Pr lighting Aqua 580 beam User manual

AQUA 580 BEAM

PR-2569

The user manual contains important information about the safe installation and use of a projector. Please read

andfollowthese instructions carefullyandkeepthemanual in asafeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

SAFETYANDWARNINGS………………………………………………………………………………………

INSTRUCTIONS…………………………………………………………………………………………………

APPEARANCE……………………………………………………………………………………………………

INSTALLATION…………………………………………………………………………………………………

SETUPANDCONFIGURATION…………………………………………………………………………………

OPERATION MENU………………………………………………………………………………………………

DMXPROTOCOL…………………………………………………………………………………………………

SIGNSONTHETOUCHSCREEN…………………………………………………………………………………

10.

11.

12.

ERRORMESSAGE………………………………………………………………………………………………

TECHNICALDATA………………………………………………………………………………………………

CIRCUITDIAGRAM………………………………………………………………………………………………

COMPONENTORDERCODES……………………………………………………………………………………

ACCESSORIES

Thefollowing itemsare suppliedwith theprojectorand pleasecheck:

Name

Quantity

Unit

Remark

Gclamps

Pcs

XLR connector

Set

Maleand female

Safetycord

User manual

Ω clamps

Pcs

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are

subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the

right to change specifications in the course of product improvement. The publishers cannot be held responsible

for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /

or the unit are in good condition before installation and use. Should there be any damage caused by

transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be

assumed by the manufacturer and / or dealer.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from

thedeliverydate butthelight sourceisnotwithinthewarranty.

1.SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety informationhereinafter!

The followingsafetysignsareused intheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking, check if there is transportation damage before using a projector. Should there be any damage

causedbytransportation,consultyourdealer anddonotuseit.

●The manufacturer is not responsible for any loss caused by the user not following the manual or changing a

projector ashe/shelikes.

●Please be noted that the damage causedbychanginga projectoratwill is notwarranted.

● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

●Ifa lampisdamagedordeformsbecauseofheat,itshould bereplaced.(Itappliesonly totraditional lamps)

● Theprojectorisforindoor andoutdooruse,IP66.

● Itcanbeusedinhumidanddustyareas.And it cancontactwaterandothernon-corrosiveliquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmust strictlyfollowtheproceduresinthemanual

●No repairablepartsinthe projectoranddonotopencoversformaintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Donotconnectaprojectorto anytypeofdimmerpack.

●Ifthelamp, lensand screenprotectivecoveroftheaprojectorhaveobviousdamage,i.e., tothe extentthat it

hurtstheperformancelikecracking ordeformation. Pleasestop usingitandreplacethemwith theoriginalparts,

otherwiseitsperformancewillbecompromised.

● For theinstallationlocation of a projector, it shouldn’t be seen in the distance of less than 4 meters for a long

time.

●Before operation, please confirm that all covers (housing) are on and screws tightened. It’s forbidden to use a

projector whilecovers(housing)areoff.

●Keepthelampcleananddo nottouch itwithbarehands.

●While operating it, wear protective items like eye goggles , gloves and etc..

●Any electrical connection must be carried out by a qualified person .

●Beforeinstallation,pleaseconfirmthevoltagesuppliedmatcheswhatisrequired foraprojector.

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If aprojector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefullyor by

pullingthepowercable.

●All power cords must conform to related safety and regulations.

●If a projector is not water and dust proof, while being operated it should not be under rains or in humidity to

avoidshortcircuit.

●Do not switch on and off a projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord

suppliedthroughthe safetycord holesfor safetysupport.

●Beforeany installation,maintenance andcleaning work,pleaseensurea projectorisdisconnected from

powermains.

● While running normally under normal ambient temperature, the temperature of the external surface of the metal

housingofaprojector includingthatofthe heatsinkmayreach170℃at maximum.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean aprojector hassomedefects.

●While it running, don’t touch the metal housing to avoid being burned!

●Do not mount a projector directly on inflammable surface.

●Donotprojectthebeamstraightly oncombustible items andtheminimumdistancebetweenaprojector

andilluminateditemsis5m.

