Powermatic 2700 Service manual

Operating Instructions and Parts Manual
Model PM2700 Shaper
Model: 2700
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, TN 37086 Part No. M-1280100C
Ph.: 800-274-6848 Revision E4 01/2011
www.powermatic.com Copyright © 2011 Walter Meier (Manufacturing) Inc.

2
Warranty and Service
Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our
Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter
Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance
and major repair on your POWERMATIC
®
tools. For the name of an Authorized Service Center in your area call 1-800-274-6848.
MORE INFORMATION
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local
Walter Meier distributor, or visit powermatic.com.
WARRANTY
POWERMATIC products carry a limitedwarrantywhich varies in duration based upon the product.
WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools, abrasives
and other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warranty covers only the initial purchaser of the product.
WHAT IS THE PERIOD OF COVERAGE?
The general POWERMATIC warranty lasts for thetime period specified in the product literature of each product.
WHAT IS NOT COVERED?
The Five Year Warranty does not cover products used for commercial, industrial or educational purposes. Products with a Five
Year Warranty that are used for commercial, industrial or education purposes revert to a One Year Warranty. This warranty does
not cover defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair or
alterations, or lack of maintenance.
HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name of the
location nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection discloses a defect, wewill repair or replace the product, or refund the purchase price, at our option.
We will return the repaired product or replacement at our expense unless it is determined by usthat there is no defect, or that the
defect resulted from causes not within the scope of our warranty in which case we will, at your direction, dispose of or return the
product. In the event you choose to have the product returned, you will be responsible for the handling and shipping costs of the
return.
HOW STATE LAW APPLIES
This warranty gives you specific legalrights; youmay also have other rightswhich vary from state to state.
LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED
WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY
AND FITNESS AREEXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONMAY NOT APPLY TOYOU.
WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR
INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONOF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSIONMAY NOT APPLYTO YOU.
Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general information and are
not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice, those alterations to parts,
fittings, and accessory equipment which they may deem necessary for any reason whatsoever.

3
Table of Contents
Warranty and Service..........................................................................................................................2
Table of Contents ...............................................................................................................................3
Warnings............................................................................................................................................4
Warning .............................................................................................................................................6
Introduction........................................................................................................................................7
Specifications.....................................................................................................................................7
Unpacking..........................................................................................................................................8
Shipping Contents...........................................................................................................................8
Installing ............................................................................................................................................8
Assembly...........................................................................................................................................9
Mounting the Fence.........................................................................................................................9
Electrical Connections.........................................................................................................................9
General Information.........................................................................................................................9
Extension Cords............................................................................................................................10
Adjustments .....................................................................................................................................11
Fence Assembly Movement...........................................................................................................11
Coplanar Alignment.......................................................................................................................12
Ram Dial Calibration......................................................................................................................13
Spindle Gib Adjustment .................................................................................................................14
Featherboard Hold-downs..............................................................................................................14
Spindle Assembly Installation.........................................................................................................15
Spindle Assembly Removal............................................................................................................15
Shaper Cutter Installation...............................................................................................................16
Router Collet (Optional) Installation ................................................................................................16
Changing Cutter Speed .................................................................................................................17
Drive Belt Tension.........................................................................................................................17
Precision Miter Gauge ...................................................................................................................18
Handwheel Adjustments ................................................................................................................11
Belt Replacement..........................................................................................................................17
Operating Controls............................................................................................................................19
Start/Stop.....................................................................................................................................19
Safety Key....................................................................................................................................19
Digital Readout .............................................................................................................................19
Operations .......................................................................................................................................20
Special Cuts.....................................................................................................................................29
Troubleshooting for PM2700 Shaper..................................................................................................32
Optional Accessories ........................................................................................................................33
Parts................................................................................................................................................33
Ordering Replacement Parts..........................................................................................................33
Table – Parts List..........................................................................................................................34
Table – Assembly Drawing.............................................................................................................35
Fence – Parts List.........................................................................................................................36
Fence – Assembly Drawing............................................................................................................37
Frame and Motor – Parts List.........................................................................................................38
Elevator – Parts List......................................................................................................................40
Elevator – Assembly Drawing.........................................................................................................41
Caster Assembly – Parts List .........................................................................................................42
Caster Assembly Drawing..............................................................................................................43
Spindle Assembly – Parts List........................................................................................................44
Spindle Assembly Drawing- ...........................................................................................................45
Cabinet and Base – Parts List........................................................................................................46
Cabinet and Base..........................................................................................................................48
Wiring Diagrams...............................................................................................................................49
3HP/5HP, 230V, 1Phase................................................................................................................49
5HP, 230V, 3Phase.......................................................................................................................50
5HP, 460V, 3Phase.......................................................................................................................51

