Planet ISW-511 Series User manual

4-Port 10/100Mbps +1/2 100FX Fiber Port
Industrial Fast Ethernet Switch
ISW-511 / ISW-621 Series
ISW-511T / ISW-621T Series
User's Manual

Trademarks
Copyright © PLANET Technology Corp. 2015
Contents are subject to revision without prior notice
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or tness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.

FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances
in electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 4-Port 10/100Mbps +1/2 100FX Industrial Fast Ethernet Switch
User’s Manual
For Models: ISW-511 / ISW-621 / ISW-511T / ISW-621T Series
Revision: 1.4 (April, 2015)
Part No: EM-ISW-511_621_v1.4 (2350-AH0150-003)

Table of Contents
1. Introduction .............................................................................. 6
1.1 Package Contents ................................................................ 6
1.2 How to Use This Manual....................................................... 6
1.3 Product Features ................................................................. 7
1.4 Product Specications .......................................................... 8
2. Installation ..............................................................................14
2.1 Product Description.............................................................14
2.1.1 Switch Front Panel ....................................................15
2.1.2 LED Indicators ..........................................................17
2.1.3 Switch Upper Panel ...................................................17
2.1.4 Wiring the Power Inputs ............................................18
2.1.5 Wiring the Fault Alarm Contact...................................19
2.2 Mounting Installation ..........................................................20
2.2.1 Install DIN-Rail Mounting ...........................................20
2.2.2 Wall Mount Plate Mounting .........................................22
3. Applications .............................................................................23

4. Switch Operation......................................................................27
4.1 Address Table.....................................................................27
4.2 Learning ............................................................................27
4.3 Forwarding & Filtering .........................................................27
4.4 Store-and-Forward..............................................................28
4.5 Auto-negotiation.................................................................28
5. Troubleshooting ........................................................................29
APPENDIX A: Networking Connection...............................................30
A.1 Switch’s RJ45 Pin Assignments ............................................30
A.2 RJ45 cable Pin Assignments ................................................31

6
1. Introduction
1.1 Package Contents
Check the contents of your package for the following parts:
zIndustrial Fast Ethernet Switch x 1
zUser's Manual x 1
zDIN Rail Kit x 1
zWall Mount Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately. If possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair
1.2 How to Use This Manual
This Industrial Fast Ethernet Switch User Manual is structured as
follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Industrial Fast Ethernet Switch.
Chapter 3 Application
The chapter explains the Industrial Fast Ethernet Switch application.
Chapter 4 Switch operation
The chapter explains the Industrial Fast Ethernet Switch transmit
operation.
Chapter 5 Troubleshooting
The chapter explains the troubleshooting of the Industrial Fast Ethernet
Switch.
Appendix A
This chapter contains cable information of the Industrial Fast Ethernet
Switch.

7
1.3 Product Features
Physical Port
Model Name Ports Fiber Optical Interface
Copper Optical Mode Distance
ISW-511
4 x
10/100BASE-TX
1 x
100BASE-FX
Multi-mode 2km
ISW-511T
ISW-511S15 Single-
mode 15km
ISW-511TS15
ISW-621
2 x
100BASE-FX
Multi-mode 2km
ISW-621T
ISW-621S15 Single-
mode 15km
ISW-621TS15
ISW-621TF
Multi /
Single
Mode
depending
on SFP
Module
Layer 2 Features
Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX
Supports auto-negotiation and 10/100Mbps half / full duplex mode
for each copper port
High performance store and forward architecture, broadcast storm
control, runt/CRC ltering eliminates erroneous packets to optimize
the network bandwidth
Prevents packet loss with back pressure (half-duplex) and IEEE
802.3x pause frame ow control (full-duplex)
Backplane (switching fabric):
ISW-511 / ISW-511T Series: 1Gbps
ISW-621 / ISW-621T Series: 1.2Gbps
Integrated address look-up engine, supporting 2K absolute MAC
addresses
1Mbit on-chip frame buffer on ISW-511 / ISW-621 Series and ISW-
511T / ISW621T Series
Automatic address learning and address aging
CSMA/CD Protocol