●A projector should be installed with good ventilation and the minimum distance between a projector and a wall

is50cm.Atthesame time,pleaseensurethe fansandair inletsandoutletsareworkable.

●Do not let the front lens under sunlight or other strong light sources at any angle, otherwise the danger of fire

canbecausedbythe focused beambythelensinsideaprojector.

2.INSTRUCTIONS

●CLEANINGANDMAINTENANCE

Under normal running, the protective units of a projector should be inspected regularly like power fuse. If it is burned, please

installa newoneandensureit isthe same ratingastheburnedone.

For a projector with an over-temperature protective unit, please inspect cooling units regularly like cooling fans, heat sink and

othercoolingparts. Pleasecheckifthe fansrun normallyor fansandair inletsareblocked bydust.To keepairinlets/outletsclean,

coolingfansshouldbecleaned every15days.

For projectors with lens, reflectorsand coated filters, the accumulation of oil, smoke and dust on them will compromise the light

output. Cleaning a projector is very necessary to ensure a reliable use. Internal and external lens, flat glass, reflector and coated

filtersneed to be cleanedperiodically tooptimizelightoutput.

Cleaning frequency isto be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. For a projector

with high IP rating, if no damage inside, it is advised to cleanthe surfaces of its housing in principle. Keep lens clean and do not

touch opticalpartswithbarehands.

●Before any maintenance and cleaning, please ensure a project is off the power.

●Only a qualified person is allowed to do maintenance.

●To avoid sunlight or other light penetrating into the head via the front lens, resulting in high temperature internally

causingdamagesto aprojector.Before power-off,please useTiltchannelto move the headand makethe head facing

downward.

● Donotuse alcoholorotherorganicsolventto cleanthe housing to avoiddamage.

● Donotuse anysolventwithchemicalelementsto cleancoated filters.

●LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and

focuslensbelubricated every2 months. Highqualityand hightemperaturelubricant/greaseisadvised..

●TROUBLESHOOTING

PROBLEM

ACTION

A projector doesn’t switch on

Checkthe fuseonthepowersocket.

Checkthelamp.

Thelampisonbuta projector doesn’t respond to

thecontroller

Makesurethatthe fixture’s start address is right

Replace orrepair theXLRsignalcable.

A projector functions intermittently

Makesurethefanisworkingwellorfansandtheirshieldsarenotblocked

Beam appearsdim, Lowinbrightness

Make surethelamp is withinitslifespan

Remove dustorgreasefromthelenses.

Theprojectimageappearstohavea halo

Carefullycleanthelamp,opticallensesandothercomponents.

HeavilyDefective Beam

Checkif lensareingoodcondition(notcracked)

Cleandustorgreaseonthelens.

3. APPEARANCE

4. INSTALLATION

●RIGGING

Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a

projectorwithpowerwhileit islocked.

Head

Arm

Base

Take 2 clamps and the safetycord out fromthe package and mount 2 clamps on the underside of fixture with 2 retainers attached

to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the

underside ofthe base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the

projector is firmlyanchored to avoid vibrationand slipping whilstfunctioning. Always ensurethatthe structurethat youare going

to mountthe projector to issecureandstrong enoughtosupporttheweightofa XR1000Framing.

WARNING:

●The projectorMUSTbe liftedorcarriedbythe HANDLESinsteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connectthe powercordasfollows:

L(live)=brown

E(earth) =yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projectorbeconnected with powerseparatelyso thatthey maybeindividually switchedonandoff.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordancewiththestandardsconcerned.

●Ifanyquestionsaboutthe electricalinstallation,donotcontinuebutconsult aqualifiedelectrician.

Clamp

Safetycord

Warning!

Forsafety, please runthesafetycord

throughitshole.

●DMXCONTROLCONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector)or5pinXLRplugsand sockets.The XLR'sare connected asshowninthefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected inanywayotherthan mentioned in theabove figure. The XR330BWSaccepts digitalcontrolsignals inprotocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthe figurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingand corruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intotheoutputsocketonthe lastprojectorinthechain.Theconnectionsare illustrated below.