4
Warnings
1. Read and understand the entire owner's manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This shaper is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a shaper, do not use until proper training
and knowledge have been obtained.
5. Do not use this shaper for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury
that may result from that use.
6. Always wear approved safety glasses/face shields while using this shaper. Everyday eyeglasses only
have impact resistant lenses; they are not safety glasses.
7. Before operating this shaper, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, shaping, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•Lead from lead based paint.
•Crystalline silica from bricks, cement and other masonry products.
•Arsenic and chromium from chemically treated lumber.
10. Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
11. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source. A
machine under repair should be RED TAGGED to show it must not be used until maintenance is
complete.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
20. Make your workshop child proof with padlocks, master switches or by removing safety keys.

5
21. Keep visitors a safe distance from the work area. Keep children away.
22. Make your workshop child proof with padlocks, master switches or by removing safety keys.
23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
24. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
26. Use recommended accessories; improper accessories may be hazardous.
27. Maintain tools with care. Keep cutter sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
28. Check the cutter for cracks or missing teeth. Do not use a cracked cutter or one with missing teeth or
improper set. Make sure the cutter is securely locked on the arbor.
29. Keep hands clear of the cutter area. Do not reach past the cutter to clear parts or scrap with the
shaper running. Avoid awkward operations and hand positions where a sudden slip could cause your
hand to contact the cutter.
30. Do not attempt to shape boards with loose knots or with nails or other foreign material, on its surface.
Do not attempt to shape twisted, warped, bowed or “in wind” stock unless one edge has been jointed
for guiding purposes prior to shaping.
31. Do not attempt to shape long or wide boards unsupported where spring or weight could cause the
board to shift position.
32. Always use safety devices for all operations where they can be used.
33. Be sure to check the direction of spindle rotation before use.
34. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
35. Do not stand on the machine. Serious injury could occur if the machine tips over.
36. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
37. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.

6
Warning
Short stock – Never shape stock less than 12
inches in length without special fixtures. Where
practical, shape longer stock and cut to size.
12 inch rule – When shaping, never allow your
hands to come closer than 12 inches to the
cutters.
Hand safety – Never pass the hands directly
over, or in front of, the cutters (Figure A). As one
hand approaches the 12 inch radius point, remove
it (or the push stick) in an arc motion and
reposition hands 12 inches beyond the cutters.
Blind cut – When blind cutting, the workpiece is
positioned on top of the template. This keeps the
cutter(s) cutting only the underside of the
workpiece and provides a "distance" guard for the
operator.
Cutter Clearance – With the power disconnected,
always rotate the spindle by hand with any new
set-up to ensure proper clearance with the cutters.
At the same time, check to be sure the cutterhead
is turning in the correct direction.
Stock feed – Feed stock opposite to the direction
of the cutter rotation (Figure B). Never back stock
out of the cutter once the cut has been started.
Instead, pull the stock straight out away from
cutter and begin the cut again.
Guide pin – Whenever possible, use a guide pin
when performing pattern shaping and collar
shaping operations.
Tool maintenance – Clean and sharp tools give
safer and better performance. Dull tools can
cause kickbacks and excessive chatter. Before
making a cut, always check the condition and
adjustment of the tools. Never use a tool that is
not balanced and rated for the selected RPM.
Spindle speed – Do not operate tools at speeds
higher than rated by the manufacturer.
Cutter selection – Use only those cutters
designed to be used on the machine, and mount
only safety type cutters on the spindle.
Stock condition – The danger of kicked-back
stock can occur when the stock has knots, holes,
or foreign objects such as nails. Warped or in-wind
stock should first be jointed on one surface before
attempting to use it on the shaper.
Figure A
Figure B

