Planet IFGS-1822TF User manual

Industrial 16-Port 10/100TX + 2-Port Gigabit TP/SFP
Combo Ethernet Switch
IFGS-1822TF
User’s Manual

Trademarks
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representation,
either implied or expressed, with respect to the quality, performance,
merchantability, or tness for a particular purpose.
PLANET has made every eort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and
does not represent a commitment on the part of PLANET. PLANET assumes no
responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in
this User’s Manual, and reserves the right to make improvements to this User’s
Manual and/or to the products described in this User’s Manual, at any time
without notice.
If you nd information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

ISEDC Statement
CAN ICES-003(A) / NMB-003(A)
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisee aux deux
conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi,
meme si le brouillage est susceptible d'en compromettre le fonctionnement.
CE Mark Warning
This device is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
WEEE Warning
To avoid the potential eects on the environment and human health
as a result of the presence of hazardous substances in electrical and
electronic equipment, end users of electrical and electronic equipment
should understand the meaning of the crossed-out wheeled bin
symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Revision
PLANET Industrial 16-Port 10/100TX + 2-Port Gigabit TP/SFP Combo Ethernet
Switch User's Manual
Model: IFGS-1822TF
Revision: 2.0 (Oct. 2022)
Part No.: 2360-AH7040-000

Table of Contents
1. Package Contents................................................................................. 5
2. Product Specications ........................................................................... 6
3. Hardware Introduction .......................................................................... 8
3.1 Switch Front Panel......................................................................... 8
3.2 LED Denition ............................................................................... 9
3.3 Switch Upper Panel.......................................................................10
3.4 Wiring the Power Inputs................................................................10
3.5 Wiring the Fault Alarm Contact ......................................................12
4. Installation .........................................................................................13
4.1 DIN-rail Mounting Installation ........................................................13
4.2 Wall-mount Plate Mounting ............................................................13
4.3 Side Wall-mount Plate Mounting.....................................................14
4.4 Grounding the Device....................................................................14
5. Customer Support ...............................................................................15

5
1. Package Contents
Thank you for purchasing PLANET Industrial Multi-port 10/100TX Fast
Ethernet Switch, IFGS-1822TF. In the following sections, the term “Industrial
Ethernet Switch” means the IFGS-1822TF.
Open the box of the Industrial Ethernet Switch and carefully unpack it. The
box should contain the following items:
Industrial Ethernet Switch x 1 Quick Sheet x 1
Let’s get started with your PLANET product
IFGS-1822TF
EN Please scan the QR code to browse our online User’s Manual or Quick
Installation Guide and follow the instructions to complete the setup.
Users Manual
DE
Bitte scannen Sie den QR- Code sie werden per Browser zur
Bedienungsanleitung oder Schnellanleitung weiter geleitet. Folgen Sie den
Anweisungen um die Installation abzuschließen.
FR
Veuillez scanner le code QR pour obtenir notre Notice d’Utilisation en
ligne ou notre Guide d’Installation Rapide et suivez les instructions pour
compléter la conguration
ES
Escanee el código QR para encontrar el Manual del Usuario en línea o
la Guía de Instalación Rápida y siga las instrucciones para completar la
conguración.
IT Scansiona il codice QR per consultare online il Manuale utente o la Guida di
installazione rapida e segui le istruzioni per completare la congurazione.
PT Por favor, escaneie o QR code para navegar no Manual do Usuário ou Guia
de Instalação Rápida. Siga as instruções para completar a conguração.
PL
Zeskanuj kod QR, aby otworzyć naszą internetową instrukcję obsługi
lub instrukcję szybkiej instalacji. Postępuj zgodnie z instrukcjami, aby
zakończyć poprawną kongurację.
RU
One word modify: Отсканируйте QR-код, чтобы просмотреть наше
онлайн-руководство пользователя или руководство по быстрой
настройке, и следуйте инструкциям для завершения настройки
RO Te rugam sa scanezi codul QR, pentru a descarca User’s Manual sau Quick
Installation Guide si a urmari instructiunile necesare in nalizarea instalarii
AR
Need more help?
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq
Technical Support: [email protected]
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Part No. 2360-AH7040-000
DIN-rail Kit Wall-mount Kit
RJ45 Dust Cap x 18 SFP Dust Cap x 2
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a need to
return it to us for repair.

