Planet GS-4210 SERIES User manual

L2/L4 Managed Gigabit Ethernet Switch
GS-4210 Series
Quick Installation Guide

Table of Contents
1. Introduction ............................................................................................... 3
2. Package Contents ....................................................................................... 4
3. Requirements ............................................................................................. 5
4. Starting Web Management .......................................................................... 6
4.1 Logging in to the Managed Switch ........................................................ 6
 4.2 SavingCongurationviatheWeb ......................................................... 8
5. Terminal Setup ........................................................................................... 9
5.1 Logging on to Console ........................................................................10
 5.2 ConguringIPAddress........................................................................10
 5.3 SavingtheCongurationviatheConsole..............................................12
6. RecoveringBacktoDefaultConguration.....................................................13
7. Customer Support .....................................................................................15

3
1. Introduction
Thank you for purchasing PLANET L2/L4 Managed Gigabit Ethernet Switch. The
followingistheGS-4210series:
GS-4210-8P2S 8-Port10/100/1000T802.3atPoE+2-Port100/1000XSFP
Managed Switch (120W)
GS-4210-8P2T2S 8-Port10/100/1000T802.3atPoE+2-Port10/100/1000T
+2-Port100/1000XSFPManagedSwitch(240W)
GS-4210-16P4C 16-Port10/100/1000T802.3atPoE+4-PortGigabitTP/SFP
Combo Managed Switch (220W)
GS-4210-24P4C 24-Port10/100/1000T802.3atPoE+4-PortGigabitTP/SFP
Combo Managed Switch (220W)
GS-4210-24PL4C 24-Port10/100/1000T802.3atPoE+4-PortGigabitTP/SFP
Combo Managed Switch (440W)
GS-4210-48T4S 48-Port10/100/1000T+4-Port100/1000XSFPManaged
GigabitSwitch
GS-4210-48P4S 48-Port10/100/1000T802.3atPoE+4-Port100/1000X
SFPManagedSwitch(400W)
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.

4
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
2. Package Contents
Model Series GS-4210-
ModelName
Packaged Items
8P2S 8P2T2S 16P4C 24P4C/
24PL4C
48T4S/
48P4S
The Managed Switch     
QuickInstallationGuide     
RS232 to RJ45 Console
Cable - 
-
RubberFeet     
TwoRack-mountingBrackets
withAttachmentScrews     
Power Cord     
SFPDustCaps 2 2 4 4 4
If any item is found missing or damaged, please contact your local reseller for
replacement.

5
3. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection (Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
The above Workstations have been installed with terminal emulator, such as
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
Serial cable--OneendisattachedtotheRS-232serialport,whiletheother
end to the console port of the Managed Switch.
zEthernet Port Connection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
and then try it again.

6
4. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set to the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 4-1: IP Management Diagram
4.1 Logging in to the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100 to access the Web interface.
2. When the following dialog box appears, please enter the default user name and
password “admin”.TheloginscreeninFigure4-2appears.
DefaultIPAddress:192.168.0.100
DefaultUsername:admin
DefaultPassword:admin
Figure 4-2: Login Screen

7
Note
Thefollowing webscreenbased onGS-4210-8P2Swill be thesame
asthatofGS-4210series.
3.Afterenteringthepassword,themainscreenappearsasFigure4-3shows.
Figure 4-3: Web Main Screen of Managed Switch
The Switch Menu on the top of the Web page lets you access all the commands
and statistics the Managed Switch provides. The Switch Menu always contains one
or more buttons, such as “System”, “Switching”, “QoS”, “Security”, “PoE”
and “Maintenance”.
Figure 4-4: Switch Menu

8
Figure 4-5: Switch Menu
Now, you can use the Web management interface to continue the Switch
management.
Please refer to the user’s manual for more.
4.2 SavingCongurationviatheWeb
To save all applied changes and set the current conguration as a startup
conguration on the Web user interface, the startup-conguration le will be
loaded automatically across a system reboot.
1. Click the Save icon on the top Switch Menu bar.
Figure 4-6: Save Cong -- Hot key
2. Press the “Apply” button to save running conguration to start up congura-
tion.
Figure 4-7: Save Cong -- Maintenance

9
5. Terminal Setup
The GS-4210-8P2T2S, GS-4210-16P4C, GS-4210-24P4C and GS-4210-24PL4C
are equipped with a console interface for local switch setup and maintenance. To
congure the system, connect a serial cable to a COM port on a PC or notebook
computer and to the RJ45 type of the console port of the Managed Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 5-1: Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2. When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:115200
zDatabits:8
zParity:None
zStopbits:1
zFlowcontrol:None
Figure 5-2 COM Port Conguration
Note
Console interface is not available for the GS-4210-8P2S and
GS-4210-48P4S.

10
5.1 Logging on to Console
Once the terminal is connected to the device, power on the Managed Switch and
the terminal will display “running testing procedures”. Then, the following message
asks to log in user name and password. The factory default user name and
passwordareshownasfollows,andtheloginscreeninFigure5-3appears.
Username:admin
Password:admin
Figure 5-3: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
description of the commands, please refer to the following chapters.
Note
1.For security reason, please change and memorize the new pass-
word after this first setup.
2.Only accept command in lowercase letter under console interface.
5.2 ConguringIPAddress
TheManagedSwitchisshippedwithdefaultIPaddressasfollows:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0