DMX Teminator

DMX

Controller

Input Output Input Output Input

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

● ALIGNMENT/INSTALLATION/REPLACEMENTOFALAMP

Please hold the projector well before adjustment/installation/replacement oflamp. As shown in figure1,remove fan cover ofthe head

andheatsink.

Removal/Installationoflampasshowninfigure2

Adjustthelamp asshowninfigure3

Beforetheremovalofthelamp, unplug the lamp wires.And pluglamp wires after anewone is in.

●Don’t touch the internal surface of the reflector and the burner ofthe lamp with bare hands so as not to impair the

beam output. There is aprotruding metal wire in the lamp, while installation do not damage it. Hold the lamp body

well before its removal. It’s forbidden touseforceontheceramicstand,otherwiseitwill loosenor fall off.

●Pleaseread "Instructions" enclosedwiththe lamp

●While adjusting thelamp, it is forbidden to carry out the functions not associated with lamp adjustment.

Figure1:loosen4 screwsofthefancoveroftheheadbefore removingit.Thenloosenthe screwsofheat sinkandremove it

andthefan.

Figure2:Unplugthelampwires,pushtheupperclippingplatetowardthespringwith force,butpushthelamp inthe

opposite directiontill itisofftheplate,thentakethelampout obliquely.Thesameappliestoitsinstallation.

Figure3:Afterthereplacementofthelamp,pleaseensurefirstthelampisclippedwellbeforeplugginglampwires.Turnthe

lamp on and adjust the lamp’s positiontothe middle.Afterthat,installtheheatsink,fanandfancover.

1. After theprojectoris powered on, disablethe following functioninthemenu: services-factory mode-lampfansensor,thenshut

itfrompower

2. Loosenthe4screws ofthefancoverand removeit.

3. Loosen4 screwsofthefanplate,remove the fanand the clumpweight,loosen10screwsoftheheat sink andremove it.

4. Pushtheupperclippingplateofthelamptowardsthespring,andatthesame timepusthelamptowardstheopposite tillitisoff

theplateandremoveitobliquely,

5. Theinstallationofthelampisthesame asitsremoval

6. Checkifthelamp wiresarepluggedwell,thenturnonthelampfor adjustment

7. After theadjustmentofthe lamp,activate the followingfunctioninthe menu:services-factorymode-lamp fansensor.Thenshut

itfromthepower

8. Check if the sealsare goodor not. Ifnot, replace them withgood ones. If no, installthe heatsink, fan and fancover in the

oppositesequencesastheremoval.

9. After installation,powerit on.Theprojectorwillexecute the totalreset.After that,theprojectorcanbeused normally.

●GOBOREPLACEMENT

DANGER!

Beforereplacementofgobos,the projectormust beoffthepower.

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

To browse through or change the projector ’s settings, press ENTER key for more than 3s(press ENTER key after power on) to

unlock the screen , then press UP/DOWN key to enter the projector ’s function menus. Each main menu has its sub-menus. And

eachmenustandsforspecial function. Forthedetails, pleaseseethefollowing6th point ”Operation Menu”.:

1. At the page to set the fixture’s functions, press UP or DOWN keyto selectthefunctionsdesired.

2. While menu operations, the FUNC keyto escape, and ENTER key is used to confirm. Press ENTER key to save the changes

orenterintothe sub menus.Press UP or DOWN keyto changethenumbers(minusorplus).

Press FUNC keyto go to the upplermenu. If no keyis pushed, thesystemwillgo back to initial status automatically.

●DMX STARTADDRESS

Each projector mustbegivena DMX start address so that the correct projectorresponds to the correct control signals.ThisDMXstart

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 3DMX modes. There are standard mode ,short mode and extended mode. For example standard mode

has 26 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 027, No. 3 projector’s address 053,No. 4

projector’s address 079, andso on.

Switch on the Projector . Press ENTER key more than 3 seconds to unlock panel, then press UP or DOWN key to enter into the

Rotating gobo wheel

Rotator

Gobo

Gobo spring

Rotator

Replacement of the Gobos:

Open the chamber cover after loosening 4 screws.