6
2.ProductSpecications
Product IFGS-1822TF
Hardware Specications
Fast Ethernet Copper Ports 16 10/100BASE-TX RJ45 auto-MDI/MDI-X ports
Gigabit Ethernet Copper
Ports
Two 10/100/1000BASE-T RJ45 auto-MDI/MDI-X
ports
(shared with Port 17 and Port 18)
SFP Slots Two 1000BASE-SX/LX/BX SFP interfaces
(shared with Port 17 and Port 18)
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin
5/6 for Power 2
Alarm One relay output for power failure.
Alarm relay current carry ability: 1A @ 24V DC
Dimensions (W x D x H) 66 x 107 x 152 mm
Weight 870g
Power Requirements Dual 12~48V DC, 24V AC
Power Consumption Max. 6.3 watts/21.4BTU (Ethernet full loading)
ESD Protection 6KV DC
Switching Specications
Switch Architecture Store-and-Forward
Switch Fabric 7.2Gbps (non-blocking)
Throughput
(packet per second) 5.36Mpps@ 64 bytes
Address Table 16K entries, automatic source address learning
and aging
Shared Data Buer 4Mbits
Flow Control IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex

7
Standards Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Standards Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000T
IEEE 802.3z Gigabit SX/LX
IEEE 802.3x ow control and back pressure
IEEE 802.1p Class of Service
IEEE 802.3az Energy Ecient Ethernet (EEE)
Environment
Operating Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)

8
3. Hardware Introduction
3.1 Switch Front Panel
The front panel of the Industrial Ethernet Switch consists of Ethernet
interfaces and LED indicators
 Front View
挖孔
P1 P2 Alarm
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
1000X
1000T
IFGS-1822TF
ACT
LNK
ACTLNK
100
17
17
18
18
Figure 1: IFGS-1822TF Front View

9
3.2 LEDDenition
System
LED Color Function
P1 Green Lights to indicate power input 1 has power.
P2 Green Lights to indicate power input 2 has power.
Alarm Red Lights to indicate either power 1 or power 2 has no power.
Per 10/100BASE-TX Port
LED Color Function
LNK/
ACT Green
Lights to indicate the link through that port is successfully
established.
Blinking to indicate that the switch is actively sending or
receiving data over that port.
O to indicate that the port is linked down.
100
Speed Amber
Lights to indicate that the port is operating at 100Mbps.
O to indicate that the port is operating at 10Mbps.
O to indicate that the port is linked down.
Per Gigabit RJ45/SFP Combo Interface
LED Color Function
ACT Green
Lights to indicate the link through that port is successfully
established.
Blinking to indicate that the switch is actively sending or
receiving data over that port.
O to indicate that the port is linked down.
LNK Amber
Lights to indicate the link through that port is successfully
established.
Blinks to indicate the port is linked with the network device
that supports EEE function.
O to indicate that the port is linked down.

10
3.3 Switch Upper Panel
The upper panel of the Industrial Ethernet Switch consists of one terminal
block connector within two power input and one relay ouput.
V1+ V1- V2+ V2-
PWR1 PWR2Alarm
DC Input: 12-48V , 2A max.
AC Input: 24V
, 1A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Figure 2: IFGS-1822TF Top View
3.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial Ethernet
Switch is used for two redundant power inputs. Please follow the steps below
to insert the power wire.
When performing any of the procedures like inserting the wires
or tightening the wire-clamp screws, make sure the power is
OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into contacts 1 and 2 for
POWER 1, or contacts 5 and 6 for POWER 2.
V1+ V1- V2+ V2-
PWR1 PWR2Alarm
DC Input: 12-48V , 2A max.
AC Input: 24V
, 1A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6

11
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
Power 1 Alarm Power 2
+-+-
1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
2. The power input range is 12V ~ 48V DC and supports 24V
AC.
3. Use one power input when using 24V AC.

12
3.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as
the picture shows below. Inserting the wires, the Industrial Ethernet Switch
will detect the fault status of the power failure and then forms an open circuit.
The following illustration shows an application example for wiring the fault
alarm contacts.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V DC,1A.

13
4. Installation
This section describes the functionalities of the Industrial Ethernet Switch’s
components and guides you to installing it on the DIN rail and wall. Please
read this chapter completely before continuing.
This following pictures show how to install the device. However,
the device in the picture is not IFGS-1822TF.
4.1 DIN-rail Mounting Installation
1
2
4.2 Wall-mount Plate Mounting

14
4.3 Side Wall-mount Plate Mounting
4.4 Grounding the Device
User MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device. EMD (Lightning) DAMAGE IS
NOT CONVERED UNDER WARRANTY.
V1+ V1- V2+ V2-
PWR1 PWR2Alarm
DC Input: 12-48V , 2A max.
AC Input: 24V
, 1A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Earth Ground

15
5. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource on PLANET web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.