7
Introduction
This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and
maintenance procedures for a Powermatic Model PM2700 Shaper. This manual contains instructions on
installation, safety precautions, general operating procedures, maintenance instructions and parts
breakdown. This machine has been designed and constructed to provide years of trouble free operation if
used in accordance with instructions set forth in this manual. If there are any questions or comments,
please contact either your local supplier or Walter Meier. Walter Meier can also be reached at our web
site: www.waltermeier.com.
Specifications
Model Number......................................................................................................................... PM2700
Motor (TEFC Capacitor Start Induction) Stock Number
3HP, 1 Phase, 230V, 60Hz, 14A..........................................................................................1280100C
5HP, 1 Phase, 230V, 60Hz, 22A..........................................................................................1280101C
5HP, 3 Phase, 230V/460V-prewired 230V (for 460V see Note below), 60Hz, 13/6.5A............. 1280102C
Table Size (L x W)..................................................................................................................40" x 30"
Table Height from Floor..............................................................................................................35-1/2”
Spindle Size (Standard) ..............................................................................3/4", 1-1/4" Interchangeable
Router Bit Collet Size (Optional) ..............................................................................................1/4", 1/2"
Spindle Capacity Under Nut:
3/4” Spindle (provided) .............................................................................................................3-3/4"
1-1/4” Spindle (provided)................................................................................................................6”
1” Spindle (optional accessory).................................................................................................5-3/4”
1/2” Spindle (optional accessory) ..............................................................................................3-1/8”
30mm Spindle (optional accessory)...........................................................................................3-1/2”
Spindle Travel...................................................................................................................................4"
Spindle Speeds (RPM).......................................................................................7500, 10000, reversible
Table Opening Diameter...............................................................................................................7.33"
Insert Opening Diameters...........................................................................................2.55", 4.16", 5.75"
Fence Size (x 2) ................................................................................................4-7/8" (H) x18-3/4" (W)
Dust Collection Minimum CFM Required..........................................................................................600
Dust Port Diameter............................................................................................................................4”
Overall Dimensions .......................................................................................40" (L) x 37" (W) x 45" (H)
Weight.................................................................................................690 lbs (Shipping), 664 lbs (Net)
Note: For 460V operation, magnetic switch (Part No. PM2700-114C) must be purchased separately and
installed. A qualified electrician is recommended.
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Walter Meier reserves the right to change specifications at any time and without
prior notice, without incurring obligations.
Read and understand the entire contents of this manual before attempting
assembly or operation! Failure to comply may cause serious injury

8
Unpacking
Remove box and wood crating completely from
around shaper. Check for shipping damage. Report
any damage immediately to your distributor and
shipping agent. Do not discard any shipping
material until the Shaper is assembled and running
properly.
Compare the contents of your container with the
parts lists on this page to make sure all parts are
intact. Missing parts, if any, should be reported to
your distributor. Read the instruction manual
thoroughly for assembly, maintenance and safety
instructions.
Shipping Contents
Referring to Figure 1:
Main Shaper Container
1 Fence Assembly (A)
1 Cabinet and Base (B)
Hardware and included tools consist of the
following items:
2 Lock Handle (C)
2 M13 Flat Washer (D)
1 Miter Gauge Assembly (E)
1 Draw Bar (F)
1 1-1/4" Spindle (G)
1 3/4" Spindle (H)
2 Spindle Nut (I)
3 Insert Rings – 2.55”, 4.16”, 5.75” (J)
4 M10 Socket Head Cap Screw (K)
4 M10 Lock Washer (L)
1 Starting Pin (M)
1 8 mm Hex Wrench (N)
1 Crosspoint/Flathead Screwdriver (O)
1 Wrench (P)
Installing
1. Unbolt the shaper from the skid.
2. Carefully slide the shaper from the pallet onto
the floor.
Make sure that the casters do
not get damaged when removing from the skid.
The Shaper should be placed in an area with a
sturdy level floor, good ventilation and sufficient
lighting. Leave enough space around the machine
for mounting extension wings and rail assemblies,
and loading and off-loading stock and general
maintenance work.
Main Shaper Container
Hardware
Figure 1

9
Cleaning
Exposed metal surfaces, such as the table top and
extension wings, have been given a protective
coating at the factory. This should be removed with
a soft cloth moistened with kerosene. Do not use
acetone, gasoline, or lacquer thinner for this
purpose. Do not use solvents on plastic parts, and
do not use an abrasive pad because it may scratch
the surfaces.
Assembly
Mounting the Fence
Referring to Figure 2:
1. Place the fence assembly (A) on the table (B),
lining up the four mounting holes (C) on the
bracket with the threaded holes (D) on the rear
of the table above the dust port (E).
2. Hand fasten with four each M10 hex socket
cap screws (F) and M10 lock washers (G). Do
not tighten at this time.
3. Place two M13 flat washers (H) on two lock
handles (J). Insert the lock handles through
slots (K) on each side of the base. Partially
thread the lock handles (J) into two mounting
holes (L) on the table. Do not tighten at this
time.
4. Turn the adjust knob on the bracket to position
the fence all the way to the rear.
5. Tighten the lock handles (J) sufficiently to
prevent the fence from movement.
Electrical Connections
Electrical connections must be
made by a qualified electrician in compliance
with all relevant codes. This machine must be
properly grounded to help prevent electrical
shock and possible fatal injury.
General Information
A power plug is not provided with the Model
PM2700. You may either connect the proper
UL/CSA listed plug or “hardwire” the machine
directly to your electrical panel provided there is a
disconnect near the machine for the operator.
Consult electrical drawings on pages 47-48 for
further clarification of wiring setup.
Figure 2