Select the rotator for replacement of gobo. Push

the rotator at the opposite side of its gear till it is

off the holder of the rotating gobo wheel. Remove

the rotator gently . After replacement of the gobo,

place the rotator into the wheel and ensure it is in

the right position and not loose.

fixture’s operation menus.

Select DMXAddressiconand pressENTERkeyonthedisplayandselectDMXaddressat the2nd levelmenu fortheaddresssetting.

Press UP or DOWN keyfor the DMXaddressdesired.

Press ENTER keytoconfirm.

Press the FUNC keytogobacktothe upperlevelmenu.

●DMXWIRELESSCONTROL

Theprojectorhaswirelesscontrol functionwith wirelessreceiver moduleandantenna forremote control.

Thesetupofitisbelow:

1. Press ENTER for more than 3s to unlock the control panel, then press UP or DOWN key to enter into the operation

menu and select “Config Settings”.

2. Select “Wireless Only” from the menu of “Signal Select”.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Un-link Wireless under the upper level menu of Config Settigns ,then the fixtureis unlinked

with the wireless transmitter.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR controlcable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

besetaccordingly.

AfterPoweredon,the group willruninMaster/Slave Mode

Input Output

Master Slave Slave

Input Output Input

DMX

Controller

DMX Teminator

6.OPERATIONMENU

1st

LEVEL

2ndLEVEL

3rdLEVEL

4thLEVEL

5thLEVEL

Address

DMXAddress

1-490(ShortMode)

1-486(StandardMode)

1-482(ExtendMode)

IP Address

DefaultIPAddress

2.X.X.X /10.X.X.X

CustomIPAddress

X.X.X.X

SubNetMask

X.X.X.X

ArtNetUniverse

0-255

Reset

Total Reset

ReallyReset?

Confirmor Cancel

Pan&TiltReset

ReallyReset?

Confirmor Cancel

ColourSystemReset

ReallyReset?

Confirmor Cancel

GoboReset

ReallyReset?

Confirmor Cancel

Dimmer/StrobeReset

ReallyReset?

Confirmor Cancel

Fo.Fr.Pr.Reset

ReallyReset?

Confirmor Cancel

Config

Settings

DMXChannel Mode

Short Mode22CH

StandardMode26CH

ExtendedMode 30CH

ViewSelectedMode

Ch.01Strobe

Ch.02Dimmer

......

Ch.26Power/SpecialFan

Lamp Control

OFF/ ON

On ByPower On

OFF/ ON

ControlByDMX

OFF/ ON

ECOPower

OFF/ ON

SignalSelect

XLROnly

XLRFirst

WirelessOnly

WirelessFirst

WirelessIn/XLR Out

ARTNETOnly

ARTNETIn/XLROut

LossofDMX

Normaltimeout

Hold LastValue

DisplayConfig

DisplayMode

OffAfterDelay

OnAlways

DisplayInvert

InvertOFF

InvertON

InvertAuto

LanguageSetting

English\Chinese

TemperatureUnit

CelsiusDegree

FahrenheitDegree

Un-LinkWireless

Really Un-Link?

Confirmor Cancel

Factory Defaults

RestoreDefaults?

Confirmor Cancel

Option

Settings

Pan/TiltSettings

PanDMX Invert

OFF/ ON

TiltDMXInvert

OFF/ON

PanTiltSwap

OFF/ ON

XYFeedback

OFF/ ON

Pan/Tilt mode

Speed/Time

Note: "Speed Mode"means

PanandTiltwillmovefrom

PointAtoPointBattheir

respectivemaximum

speeds."TimeMode" means

bothPanand Tilt willarriveat

designatedpointat thesame

time. It'sadvised TimeModebe

used iftheprojector runscircles

orinobliquelines.

