Power Fist 8760654 User manual

V1.0 8760654
Please read and understand all instructions before use. Retain this manual for
future reference.

8760654 48 in. Farm Jack V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Load Capacity Lifting 4,000 lb (1,814 kg)
Clamping 750 lb (340 kg)
Winching 4,400 lb (1,995 kg)
Travel Range 4-5/16 to 40 in.
Saddle Size 4-1/8 x 1-15/32 in.
Handle Length 29-1/2 in.
Base Size 7 x 4-3/4 in.
Construction Steel
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or death
if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.

V1.0 48 in. Farm Jack 8760654
Visit www.princessauto.com for more information 3
INTRODUCTION
The 48 in. Farm Jack has multiple agricultural, off-road, winching and clamping
applications.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the
work area.
3. Store unused tools properly in a safe and dry location to prevent rust or
damage. Lock tools away and keep out of the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
3. Wear protective clothing designed for the work environment and tool.
4. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
5. Wear steel toe footwear or steel toe caps to prevent a foot injury from
falling objects.

8760654 48 in. Farm Jack V1.0
4 For technical questions call 1-800-665-8685
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use this
tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair or
replace the parts.
3. Do not overload the jack beyond its rated load capacity (see Specifications).
4. Do not use a handle extension for the jack handle.
5. Rest the jack’s base on a firm, level surface capable of sustaining the load.
Keep the surface clean and free from debris.
6. Make sure the saddle is fully under the load before operating.
7. Make sure the load is stable, so it does not shift when lifting or lowering.
8. Make sure there is enough clearance around the jack and the load during
lifting or lowering actions.
9. Before lifting a vehicle, apply the emergency brake and block all wheels.
10. Support the load with jack stands or a support structure of adequate
capacity immediately after lifting. Never work under a load without
additional support devices.
11. The jack must remain in a static position for lifting and lowering loads.
Never move a load that is elevated on the jack. Ensure the load remains
stable at all times.

V1.0 48 in. Farm Jack 8760654
Visit www.princessauto.com for more information 5
12. Do not push a load off the jack; lower carefully.
13. Before lowering load, ensure that there are no obstructions underneath
and that all people are standing clear.
14. Do not place your hands between the moving components.
15. The jack must have a minimum load of 110 lb (50 kg) to engage the ratchet
system when Iowering the load. Otherwise the large runner and load wiII
drop without resistance and may cause a serious injury.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the missing
part before operating. Failure to do so could result in a malfunction and
personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.
Contents: • Farm Jack
ASSEMBLY & INSTALLATION
Numbered references in parenthesis (#1) refer to the included Parts List.
The Farm Jack is preassembled.
OPERATION
WARNING! Do not place any part of your body under the load without jack
stands or a support structure capable of handling the load in place. The jack is
not designed to maintain heavy loads for long periods of time
WARNING! Always have an escape route in place should the load become
unstable or slip off the jack.
RAISING A LOAD
1. Place the jack beneath the load.
2. Position the large runner (#19) saddle slightly
below the contact point of the load.
3. Lift the reversing latch (#17) to the UP position
and ensure it is locked in place, with the reversing
switch’s tooth firmly engaged in the notch on the
reversing latch. Refer to Fig. 1.
Fig.
1