10
This machine must be
g
rounded. Groundin
g
provides a path of least resistance to help divert
current away from the operator in case of electrical
malfunction.
Make sure the voltage of your power supply
matches the specifications on the motor plate of the
machine.
The PM2700 Shaper should be connected to a
dedicated circuit, and protected by a circuit breaker
or time delay fuse, with minimum amp ratings as
shown in Table 1. Local codes take precedence
over recommendations.
Voltage Conversion (3 Phase Shaper only)
On the 3 phase model, to convert from 230V to
460V, replace the 230V switch with the 460V
switch (not included, order part no. PM2700-114C),
and re-wire the incoming leads to the motor as
shown on the diagram inside the cover of the motor
junction box. A similar diagram is also included in
the back of this manual. (Figure 3 shows a
summary of the lead changes for 230V to 460V
conversion.) Note: In case of discrepancies, the
diagram in the motor junction box should take
precedence.
Extension Cords
The use of extension cords is discouraged. Try to
position equipment within reach of the power
source. If an extension cord becomes necessary,
make sure the cord rating is suitable for the
amperage listed on the machine's motor plate. An
undersize cord will cause a drop in line voltage
resulting in loss of power and overheating.
The chart in Table 2 shows the correct size cord to
use based on cord length and motor plate amp
rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Model Recommended circuit
*
1280100C (3HP 1PH 230V
)
30 Amp
1280101C (5HP 1PH 230V
)
40 Amp
1280102C (5HP 3PH 230V
)
30 Amp
1280102C (5HP 3PH 460V
)
15 Amp
*subject to local codes
Table 1
Figure 3
Amps
Extension Cord Length *
25
feet 50 feet 75 feet 100 feet 150 feet 200 feet
< 5 16 16 16 14 12 12
5 to 8 16 16 14 12 10 NR
8 to 12 14 14 12 10 NR NR
12 to 15 12 12 10 10 NR NR
15 to 20 10 10 10 NR NR NR
21 to 30 10 NR NR NR NR NR
*based on limiting the line voltage drop to 5V at 150% of the
rated amperes.
NR: Not Recommended.
Table 2

11
Adjustments
When changing tools, making
adjustments, or doing clean-up and maint-
enance, always turn the machine off and unplug
the machine from its power source.
Fence Assembly Movement
Referring to Figure 4:
The adjustment controls of the fence assembly are
as follows:
A – Fence Assembly Lock Knob – to secure fence
assembly to table
B – Fence Adjustment Knob – moves fence
assembly forward or back
C – Lock Knob – to secure the infeed and outfeed
fences
D – Infeed/Outfeed Ram Adjust – fine adjustment
for infeed or outfeed fence
E – Lock Knob – loosening permits side to side
adjustment of infeed or outfeed fence
F – Lock Knob – loosening permits vertical
adjustment of guard (H)
G – Lock Knob – loosening permits
backward/forward adjustment of guard (H)
Figure 4
Handwheel Adjustments
Referring to Figure 5:
The front handwheel (B) controls the spindle
height.
The side handwheel (C) controls the casters. The
Model PM2700 has a retractable caster system that
can be extended to permit the shaper to be rolled
from one location to another.
Spindle height
1. Loosen the lock knob (B) on the spindle height
adjust handwheel (A).
2. Turn the handwheel (A) clockwise to raise and
counterclockwise to lower the spindle.
3. Tighten the lock knob (B).
Caster system adjustment
Retractable casters can be extended permitting the
shaper to be moved as follows:
1. Turn the handwheel (C) clockwise to extend
the casters, raising the shaper.
Note: Because of the weight of the machine,
both hands may be needed to turn the
handwheel. Raise the shaper just enough to
permit moving to another location.
When the shaper has been repositioned:
2. Retract the casters by turning the hand-
wheel (C) counterclockwise.
Figure 5