InvertSettings

DimmerInvert

OFF/ ON

ZOOM Invert

OFF/ ON

ViewDMXValues

Channel Value

Strobe XXX

Dimmer XXX

DimmerFine XXX

CYMMacro XXX

Cyan XXX

Information

Yellow XXX

Magenta XXX

CTO XXX

ColorWheel XXX

Color WheelFine XXX

Fixed GoboWheelXXX

Rot. GoboWheel1 XXX

Rot. GoboRotationXXX

Rot. GoboRotationF.XXX

Prism1 XXX

Prism1Rotation XXX

Prism2 XXX

Prism2Rotation XXX

Focus XXX

FocusFine XXX

Pan XXX

PanFine XXX

Tilt XXX

Tilt Fine XXX

Pan/TiltSpeed&TimeXXX

Power/Special Fun.XXX

Lamp Hours

Lamp Hous=XXX H

Reset Lamp Hours

Total Hours

TotalHous××××H

Temperature

DisplayBoard=×××C

Panboard=×××C

Tiltboard=×××C

DriverBoard1=×××C

DriverBoard2=×××C

HeadSensor=×××C

SoftwareVersion

PCBBoard Sys Boot

DisplayBoard xxx xxx

Panboard xxx xxx

Tiltboard xxx xxx

DriverBoard1 xxx xxx

DriverBoard2 xxx xxx

ElectronicSN

XXXXXX

RDMDeviceLabel

AQUA580 Beam

ANSIE1.20RDM

FanStatus

Fan Speed RSpeed

Lamp Fan1 xxx xxxx

Lamp Fan2 xxx xxxx

HeadFan xxx xxxx

Gobo Fan xxx xxxx

Lamp TFan xxx xxxx

LampRFan xxx xxxx

AccelerationSensor

X Axis:XXX

YAxis:XXX

ZAxis:XXX

Position:XXX

Lamp FanError

Fan Error

LampFan1 xxx

LampFan2 xxx

HeadFan xxx

GoboFan xxx

Lamp TFan xxx

LampRFan xxx

ManualEffectControl

StrobeXXX

DimmerXXX

DimmerFine XXX

Service

CYMMacroXXX

Cyan XXX

Cyan FineXXX

YellowXXX

YellowFine XXX

MagentaXXX

MagentaFineXXX

CTOXXX

CTOFine

ColorWheelXXX

ColorWheelFineXXX

Fixed GoboWheel XXX

Rot. GoboWheel XXX

Rot. GoboRotation XXX

Rot. Gobo RotationF.XXX

Prism1XXX

Prism1RotationXXX

Prism2XXX

Prism2RotationXXX

FocusXXX

FocusFineXXX

PanXXX

PanFineXXX

TiltXXX

TiltFineXXX

Pan/TiltSpeed &TimeXXX

FactoryMode

XXX

…

Operation

Mode

DMXMode

ChangeOperationMode?

Confirmor Cancel

MasterMode

PresetMemory

ChangeOperationMode?

Confirmor Cancel

UserMemory1

ChangeOperationMode?

Confirmor Cancel

UserMemory2

ChangeOperationMode?

Confirmor Cancel

Stand-AloneMode

PresetMemory

ChangeOperationMode?

Confirmor Cancel

UserMemory1

ChangeOperationMode?

Confirmor Cancel

UserMemory2

ChangeOperationMode?

Confirmor Cancel

StaticScene

ChangeOperationMode?