8
Industrial Case / Installation
IP30 metal case
DIN rail and wall mount design
12 to 48V DC, redundant power with polarity reverse protect function
and connective removable terminal block for master and slave power
-10 to 60 degrees C operating temperature on ISW-511 / ISW-
511S15 / ISW-621 / ISW-621S15
-40 to 75 degrees C operating temperature on ISW-511T / ISW-
511TS15 / ISW-621T / ISW-621TS15 / ISW-621TF
1.4 Product Specications
Model ISW-511 ISW-511S15
Hardware Specications
Copper
Ports 4 x 10/100BASE-TX, auto-negotiation, auto-MDI/
MDI-X
Cable
10BASE-T : 2-pair UTP Cat. 3, 4, 5 cable (100
meters, max.)
100BASE-TX : 2-pair UTP Cat. 5, 5e, 6 cable
(100 meters, max.)
Fiber Optical
Port 1 x 100BASE-FX
Cable 50/125μm ber
62.5/125μm ber 9/125μm ber
Mode multi-mode single-mode
Distance 2km 15km
Dimensions (W x D x H) 135 x 97 x 32mm
Weight 436g
Power Requirements 12~48V DC, Redundant power with polarity
reverse protection function
Power Consumption /
Dissipation 9.1 watts / 31BTU
Installation DIN rail kit and wall mount ear

9
Switch Specications
Switch Processing Scheme Store-and-Forward
Address Table 2K entries
Buffer 1Mbit
Flow Control Back pressure for half duplex,
IEEE 802.3x pause frame for full duplex
Switch Fabric 1Gbps
Throughput
(Packet Per Second) 0.74Mpps @ 64Bytes
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet, 10BASE-T
IEEE 802.3u Fast Ethernet, 100BASE-TX,
100BASE-FX
IEEE 802.3x full-duplex ow control
Stability testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Temperature Operating: -10~60 degrees C
Storage: -40~85 degrees C
Humidity Operating Operating: 5% to 90%, Storage: 5% to 90%
(non-condensing)
Regulation Compliance FCC Part 15 Class A, CE
Model ISW-511T ISW-511TS15
Hardware Specications
Copper
Ports 4 x 10/100BASE-TX, auto-negotiation,
auto-MDI/MDI-X
Cable
10BASE-T : 2-pair UTP Cat. 3, 4, 5 cable
(100 meters, max.)
100BASE-TX : 2-pair UTP Cat. 5, 5e, 6 cable
(100 meters, max.)

10
Fiber Optical
Port 1 x 100BASE-FX
Cable 50/125μm ber
62.5/125μm ber 9/125μm ber
Mode multi-mode single-mode
Distance 2km 15km
Dimensions (W x D x H) 135 x 97 x 32mm
Weight 436g
Power Requirements 12~48V DC, Redundant power with polarity
reverse protection function
Power Consumption /
Dissipation 13.7 watts / 46BTU
Installation DIN rail kit and wall mount ear
Switch Specications
Switch Processing Scheme Store-and-Forward
Address Table 2K entries
Buffer 1Mbit
Flow Control Back pressure for half duplex,
IEEE 802.3x pause frame for full duplex
Switch Fabric 1Gbps
Throughput
(Packet Per Second) 0.74Mpps @ 64Bytes
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet, 10BASE-T
IEEE 802.3u Fast Ethernet, 100BASE-TX,
100BASE-FX
IEEE 802.3x full-duplex ow control
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)

11
Temperature Operating: -40~75 degrees C
Storage: -40~85 degrees C
Humidity Operating: 5% to 90%, Storage: 5% to 90%
(non-condensing)
Regulation Compliance FCC Part 15 Class A, CE
Model ISW-621 ISW-621S15
Hardware Specications
Copper
Ports 4 x 10/100BASE-TX, auto-negotiation, auto-MDI/
MDI-X
Cable
10BASE-T : 2-pair UTP Cat. 3, 4, 5 cable (100
meters, max.)
100BASE-TX : 2-pair UTP Cat. 5, 5e, 6 cable
(100 meters, max.)
Fiber Optical
Port 2 x 100BASE-FX
Cable 50/125μm ber
62.5/125μm ber 9/125μm ber
Mode multi-mode single-mode
Distance 2km 15km
Dimensions (W x D x H) 135 x 97 x 32mm
Weight 442g
Power Requirements 12~48V DC, Redundant power with polarity
reverse protection function
Power Consumption /
Dissipation 11.6 watts / 40BTU
Installation DIN rail kit and wall mount ear
Switch Specications
Switch Processing Scheme Store-and-Forward
Address Table 2K entries
Buffer 1Mbit