12
Coplanar Alignmen
t
Follow steps 1–5 to determine if alignment is
necessary. Steps 6–9 will guide you through the
alignment if required.
Verifying that fences are coplanar
1. Remove the guard and spindle attachment.
2. Adjust the fence assembly (A) so it is
positioned approximately at midpoint and lock
(B).
3. Place a straightedge (F) on the table pressed
against the infeed (E
1
) and outfeed fences (E
2
).
4. Unlock the fence lock knobs (D
1
, D
2
).
5. With the ram adjust dials (C
1
, C
2
) adjust the
position of either fence as required to bring
both fences in-line (coplanar alignment) using
the straightedge as the point of reference.
No adjustment is required if both fences are flush
with the straightedge as shown in Figure 7. Pro-
cede to Ram Dial Calibration (step 00).
Adjustment is required if the fences appear
skewed (Figure 8). Continue with Coplanar Adjust-
ment (following steps).
Coplanar Adjustment
Determine which fence is skewed (in this example:
G
1
, Fig. 8), which will require adjustment while the
remaining fence (G
2
) will serve as the reference
point.
6. Remove both fences and place the straight-
edge against the infeed and outfeed fence
castings (Figure 9).
7. Lock the reference fence (D
2
) and unlock the
skewed fence (D
1
).
Read step 8 completely before attempting.
8. Maintain steady pressure of the straightedge
against the fence castings (H, Fig. 9). At the
same time, attempt to bring both fences into
alignment as shown in Figure 10. This is
accomplished by alternately making incremen-
tal adjustments to four setscrews (L, Fig. 11)
on the front face of the casting (K, Fig. 11) with
a 2mm hex wrench, followed by repositioning
the casting with the micro adjust dial (J, Fig.
11) as required.
Important: It is recommended that the
adjustment setscrews (K, Fig. 11) be rotated in
1/16th increments or less at a time.
Alignment is complete when the skewed and
reference fence castings are coplanar (in-line) as
shown in Figure 10.
9. Replace both fences and secure.
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11

13
Ram Dial Calibration
The guard and spindle should be removed.
Referring to Figure 12:
1. Loosen the infeed fence lock knob (E), then
turn the infeed ram dial (D) counterclockwise to
bring the infeed fence (F) back all the way until
the limiter setscrew (P) touches the head
casting (M). Then retighten the lock knob (E).
2. If necessary, loosen two setscrews on the
infeed ram dial (D) with a 2mm hex wrench and
align the zero on the dial with the indicator
mark. Then tighten the setscrews.
3. Next, loosen the outfeed fence lock knob (B)
and turn the outfeed ram dial (A) counter-
clockwise to bring the outfeed fence (C) all the
way back.
4. Place a straightedge (G) on the table against
both fences.
If both fences are flush with the straightedge (K)
and the outfeed ram dial (A) indicates zero, no
further action is necessary.
If alignment is necessary (J):
5. Slide the outfeed fence (C) aside to reveal the
limiting setscrew (P) on the fence casting (N).
6. Loosen the hex locking nut (O) with a 10mm
wrench and back out the limiting setscrew (P)
with a 3mm hex wrench to permit a sufficient
backward and forward adjustment range for the
outfeed fence (C).
7. Slide the outfeed fence (C) back onto the
casting and secure.
8. Loosen the outfeed fence lock knob (B).
9. While maintaining pressure (H) on the
straightedge (G) against the fences (C, F),
adjust the outfeed ram dial (A) until both fences
are in-line (K).
After proper alignment is made:
10. Slide the outfeed fence (C) aside again.
11. Turn the limiting setscrew (P) in (turn cw) until
it comes in contact with the head casting (M)
12. Tighten the hex locking nut (O) with a 10mm
wrench while maintaining the setscrew position
with the 3mm hex wrench.
13. Replace the outfeed fence and secure.
14. Loosen the two set-screws (2mm hex wrench)
on the outfeed ram dial (A) and align the zero
on the dial with the indicator mark. Then tighten
the setscrews.
-- Outfeed side is mirror image
Infeed side fence casting
Figure 12