Confirmor Cancel

Edit UserMemory1

Edit UserMemory2

（1~200Scenes）

SceneXX

（1~200Scenes）

StrobeXXX

DimmerXXX

DimmerFine XXX

CYMMacroXXX

CyanXXX

Cyan FineXXX

YellowXXX

YellowFine XXX

MagentaXXX

User

Memories

Edit UserMemory

MagentaFineXXX

CTO XXX

CTOFine XXX

ColorWheelXXX

ColorWheelFineXXX

Fixed GoboWheel XXX

Rot. GoboWheel XXX

Rot. GoboRotation XXX

Rot. GoboRotationF.XXX

Prism1XXX

Prism1RotationXXX

Prism2XXX

Prism2RotationXXX

FocusXXX

FocusFineXXX

PanXXX

PanFineXXX

TiltXXX

TiltFineXXX

Pan&TiltSpeed &TimeXXX

FadeTime.XXX

Hold TimeXXX

DelayunitXXX

LinktoStepXXX

Edit Static Scene

StrobeXXX

DimmerXXX

DimmerFine XXX

CYMMacroXXX

Cyan XXX

Cyan FineXXX

YellowXXX

YellowFine XXX

MagentaXXX

MagentaFineXXX

CTO XXX

CTOFine XXX

ColorWheelXXX

ColorWheelFineXXX

Fixed GoboWheel XXX

Rot. GoboWheel XXX

Rot. GoboRotation XXX

Rot. GoboRotationF.XXX

Prism1XXX

Prism1RotationXXX

Prism2XXX

Prism2RotationXXX

FocusXXX

FocusFineXXX

PanXXX

PanFineXXX

TiltXXX

TiltFineXXX

Pan&TiltSpeed &Time

XXX

InitUserMemory

Reset UserMemory1

Reset UserMemory?

Confirmor Cancel

Reset UserMemory2

Reset UserMemory?

Confirmor Cancel

Reset Static Scene

Reset Static Scene?

Confirmor Cancel

Remarks:Lampfansensorisonlyusedduringlampadjustment

Open: the lamp is affected by the lamp fan. If the lamp fan fails, the lamp won’t be on.

Close: the lamp is not affected bythe lamp fan. Even if the lamp fan is not installed, the lamp will be on, but

PanandTiltarewithoutforce .

“Close” status is used only in emergency. If the lamp fan won’t run for long, it will cause harm to the

lamp.

After lamp adjustment, set the “lamp fan sensor as “Open” and activate total reset.

7.DMXPROTOCOL

Short

mode

Standard

mode

Extended

Mode

FUNCTION

DMX

DESCRIPTION

Strobe

000-010

011-025

Open

026-225

Strobe speed fromslowtofast

226-246

Randomstrobefromslowtofast

247-255

Open

Dimmer

000

001-255

Linear dimming（0-100%）

DimmerFine

000-255

Dimmerin16bit

CYMMacro

000-016

White

017-035

Yellow+ Magenta=Red

036-054

Yellow

055-073

Yellow+Cyan=Green

074-092

Cyan

093-111

Cyan+ Magenta= purple

112-128

Magenta

129-255

CYMcolormixingfromslowto fast

Cyan

000-255

Cyan(linear 0~100%)

CyanFine

000-255

Cyan in16Bit

Yellow

000-255

Yellow(linear0~100%)

YellowFine

000-255

Yellowin16Bit

Magenta

000-255

Magenta (linear0~100%)

Magenta Fine

000-255

Magenta in16Bit

CTO

000-005

006-024

Diffuser

025-255

Linear CTO

CTO Fine

000-255

CTO in 16bit

ColorWheel

000-063

Indexing(0-360degrees)

064-068

Color1(Red)

069-073

Color2(LightGreen)

074-078

Color3(Blue)

079-083

Color4(Cyan)

084-088

Color5(Yellow)

089-093

Color6(Magenta)

094-098

Color7(Orange)

099-103

Color8(Green)

104-108

Color9(DarkBlue)

109-113

Color10(UV)

114-118

Color11(LightYellow)

119-123

Color12(DarkYellow)

