Plantronics CS530 Series User manual

CS530™
Wireless Headset System
User Guide

2
ContentsContents
Welcome 3
What’s in the Box 4
Base and Headset Basics 5
Accessories 6
Customize Your Headset 7
Change the Eartip 7
Position Your Headset 7
Connect Your Desk Phone 9
Connect the Power 9
Charge the Headset 9
Connect and Configure Your Desk Phone 10
Desk Phone (standard) 10
Check Configuration and Make a Test Call 11
Desk Phone plus HL10 Lifter (sold separately) 12
Desk Phone plus EHS Cable 14
Position Your Base 15
Your Headset 16
Headset Controls 16
Talk Time 16
Low Battery Warning 17
Muting Your Headset During a Call 17
Adjusting Your Headset Volume 17
Out of Range Warning Tones 17
Your Base 18
Base Phone Button and Switches 18
Subscription Button 18
Wideband/Narrowband Audio Switch 19
Auto Answer Switch 19
Daily Use 20
Place an Outgoing Call 20
Answer an Incoming Call 20
Conference Up to Three Additional Headsets 20
Troubleshooting 21
Headset 21
Desk Phone 21

33
Welcome
Congratulations on purchasing your new Plantronics product. This guide contains instructions
for setting up and using your CS530 Wireless Headset System.
Please refer to the separate safety instructions for important product safety information prior
to installation or use of the product.

44
What’s in the Box
Telephone interface cable
Power supply
Base Headset
Eartips

55
Base and Headset Basics
1 Call/mute LED
2 Power on/subscription LED
3 Charging LED
4 Subscription button
5 Narrowband/wideband audio switch
6 Power jack
7 Handset lifter/EHS cable jack
8 Telephone interface cable jack
9 Auto answer switch
10 Listening volume dial*
11 Speaking volume dial*
12 Configuration switch*
* For installation set up 1211
6
58 9
10
4
BACK
FRONT
Headset overview
1 Volume up button
2 Volume down button
3 Call control button
4 Indicator light
5Microphone
1
2
37
BOTTOM
Base overview
4
1235

66
Accessories
1 Electronic Hookswitch Cable (EHS) Electronically takes your desk phone handset off hook.
Enables remote call answer/end with your headset.
2HL10™ Lifter Automatically lifts handset and returns it to the cradle. Enables remote call
answer/end with your headset
2
1

77
Customize Your Headset
Customize the headset by changing the eartip, wearing it on the right or left
and optimizing the position of the microphone.
Change the Eartip
1 The headset comes with a pre-installed eartip. To install a different eartip see the following:
Remove the pre-installed eartip by pushing in and turning the eartip CLOCKwise, then pull firmly.
2 Choose the size and style of eartip that fits most comfortably. Align eartip tabs with notches in
headset. Push in firmly and twist COUNTER clockwise.
NOTE When installing a gel tip ensure the raised part of the eartip is pointed toward the curved
section of the headset as shown.
Position Your Headset
When you wear the headset, the microphone should rest as close to your cheek as possible
without touching. The microphone can be adjusted inward by pivoting the earpiece to optimize
the position of the headset.
1 Slide the headset over and behind your ear, then press gently toward your ear.

8
2 Rotate the microphone boom until it is pointed toward your mouth.
Left Ear Wearing
1 The headset can be converted for wearing on left ear as follows:
2 Turn microphone boom around.
3 Rotate microphone boom down.

9
This section describes how to connect the base to your desk phone.
Connect the Power
Plug one end of the power supply into the power jack on the back of the base and the other end
into a working power outlet. The Power On LED will be solid white.
Charge the Headset
Place the headset in the charge cradle. The charging LED on the base will flash green when
charging and turn solid green when the headset is fully charged. Charge for at least 20 minutes
prior to the first use. A full charge takes 3 hours.
=
20
Connect Your Desk Phone

1010
Connect and Configure Your Desk Phone
There are three setup options for connecting the CS530 to your desk phone. Select one of the
following and continue.
• Desk phone (standard)
• Desk phone + HL10 lifter (sold separately)
• Desk phone + EHS cable (sold separately)
NOTE If you will be using a standard desk phone set up or a desk phone with an HL10 lifter, continue
below. If you will be using the desk phone with an EHS cable, refer to Desk phone plus EHS cable
section in this guide. For further installation information refer to the EHS Getting Started guide that
came with your EHS cable or at plantronics.com/accessories.
Desk Phone (standard)
1 Connect one end of the telephone interface cable to the back of the base.
2 Disconnect the handset coil cord from the desk phone and re-connect it to the telephone
interface cable junction box.
3 Connect the remaining end of the telephone interface cable into the open handset port on the
desk phone.
NOTE Your desk phone handset will continue to work; it’s just hooked up differently.
USE
NOTE If your phone has a built-in headset port, you should only use the headset port if you will not
be using the HL10 lifter. In this configuration, you must press both the headset button on your phone
and the call control button on the headset to answer or end calls.