14
Spindle Gib Adjustment
Referring to Figure 13:
The spindle housing gib on your machine is factory
adjusted and initially should not require readjust-
ment. After a period of use the gib may wear and
become loose, introducing play and potentially
causing the spindle (A) to vibrate. This requires
adjustment.
To adjust (refer toFigure 13):
1. With a 12mm wrench, loosen four jam nuts (B)
that secure the gib setscrews (C).
2. With a 4mm hex wrench, tighten each setscrew
1/8 or less turn starting with the lowest one,
followed by the uppermost one, then the two
middle setscrews.
If this is not enough to remove the table play,
repeat this step until the play is removed.
Note: If the gibs are too tight the front handwheel
(A, Fig. 3) that controls the spindle height will be
difficult to turn.
3. When adjustment is complete, hold the set-
screws (C) in position with the 4mm hex
wrench to maintain the setting while tightening
the jam nuts (B) with the 12mm wrench.
Featherboard Hold-downs
Referring to Figure 14:
The PM2700 Shaper comes equipped with two
featherboard hold-downs (A, B) mounted on the
infeed and outfeed fences.
1. Loosen lock handles (C) and lock knobs (D).
2. Slide the hold-down guides to the desired
position along the fence and tighten the lock
handles (C).
3. Place the workpiece (E) on the table against
the fence and under the hold-down guide (A).
4. Adjust the featherboard stay to put moderate
pressure on the workpiece, then tighten the
lock knob (D).
Figure 13
Figure 14

15
Spindle Assembly Installation
Refer to Figure 15. The fence guard (A) has been
removed for clarity.
The spindle assembly (B) is mounted to the arbor
(C) and secured with a draw bar (J) and nut (E).
Use the following procedure to install the spindle
assembly. Reverse the order to remove the
spindle.
When changing tools, making
adjustments, or doing clean-up and maint-
enance, always turn the machine off and unplug
the machine from its power source.
1. Raise the arbor (C) all the way using the
handwheel located on the front of the cabinet.
Locking the Arbor
2. Locate the spindle lock (F) accessible through
the door on the right side of the cabinet. Pull
out and rotate 90º right or left, resetting the
knob into the indent.
Turn the arbor (C) by hand until it locks, then
verify that it will not rotate.
Installing the Spindle Assembly
3. Thread the nut (E) onto the threaded end of the
spindle (D) in the direction indicated by arrows
(A
1
, A
2
). Tighten securely by hand.
4. Thread the spindle assembly (B) and nut (E)
onto the arbor (C) and hand tighten only.
5. Insert the draw bar (J) through the opening in
the shaft (H) just below the drive belt (G). Turn
clockwise, fastening and securing it to the
spindle. Tighten the draw bar (J) with the
provided wrench (K).
6. Tighten the nut (E) with the wrench (K).
Shaper Cutter installation is described in the
following section. Note that at this time the
spindle holder is still locked.
Spindle Assembly Removal
Referring to Figure 15:
The spindle holder must be locked as described in
Spindle Assembly Installation, step 2.
1. Remove the draw bar (J).
2. Loosen the nut (E) then, using the wrench (K)
continue to turn until the spindle attachment
breaks free of the arbor.
Figure 15

16
Shaper Cutter Installation
Note: Spindle installation is described in the
previous section.
When changing tools, making
adjustments, or doing clean-up and maint-
enance, always turn the machine off and unplug
the machine from its power source.
Locking the Spindle
1. Locate the spindle lock (F, Fig. 15) accessible
through the door on the right side of the
cabinet. Pull out and rotate 90º right or left,
resetting the knob into the indent.
Attempt to turn the spindle (B, Fig. 15) by hand
to verify that it is locked and will not rotate.
Installing the Shaper Cutter
Referring to Figure 16:
1. Place the shaper cutter (A) (not included) onto
the spindle, oriented in the proper direction.
2. Place the spacers (B) and keyed collar (C) onto
the spindle.
Note: Spacers come in several widths and the
stacked selection (B) must be such that the top
of the keyed collar (C) sits slightly above the
top of the spindle (D). This will ensure sufficient
pressure to properly secure the shaper cutter
(A) when installation is complete.
3. Install the pronged washer (E) and socket head
cap screw (F). Tighten screw with the 8mm hex
wrench provided.
Unlocking the Spindle
4. Pull out the spindle lock (F, Fig. 15) accessible
through the door on the right side of the
cabinet. Rotate 90º right or left, resetting the
knob into the indent.
Using gloves to prevent injury from the
shaper cutter, turn the spindle (B) by hand to
verify that it turns freely.
Router Collet (Optional) Installation
1. Locate the spindle lock (F, Fig. 15) accessible
through the door on the right side of the
cabinet. Pull out and rotate 90º right or left,
resetting the knob into the indent.
Attempt to turn the spindle (B, Fig. 15) by hand
to verify that it is locked and will not rotate.
2. Place the router collet (A, Fig. 17) onto the
spindle (B, Fig. 17) and secure with the
wrench (K, Fig. 15) provided.
Figure 16
Figure 17
3. Unlock the spindle by pulling out the lock knob
(F, Fig. 15) accessible through the door on the
right side of the cabinet. Rotate 90º right or left,
resetting the knob into the indent.
Turn the router collet (A, Fig. 17) by hand to
verify that it turns freely.

