front Panel
The Front Panel of the GSD-808HP / GSD-808HP2 PoE Ethernet Switch consists of
8x Auto-Sensing 10/100/1000Mbps Ethernet RJ-45 Ports. The LED Indicators are
also located on the front panel of the GSD-808HP / GSD-808HP2.
Figure 2-1: GSD-808HP Switch Front Panel
PoE I n Use
1PWR
FAN Alert
1000
95%
PoE Power
Usage
75%
50%
25%
2345678
GSD-808HP2
8-Port 10/100/1000Mbps 802.3at PoE Switch 2
1
4
3
6
5
8
7
ACT
LNK
Full 30Watts
Figure 2-2: GSD-808HP2 Switch Front Panel
2.1.1 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
FAN Alert Orange Lights to indicate that the FAN failure.
Per 10/100/1000Mbps Port
LED Color Function
PoE In-use Orange
Lights to indicate the port is providing 52V DC in-line
power. (1-8 ports), blinks slowly to indicate the port
has no sufcient PoE power to feeding.
Speed Green
Lit: indicate the Switch is successfully connecting to
the network at 1000Mbps.
Off: indicate that the Switch is successfully connecting
to the network at 10Mbps or 100Mbps.
LNK/ACT Green
Lit: indicate the link through that port is successfully
established.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.

10
Per PoE Power Usage (Unit : %) (Lower LED to upper LED)
LED Color Function
25% Orange Lights to indicate the system has 25% PoE power usage.
50% Orange Lights to indicate the system has 50% PoE power usage.
75% Orange Lights to indicate the system has 75% PoE power usage.
95% Orange Lights and blinks to indicate the system has 95% PoE power
usage.
2.2 Rear Panel
The rear panel of the GSD-808HP / GSD-808HP2 indicates an AC inlet power
socket, which accepts input power from 100 to 240V AC, 50-60Hz, 1.5A (GSD-
808HP) / 1.25A (GSD-808HP2) and has a fan hole on the rear panel.
100~240V AC
50/60Hz
ON
OFF
POWER
Figure 2-3: GSD-808HP / GSD-808HP2 Switch Rear Panel
Power
Notice
The device is a power-required device, it means, it will not work till
it is powered. If your networks should active all the time, please
consider using UPS (Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or network downtime.
In some area, installing a surge suppression device may also help
to protect your GSD-808HP / GSD-808HP2 from being damaged by
unregulated surge or current to the GSD-808HP / GSD-808HP2 or
the power adapter.
Before start up
Before your installation, please refer to the followings for your cabling:
10/100/1000Base-T
All 10/100/1000Base-T ports come with Auto-Negotiation capability. They
automatically support 1000Base-T, 100Base-TX and 10Base-T networks. Users only
need to plug a working network device into one of the 10/100/1000Base-T ports,
and then turn on the GSD-808HP / GSD-808HP2. The port will automatically runs
in 10Mbps, 20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the
negotiation with the connected device.