124-127

White

128-191

Rotation,Clockwisefromslowtofast

192-255

Rotation,Anti-clockwisefromfasttoslow

ColorWheelFine

0000-255

ColorWheelin16Bit

Fixed Gobo

Wheel

0-8

White

9-15

Gobo1

16-22

Gobo2

23-29

Gobo3

30-36

Gobo4

37-43

Gobo5

44-50

Gobo6

51-59

Gobo7

58-64

Gobo8

65-71

Gobo9

72-78

Gobo10

79-85

Gobo11

86-92

Gobo12

93-99

Gobo13

100-106

Gobo14

107-113

Gobo15

114-120

Gobo16

121-124

Gobo17

125-127

Gobo18

128-157

Clockwiserotation fromslowtofast

158-187

AntiClockwiserotation fromslow to fast

188-191

Shakeeffect 1fromslowto fast

192-195

Shakeeffect 2fromslow to fast

196-199

Shakeeffect 3fromslowto fast

200-203

Shakeeffect 4fromslow to fast

204-207

Shakeeffect 5fromslowto fast

208-211

Shakeeffect 6fromslow to fast

212-215

Shakeeffect 7fromslowto fast

216-219

Shakeeffect 8fromslow tofast

220-223

Shakeeffect 9fromslow to fast

224-227

Shakeeffect 10fromslowto fast

228-231

Shakeeffect 11fromslowtofast

232-235

Shakeeffect 12fromslowto fast

236-239

Shakeeffect 3fromslow to fast

240-243

Shakeeffect14fromslowtofast

244-247

Shakeeffect 15fromslowto fast

248-251

Shakeeffect 16fromslowto fast

252-255

Shakeeffect 17fromslowto fast

RotatingGobo

Wheell

000-015

White

016-031

Gobo1

032-047

Gobo2

048-063

Gobo3

064-079

Gobo4

080-095

Gobo5

096-111

Gobo6

112-127

Gobo7

128-156

Rotation （clockwiseFromslowtoFast）

157-185

ReverseRotation（anti-clockwise From slow to

Fast）

186-195

ShakeofGobo1fromslowtofast

196-205

ShakeofGobo2fromslow tofast

206-215

ShakeofGobo3fromslow tofast

216-225

ShakeofGobo4fromslow tofast

226-235

ShakeofGobo5fromslow tofast

236-245

ShakeofGobo6fromslow tofast

246-255

ShakeofGobo7fromslow tofast

Gobo Rotation

000-128

GoboIndexing(0~540degrees)

129-188

Rotation （Clockwise FromslowtoFast）

189-195

Stop

196-255

Rotation （Anti-ClockwiseFromslowtoFast）

Gobo Rotation

Fine

000-255

GoboRotation in16Bit

Prism1

000-016

Open

017-127

Prism1

128-255

Prism2

Prism1 Rotation

000-127

PrismIndexing

128

Stop

129-191

Rotation(Clockwisefromslowtofast)

192

Stop

193-255

Rotation(Anti-Clockwisefromslowtofast)

Prism2

000-016

White

017-127

Prism3

128-255

Frostin

Prism2 Rotation

000-127

Prism2 Indexing

128

Stop

129-191

Rotation(Clockwisefromslowtofast)

192

Stop

193-255

Rotation(Anti-Clockwisefromslowtofast)

Focus

000-255

Linear focus

FocusFine

000-255

Focusin16bitprecision

Pan

000-255

Pan(0°~540°)

PanFine

000-255

Panin16bit

Tilt

000-255

Tilt(0°~270°)

Tilt Fine

000-255

Tilt in16bit

Pan &TiltSpeeds

000-255

Pan&TiltSpeed fromFastto Slow

Control

000-019

Reserved

Keep in the DMX range for more than 5S to activate the following

functions.Ifpower-off, thefollowingareinvalid.

020-024

Graphic DisplayOn

025-029

Graphic DisplayOff

030-034

Reserved

035-039

Lamp ECOPower

040-044

Lamp FullPower

045-089

Reserved

090-094

Pan&TiltSpeedMode

095-099

Pan&TiltTimeMode

100-129

Reserved

130-139

Lamp On

140-149

Pan&TiltReset

150-159

ColorSystemReset

160-169

Gobo Wheel Reset

170-179

Dimmer/ShutterReset

180-189

Zoom/Frost/Focus/PrismReset

190-199

Reserved

200-209

Total Reset

210-229

Reserved

230-239

Lamp Off

240-255

Reserved

1. The projector can’t be turned on within 1 minute after the lamp-off.

2.Fanerrorcancauselamp-off.

8.SIGNSONTHETOUCHSCREEN

Lampcomtrol

OptionSettings

Chinese-English

Information

Error messages

Service

Address

OperationMode

Reset

UserMemories

ConfigSettings

9.ERRORMESSAGES

Thesystemcandetectsomeerrorsduringthereset,if displayed,touch to viewtheerror.

The error messagesare as follows:

Name

Type

Correction

Pan

Timeout/magnetSensor/Encoder