17
Changing Cutter Speed
Referring to Figure 18:
The Model PM2700 Shaper is equipped with
pulleys that allow you to change the spindle speed.
The belt (B) placed on the upper pulleys (as shown
in Figure 16) provides 7,500 RPM spindle speed.
Placing the belt on the lower pulleys provides
10,000 RPM spindle speed.
To change speed (refer to Figure 16):
1. Disconnect the machine from the power
source.
2. Open the door of the cabinet.
3. Remove the belt tension by moving the belt
tension handle (A) to the unlock (left) position.
This allows the motor (E) to swivel on its
mounting hinge.
4. Move the drive belt (B) to the other set of
grooves (C).
5. Lock the belt tension handle (A), securing the
motor (E) and placing tension on the drive
belt (C).
Drive Belt Tension
Referring to Figure 18:
The drive belt should have sufficient tension to
prevent slippage when the machine is in operation.
If the tension on the belt needs adjustment:
1. Disconnect the machine from the power
source.
2. Open the door of the cabinet.
3. With a 17mm wrench, loosen the lock nut (G)
on the belt tension assembly (refer to inset for
loosening direction).
4. Adjust the hex bushing (F) with a 17mm
wrench (refer to inset for adjustment direction)
for proper tension on the belt (B). The tension
handle (A) must be in the locked position (right)
while performing this step.
Note: Two 17mm wrenches are required for the
next step.
5. Maintain the position of the hex bushing (F)
with one wrench while tightening the lock
nut (G) with the other.
Figure 18
Belt Replacement
Referring to Figure 18:
Replace the drive belt (B) as follows:
1. Disconnect the machine from the power
source.
2. Open the door of the cabinet.
3. Remove the belt tension by moving the belt
tension handle (A) to the unlock (left) position.
This allows the motor (E) to swivel on its
mounting hinge.
4. Work the drive belt down all the way past the
pulleys.
5. Continue sliding the belt down on the left side
until it is free from the spindle (C), then remove
the belt over the top of the motor pulley (D).
6. Install the new belt by following these steps in
reverse.

18
Precision Miter Gauge
Setting the miter gauge angle
Referring to Figure 19:
The precision miter gauge has a rack and pinion
adjustment for setting the angle. To operate:
1. Slide the miter gauge into one of the slots on
the table top.
2. Loosen lock handle (A).
To adjust the body (B) of the miter gauge to the
desired angle:
3. Pull the spring-loaded knob (C) out and turn
until the body (B) of the miter gauge is at the
desired angle as indicated on the scale.
4. Tighten the lock handle (A).
Indent settings
There are indents at the 0º, 30º and 45º right and
left positions. At these settings, release the
knob (C) to engage the stop rod. Then tighten the
lock handle (A).
Note: Do not rely solely on the indents for an
accurate setting. After the stop rod engages at the
0º, 30º and 45º positions, make a fine adjustment
with the knob (C), if necessary, setting it against
the scale indicator.
Extension plate
The extension plate (D) can be adjusted by sliding
to the right or left or removed entirely.
To adjust – loosen two lock handles (E), position
the extension plate and tighten the lock handles.
To remove – slide the extension plate completely
off and remove the lock handles (E) and mounting
hardware.
Calibrating the miter gauge
1. Place the miter gauge in one of the slots (H) on
the table top.
2. Set the miter gauge to 90º (0º setting on the
scale) by loosening the lock handle (A), then
pulling the spring-loaded knob (C) out and
turning the body (B) until 0º is indicated on the
scale (F).
3. Measure the accuracy of the gauge against the
slot with a combination square.
If adjustment is necessary:
4. Adjust the body (B) until it is perfectly square
(90º) to the miter slot (H).
Figure 19
5. Tighten the lock handle (A).
Verify that the scale indicator (G) reads 0º. If further
adjustment is necessary:
6. Loosen the screw (F) and adjust the
indicator (G) until it reads 0º
7. Tighten the screw (F).
The miter gauge should fit snugly within the miter
slot while still sliding easily. The bar of the miter
gauge has two slots, each with a set screw. Rotate
one or both of these set screws with a hex wrench
as needed to eliminate any play between the miter
gauge bar and miter slot.

