Power Tec 71768 User manual

INSTRUCTION SHEET
Telescoping Fence
WARNING
For your own safety, read the machine's instruction manual before
using any accessory. Failure to heed these warnings may result in
serious personal injury and damage to the tool and theaccessory.
• Before using the Telescoping Fence, read and follow all
instructions and safety information provided.
• Always keep hands clear of the blade, cutter, sanding disc/belt.
• Before making adjustments to the Telescoping Fence, turn
off the power, allow the blade, cutter or sanding disc/belt to
come to a complete stop and unplug the machine.
• Ensure handle and lock knob are tight beforeusing.
• Before turning on the power afteradjustments, ALWAYS verify
there is a safe clearance between the blade and fence.
UNPACKING CONTENTS
NOTE: Check for shipping damage. Check immediately whether
all parts and accessories are included.
ITEM DESCRIPTION QTY
A Telescoping Fence, 3"x1-3/8"x20" 1
BLock Knobs 2
C12" Movable Scale 1
Figure 1
WARNING
Risk of accidental starting and serious personal injury.
Unplug the machine before attaching the Telescoping Fence.
THE TELESCOPING FENCE
1. See Figure 2. The I-Beam Extender with 3" Fence End allows
an additional 17" extension. To extend the Fence and/or
switch Fence position, loosen the two Lock Knobs and pull the
3" Fence End out to desired length and secure Lock Knobs.
2. The I-Beam Extender can be used on either end of the Fence. To
change sides, loosen the Lock Knobs, remove the 3" Fence End
with I-Beam Extender. Locate the I-beam prole on the other end
of the Fence and insert I-Beam into the Fence. Tighten Knobs.
Figure 2
INSTALL THE FENCE ONTO
A MITER GAUGE (Not Included)
Figures 3-4. Shown using POWERTEC 71767 Miter Gauge
(Sold separately)
3. See Figure 3. Remove Fence Lock Knob. Loosen the two
5/16" Round Knobs on the Miter Gauge and slide the T-bolts
into the Fence slot.
Figure 3
4. See Figure 4. Insert I-Beam Extender with 3"Fence End.
Set to desired length. Tighten 5/16" Round Knobs on Miter
Gauge. Reinsert Fence Lock Knobs and tighten to secure
I-Beam Extender in position.
Figure 4
Model No. 71768
23-0306

INSERT A FLIP STOP (Sold Separately)
Slide the T-Bolt into the slot on the top of the Fence or 3" Fence
End (shown with 3" Fence End). Position the arm as needed
and tighten the AdjustmentKnob.
Figure 5
FEATURES
The Fence is equipped with a high quality 12" Movable Scale.
Calibrate the scale by using the corner edge of the ip stop (not
included) to identify the alignment point. Tighten the adjustment
knob on the ip stop to secure in place.
Figure 6
WARNING
When servicing, use only identical replacement parts. Use of
any other parts may create a hazard or cause product damage.
To ensure safety and reliability, all repairs should be performed
by a qualied service technician.
WARNING
Keep the Telescoping Fence dry, clean, and free from oil
and grease. Always use a clean cloth when cleaning. Never
use brake uids, gasoline, petroleum-based products or any
strong solvent to clean the Telescoping Fence. Chemicals can
damage, weaken or destroy plastic which may result in serious
personal injury.
Southern Technologies, LLC • Chicago, IL 60606
Put these instructions and the original sales invoice
in a safe, dry place for future reference.
Visit us on the web at www.powertecproducts.com