Plantronics Marque 2 M180 User manual

Marque 2
M180
User Guide

Contents
What's in the box 3
Headset Overview 4
Pair 5
Get Paired 5
Pair another phone 5
Charge and fit 6
Charge 6
Adjust the Fit 6
The Basics 7
Make/Take/End Calls 7
Mute 7
Adjust the Volume 8
Listen to music and more 8
More Features 9
Use two phones 9
Save Power 9
Decipher the Lights 9
Hear it Whisper 9
Disable voice commands 9
Technical Specifications 10
Support 11
2

Headset USB charge cable
Earloop Eartips
What's in the box
3

Power button
Call button
Charge port
Headset LED (indicator light)
/Volume/Mute button
Headset Overview
4

The first time you power on your headset, it begins the pairing process.
1Wearing your headset, power it on. You hear “pairing” and the headset indicator lights flash red
and white.
2Activate Bluetooth®on your phone and set it to search for new devices.
•iPhone®Settings > Bluetooth > On*
•Android™Settings > Bluetooth: On > Scan for devices*
NOTE *Menus may vary by device.
3Select “PLT_M180.”
If necessary, enter four zeros (0000) for the passcode or accept the connection.
Once successfully paired, you hear “pairing successful” and the headset indicator lights stop
flashing.
After pairing your headset to your phone, you may want to pair another phone.
1Power on your headset.
2Press and hold the Call button until you hear "pairing" or the indicator light flashes red and
white.
3Activate Bluetooth on your phone and set it to search for new devices.
4Select “PLT_M180.”
If necessary, enter four zeros (0000) for the passcode or accept the connection.
Once successfully paired, you hear “pairing successful” and the headset indicator lights stop
flashing.
Pair
Get Paired
Pair another phone
5

Your new headset has enough power to pair and make a few calls. It takes two hours to fully
charge the headset; the indicator light turns off once charging is complete.
The eartip has a thin loop that bends to gently tuck into the contours of either ear.
1Rotate the eartip on the headset or add the optional clip-on earloop to adjust the fit.
2Replace the gel eartip with one of the two alternate sizes, if it feels loose or tight in your ear.
Charge and fit
Charge
Adjust the Fit
6

Answer a call
Choose:
• Say “answer” after call is announced, or
• Tap the Call button
Answer a second call
First, tap the Call button to put the first call on hold and answer the second call. To switch
between calls, press the Call button for 2 seconds. To end the second call and retrieve the first
call, tap the Call button.
End a call
Tap the Call button to end current call.
Reject a call
Choose:
• Say “ignore” after call is announced, or
• Press Call button for 2 seconds
Redial
To call your last number dialed, double tap the Call button.
Use call waiting
First, tap the Call button to put the first call on hold and answer the second call. To switch
between calls, press the Call button for 2 seconds. To end the second call and retrieve the first
call, tap the Call button. Call waiting does not work between two paired phones.
Voice dial (phone feature)
If your smartphone has a voice-enabled assistant, press the Call button for 2 seconds and wait
for phone prompt.
You can mute the microphone during a conversation.
The Basics
Make/Take/End Calls
Mute
7

During a call, tap the Volume/Mute until you hear “mute on” or “mute off.” While the
microphone is muted, an alert repeats every 15 minutes.
Tap the Volume/Mute button to cycle through preset levels.
If your phone also has the Bluetooth A2DP (Advanced Audio Distribution Profile) stereo music
feature, then your music, podcasts, favorite Internet radio and other streaming audio can be
heard through this headset.
Adjust the Volume
Listen to music and more
8

Multipoint technology lets you pair a second phone and answer calls from either phone.
Once you have paired your two phones, it's easy to answer calls from either phone.
When on a call, you will hear a ringtone notification of the incoming call from the second paired
phone. To answer a second call from the other phone, you must end the current call (tap Call
button) so the new call automatically answers.
If you choose to not answer the second call, it will go to voicemail.
If you leave your headset powered on but out of range of your paired phone for more than 90
minutes, your headset will conserve its battery power by entering into a DeepSleep™mode.
Once back in range with your phone, tap the Call button to exit DeepSleep mode. If your phone
is also ringing, tap the Call button again to answer your call.
Your headset has an indicator light that flashes in response to a change in status or after a
button press.
Some examples of what you will see are:
• Solid red until charging complete and then off
• Flashing red and white during pairing
• Triple red flash when less than 10 minutes of talk time
• Triple white flash at incoming call
Your headset tells you about status changes. For example:
“Power on”
“Pairing successful”
“Talk time (x) hours”
“Mute on”
“Lost connection”
“Recharge headset”
This headset speaks and understands English. If you prefer to use the Call button to answer or
reject calls, you can disable the voice commands “answer” or “ignore.”
With the headset powered on, simultaneously press the Call button and Volume (+/–) button
until you see the indicator light flash blue two times. Repeat these steps to reactivate the
commands.
More Features
Use two phones
Save Power
Decipher the Lights
Hear it Whisper
Disable voice commands
9

Talk time Up to 7 hours*
Standby time Up to 11 days*
Headset weight 7 grams
DeepSleep technology • Activates when paired headset is out of range for over 90
minutes
• Provides up to 180 days* of battery readiness
Multipoint technology Use one headset to answer calls from either of two paired
Bluetooth phones
Charge connector Micro USB charging
Battery type Rechargeable, non-replaceable lithium-ion polymer
Charge time (maximum) 2 hours for full charge
Headset battery meter On-screen for iPhone, enabled by Find MyHeadset™
Bluetooth version v3.0
Bluetooth profiles Advanced Audio Distribution Profile (A2DP), Wideband
Hands Free (HFP) Profile 1.6 and Headset (HSP) Profile 1.2
Operating and storage temperature 32°F – 104°F (0 – 40°C)
NOTE * Performance is dependent upon battery and may vary by device.
Technical Specifications
10