19
Operating Controls
Start/Stop
Power Indicator Light – The start switch has a
power indicator lamp which is on whenever
there is power connected to the shaper, not
just when the shaper is running. Do not assume
that no light means there is no power to the
machine. If the bulb is bad, there will be no
indication. Always check before use.
Do not rely that no light
means no power to the machine. Always
check for power first. Failure to comply may
cause serious injury!
Referring to Figure 20:
Start – Press the green start switch (see Note).
When power is connected to the machine, the
green light is always on regardless of whether
the shaper is running or not.
Note: In addition, the switch on the digital
readout must be set to forward (or reverse) and
the cabinet door must be closed.
Stop – Press the red switch to stop.
Reset – In the event that the shaper stops
without pressing the stop button, as the result of
a tripped fuse or circuit breaker, etc.:
1. Press red button to reset
2. Press the green button to restart the
machine.
Figure 20
Safety Key
The start/stop switch on the Model PM2700
comes equipped with a magnetic safety key.
When in place on the switch as shown in Figure
20 the magnetic safety key trips a relay which
will allow the machine to start and stop when the
respective switches are pressed. Being
magnetic, the lock can be removed to make the
machine inoperable and can be hidden for safe
storage by attaching it underneath the rail or
another magnetic surface.
When using the shaper, place the key on the
switch cover lining up the arrow on the key with
the REMOVE arrow on the cover. Then rotate
the key so the arrow lines up with the LOCK
arrow. This will prevent the safety key from
coming loose from vibration when the machine
is in use.
Digital Readout
The digital readout (Figure 21) is used for
making incremental spindle height adjustments
where applicable, if multiple shaping/cutting
passes are to be performed on a given work-
piece.
Set the digital readout as follows:
1. Set the desired spindle height for the
workpiece to be cut.
2. Supply power to the machine so the digital
display is lit.
3. Select inch or mm by momentarily
depressing the button on the right.
4. Press the 0" SET button for approximately
two seconds.
The digital display resets to zero, which is your
reference point. When the spindle is raised or
lowered (front handwheel), the change is relative
to this reference.
If this feature is used, the display should be
reset to zero for each new cutting operation.
Figure 21

20
Operations
Overview
Before applying power to the machine, Check the
motor and switch wiring diagrams for proper
voltage connections. Check that all mounting
screws and bolts are tight.
Turn on the motor momentarily to check for proper
rotation. The spindle should rotate counterclock-
wise when looking down on the spindle. Correct as
required.
Run the machine for a short period of time to
ensure that the moving parts are working properly
with no excessive vibration. If a problem develops,
correct it before turning the shaper over for general
use.
Safety Devices
Safety devices such as guards, fixtures, templates
hold-downs, push sticks (Figure 22), feather
boards and power feeders should be used
whenever possible. Figure 22 shows a push stick
which can be easily made from scrap wood.
Note: For the sake of clarity, the shaper guard has
been omitted from most illustrations. All shaper
operations must be done with the proper guard in
place and any other device which insures the
safety of the operator.
Grain Direction Considerations
Plan to shape the workpiece in the same direction
as the grain when possible. Some open grain
woods (such as redwood, fir and oak) will leave a
rough, or slightly splintered edge when cut against
the grain.
Figure 22
Deep cuts require excessive
horsepower and pushing force to control the
cut.
Deep cuts can also cause the wood to splinter or
split and may lead to lost control or personal injury.
Preband shaper the stock whenever possible to
1/16 inch of finished size. When an edge finish is
unsatisfactory, take two or more cuts with the final
cut no more than 1/16 inch deep.
In the case of shaping across the grain, the trailing
board edge will often splinter. To correct this, the
best solution is to make the board 1/4 inch oversize
in width, shape the board, and simply trim off the
excess.
Cutter Rotation
Counterclockwise Setup – With the cutter installed
as shown in Figure 23, feed the workpiece from
right to left.
Figure 23
Clockwise Setup – With the cutter installed as
shown in Figure 24, feed the workpiece from left to
right.
Figure 24