POS-X ION 2D Bluetooth User manual

3.Bluetooth SPPMode
ION 2D Bluetooth
4.Cradle Pairing Mode
5.Connect the cradle to your computer
6.Pairing Mode
MobileDevicePairing
To pair the scanner with an iOSor Android mobile device,use the
barcodesbelow.When paired with an iOSdevice,quicklydouble
pressthe trigger to toggle the on-screen keyboard.
If you have previouslypaired thisscanner with thisdevice,navigate
to the Bluetooth settingsand select "forget"for the scanner; before
attempting to pair again.
2.HIDMode
3.Pairing Mode
1.Clear PreviousPair
Sleep Settings
The sleep setting barcodes configure how long the scanner can be
idle before powering off.
2 Minutes
*5 Minutes
Power Off
MemoryMode
While in memory mode,the scanner will store all barcodes
scanned until the "Transmit Stored Data"barcode is scanned.
Enter MemoryMode
Transmit Stored Data
Clear All Stored Data
Exit MemoryMode
Transmit Count of
Stored Barcodes
Never
Getting Started The ION 2D Bluetooth barcode scanner ispreconfigured to be
paired with the included cradle.If the scanner becomesunpaired
use the instructionsbelow to pair the scanner to the base.
After scanning each barcode,wait for the scanner to beep before
scanning the next barcode.
1.Disconnect the cradle from your computer
Vibration Settings
*Disable
Enable
CradlePairing
The ION 2D Bluetooth barcode scanner ispreconfigured to be
paired with the included cradle.To start using the scanner with a
Windows PC,simply plug in the base and start scanning.If you are
using your ION 2D Bluetooth with a mobile device,use the
instructionson the backof thisguide to pair your scanner.
If barcodes are scanning incorrectly for your software after
installing the scanner,you can usethe configuration codesin this
guide to change settings for popular symbologiesor see the full
user manual on pos-x.com for advanced configuration.
4.Open the Bluetooth settings on your device
and connect to the "Bluetooth Scanner."
After successfully pairing,the scanner will beep and the LED will
turn blueand stop flashing.
After successfully pairing,the scanner will beep and the LED will
turn blueand stop flashing.
2.Clear PreviousPair

UPC-ASettings
Use one of the barcodes below to program how the scanner will
transmit the leading 0 and last digit (check digit) for UPC-A
barcodes.
Transmit Leading 0,
Transmit Check Digit*
UPC-ESettings
Use one of the barcodes below to program how the scanner will
transmit the leading digit and last digit (check digit) for UPC-E
barcodes.
Beep Settings
Disable
*Enable
How to Program the Scanner
Scan the QRcode next to the desired configuration setting.See
the full user manual for additional program barcodes.
NOTE: All settingsmarked with *are default settings.
Resetting the Scanner
Scan the Default Settingsbarcode to reset the scanner back to
the factory default settings.
Default Settings
Terminator Settings
Aterminator isa command that is transmitted after the barcode is
scanned.To set the terminator,scan the QRcodefor the desired
terminator.To set a terminator for a single symbology,see the full
user manual.
Tab Terminator
No Terminator
*Carriage Return Terminator
[e-mail]
360.302.2222
www.pos-x.com
Blue LED Quickly
Flashing Pairing Mode
Red and Blue LED On Power On Connected
Ready to Scan
Repeated Beeping Low Battery
Green LED on Charging
Orange LED Blinks 1x
1 Beep Successful Scan
Orange LED Blinks 4x
4 Beeps Out of Scan Range
Blue LED Slowly Flashing Disconnected
Orange LED Blinks 2x
2 Beeps Successful Scan in Memory Mode
Scanner LEDsand Beep Codes
Blue LED quickly flashing Pairing Mode
Red LED on Power On
Green LED on Charging
Blue LED slowly flashing Disconnected
Blue LED on Scanner Connected
CradleLEDs
Transmit Leading 0,
No Check Digit
No Leading 0,
No Check Digit
No Leading 0,
Transmit Check Digit
Transmit Leading Digit
Transmit Check Digit
Transmit Leading Digit,
No Check Digit
No Leading Digit,
No Check Digit
No Leading Digit,
Transmit Check Digit*
Use thebarcode below to program thescanner to expand UPC-E
barcodesto UPC-A
Do Not Expand UPC-E
to UPC-A*
Expand UPC-Eto
UPC-A