Prestige APSPS1 User manual

5A
15A
1 Red Baery 12V Input (+)
2 Yellow Ignion Input (+)
3 Black Ground Input (-)
4 White/Red Parking Light (87) Input
5 White Parking Light (30) Output
6 Black/Yellow Starter Kill (87A) Input
7 Black/Yellow Starter Kill (30) Output
8 Purple/White Closed Loop Trigger
9 Purple/White Closed Loop Trigger
10 Lt. Green  Input (-)
11 Dk. Blue Aux Ch.3 Output
12 White/Black Siren / Horn Output (+)
13 Red/Blue LED Output
14 Black/White Antenna
Main Harness
APSPS1 System Layout
ARM
DISARM
ARM
DISARM
Replacement Part # PEPS2 Replacement Part # 4360926
Replacement Part # 4360924

Alarm Override Procedures
This system includes two (2) Alarm Override methods. The override
method is selected in Feature Bank 2, Feature 9.
Default Override Procedure
1. Cycle the ignion to the ON posion 5x, ending in ON. The
system will illuminate the LED Solid.
2. Cycle the ignion OFF/ON.
The system is now silenced and disarmed. To rearm the system, press
the ARM buon on the remote control.
Custom Code Override Procedure (Default Code - 1)
1. Cycle the ignion to the ON posion 5x, ending in ON. The
system will illuminate the LED on Solid.
2. Cycle the ignion OFF, the LED will begin to ash.
3. When the LED ashes the number of mes that matches your
custom code, cycle the ignion to the ON posion.
The system is now silenced and disarmed. If the ignion is not cycled
ON at the correct me, the user must wait ve (5) seconds before
aempng another override.
Custom Code Override Programming
1. Cycle the ignion to the ON posion 8x, ending in ON. The
LED will illuminate for two (2) seconds to conrm custom code
programming
2. Turn the ignion OFF. The LED will begin to ash to conrm the
original code (Default Code - 1)
3. Turn the ignion ON when the LED ashes the original code. If
correct the system will beep 1x to conrm.
4. Cycle the ignion OFF, the LED will begin to ash. When the
LED reaches the number of the desired custom code, cycle the
ignion ON to conrm.
5. Cycle the ignion OFF. The LED will ash to conrm the new
custom code.
Remote Control Programing
This system includes two (2) programmed remote controls. If
addional remote control programming is required, use the following
steps:
1. Cycle the ignion to the ON posion 5x, ending in ON. The
system will beep 1x to indicate Feature Bank 1, Remote Control
Programming.
2. Press the ARM buon on each remote control that requires
programming. The system will beep to indicated the remote
control is programmed.
3. Cycle the ignion to the OFF posion.
Note: The system can store up to four (4) remote controls in its
memory bank. Each remote control programmed aer four (4) will
automacally delete the oldest remote control.
Feature Programming
The system must be programmed using the ignion switch and
remote control. To program features:
1. Cycle the ignion to the ON posion 5x, ending in ON. The
system will beep 1x to indicate Feature Bank 1, Remote Control
Programming.
2. Cycle the ignion OFF/ON 1x. They system will beep 2x to
indicate Feature Bank 2.
3. Press the ARM buon on any remote control to cycle through
the features. The LED will ash to indicate the feature number.
4. Press the DISARM buon to change the feature opon. The
system will beep to indicate the opon selected.
5. Repeat Steps 3 and 4 unl all desired features have been
programmed.
6. Cycle the ignion to the OFF posion to exit Feature
programming.
Note: To default all features, follow steps one (1) to three (3) above
to advance to Feature 10, then press Disarm.
Security Nocaons
If the security system as been triggered the system will provide
feedback to the user to indicate the trigger zone. When the
user presses the DISARM buon the system will beep 4x and
ash the parking lights to display the trigger zone.
Adjusng the Shock or Tilt Sensor
The Shock and Tilt sensor adjustments are made using the feature bank
programming method.
Feature 3 - Tilt Sensor Adjustment
Feature 7 - Shock Sensor Adjustment
To test sensivity, strike the vehicle with an open palm. Adjust the
sensivity using Feature 7.
APSPS1
For Complete Installaon Guide and Technical Support
Please Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
Quick Installaon Guide
4 Tilt / Shock
5 Addi�onal Sensor
6 Loop Input
7 Igni�on Input
1 Chirp 2 Chirp
3 Chirp 4 Chirp 5 Chirp 6 Chirp 7 Chirp 8 Chirp
1 Auto Arming OFF ON
2 Anti Hi-Jacking OFF ON
3 Tilt Sensor Level 1 5
15 30
4 Silent Mode OFF ON
5 Security Notification Siren Horn
6 Parking Light Output ON OFF
7 Shock Sensor Level 12
34 5 6 7 8
8 Aux Ch.3 Output 1sec Pulse Latch ON/OFF
Latch Until IGN
9 Override Method Default Custom Code
10 Default All Features
OFF
ON
Feature Bank 2
Features
Options