12
Flow Control Back pressure for half duplex,
IEEE 802.3x pause frame for full duplex
Switch Fabric 1.2Gbps
Throughput
(Packet Per Second) 0.89Mpps @ 64Bytes
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet, 10BASE-T
IEEE 802.3u Fast Ethernet, 100BASE-TX,
100BASE-FX
IEEE 802.3x full-duplex ow control
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Temperature Operating: -10~60 degrees C
Storage: -40~85 degrees C
Humidity Operating: 5% to 90%, Storage: 5% to 90%
(non-condensing)
Regulation Compliance FCC Part 15 Class A, CE
Model ISW-621T ISW-621TS15 ISW-621TF
Hardware Specications
Copper
Ports 4 x 10/100BASE-TX, auto-negotiation, auto-MDI/MDI-X
Cable
10BASE-T : 2-pair UTP Cat. 3, 4, 5 cable (100 meters, max.)
100BASE-TX : 2-pair UTP Cat. 5, 5e, 6 cable (100 meters,
max.)
Fiber Optic
Port 2 x 100BASE-FX
Cable 50/125μm ber
62.5/125μm ber 9/125μm ber
Multi-Mode:
50/125μm ber
62.5/125μm ber
Single-Mode:
9/125μm ber
Mode multi-mode single-mode
Distance 2km 15km Depend on
SFP Module

13
Dimensions (W x D x H) 135 x 97 x 32mm
Weight 442g
Power Requirement 12~48V DC, Redundant power with polarity reverse
protection function
Power Consumption /
Dissipation 16 watts / 54BTU
Installation DIN rail kit and wall mount ear
Switch Specication
Switch Processing
Scheme Store-and-Forward
Address Table 2K entries
Buffer 1Mbit
Flow Control Back pressure for half duplex,
IEEE 802.3x pause frame for full duplex
Switch Fabric 1.2Gbps
Throughput
(Packet Per Second) 0.89Mpps @ 64Bytes
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet, 10BASE-T
IEEE 802.3u Fast Ethernet, 100BASE-TX, 100BASE-FX
IEEE 802.3x full-duplex ow control
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Temperature Operating: -40~75 degrees C
Storage: -40~85 degrees C
Humidity Operating Operating: 5% to 90%, Storage: 5% to 90%
(non-condensing)
Regulation Compliance FCC Part 15 Class A, CE

14
2. Installation
This section describes the functionalities of the Industrial Fast Ethernet
Switch’s components and guides how to install it on the desktop.
Basic knowledge of networking is assumed. Please read this chapter
completely before continuing.
2.1 Product Description
PLANET ISW-511 / ISW-621 series and ISW-511T / ISW-621T series
are 4-Port 10/100Mbps + 1/2 100FX Fiber Port Industrial Fast Ethernet
Switch with non-blocking wire-speed performance and new slim
type with IP30 metal case for easy deployment in Heavy Industrial
demanding environments.
With 1 / 1.2Gbps internal switching fabric, the Industrial Fast Ethernet
Switch can handle extremely large amounts of data in a secure
topology linking to a backbone or high capacity servers.
The Industrial Fast Ethernet Switch has 2K MAC address table and
offers wire-speed packets transfer performance without risk of packet
loss. The stable throughput of the device makes it ideal for most
Ethernet environments.
All RJ45 copper interfaces support 10/100Mbps auto-negotiation for
optimal speed detection through RJ45 Category 5, 4 or 3 cables. With
auto-MDI/MDI-X, it can detect the type of connection to any Ethernet
device without requiring special straight-through or crossover cables.
The ow control function allows Industrial Fast Ethernet Switch
supported routers and servers to directly connect to this device for
fast, reliable data transfer.

15
2.1.1 Switch Front Panel
Figures 2-1, 2-2, 2-3 and 2-4 show their front panels.
P1 P2 FAULT
LNK/ACT
4
3
2
1
LNK/ACT
10/100
TX
RX
5
ISW-511
100
P1 P2 FAULT
LNK/ACT
4
3
2
1
TX
RX
TX
RX
6
5
100
LNK/ACT
100
LNK/ACT
10/100 ISW-621
Figure 2-1 ISW-511 / ISW-511S15
Front Panel
Figure 2-2 ISW-621 / ISW-621S15
Front Panel

16
P1 P2 FAULT
LNK/ACT
4
3
2
1
LNK/ACT
10/100
TX
RX
5
ISW-511T
100
P1 P2 FAULT
LNK/ACT
4
3
2
1
TX
RX
TX
RX
6
5
100
LNK/ACT
100
LNK/ACT
10/100
ISW-621T
6
LNK/
ACT
100
P1 P2 FAULT
5
LNK/
ACT
100
4
3
2
1
LNK/ACT
10/100
ISW-621TF
Figure 2-3 ISW-511T /
ISW-511TS15
Front Panel
Figure 2-4 ISW-621T /
ISW-621TS15
Front Panel
Figure 2-5 ISW-621TF
Front Panel

17
2.1.2 LED Indicators
LED Color Function
P1 Green Lit: indicates power 1 has power.
P2 Green Lit: indicates power 2 has power.
FAULT Green Lit: indicates either power 1 or power 2 has no
power.
100 Green Fiber
Optic
Lit: indicates the Fiber port is
successfully connecting to the network
at 100Mbps.
10/100 Green Copper
Lit: indicates the Switch is successfully
connecting to the network at 100Mbps.
Off: indicates that the Switch is
successfully connecting to the network
at 10Mbps.
LNK/
ACT Green
Fiber
Optic
Lit: indicates the link through that port
is successfully established.
Blinking: indicates that the Switch is
actively sending or receiving data over
that port.
Copper
2.1.3 Switch Upper Panel
The upper panel of the Industrial Fast Ethernet Switch consists of one
terminal block connector within two DC power inputs. Figure 2-6 shows
the upper panel of the Industrial Fast Ethernet Switch.
Figure 2-6 Industrial Fast Ethernet Switch Upper Panel.

18
2.1.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial
Fast Ethernet Switch is used for two DC redundant powers input.
Please follow the steps below to insert the power wire.
1. Insert positive / negative DC power wires into contacts 1 and 2 for
POWER 1, or 5 and 6 for POWER 2.
V1- V1 + V2 - V2 +
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 345 6
Power 1 Fault Power 2
- + - +

19
Note
The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2.1.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the
Industrial Fast Ethernet Switch will detect the fault status of the power
failure, or port link failure (available for managed model) and then
forms an open circuit. The following illustration shows an application
example for wiring the fault alarm contacts.
1 2 3 4 5 6
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in
the range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 30V, max. 3A
currents.

20
2.2 Mounting Installation
This section describes how to install the Industrial Fast Ethernet Switch
and make connections to it. Please read the following topics and
perform the procedures in the order being presented.
Note
In the installation steps below, this Manual uses
IGS-801 (PLANET 8-Port Industrial Gigabit Switch) as
the example. However, the steps for PLANET Industrial
Switch and Industrial Media Converter are similar.
2.2.1 Install DIN-Rail Mounting
The DIN-Rail is screwed on the Industrial Gigabit Ethernet Switch when
out of factory. When needed to replace the wall mount application with
the DIN-Rail application on Industrial Gigabit Ethernet Switch, please
refer to the following gures to screw the DIN-Rail on the Industrial
Gigabit Ethernet Switch. To hang the Industrial Gigabit Ethernet Switch,
follow the steps below:
Step 1: Screw the DIN-rail on the Industrial Fast Ethernet Switch.