Pride Mobility Go-Chair User manual

Product Serial #
USA
182 Susquehanna Avenue
Exeter, PA 18643-2694
Canada
5096 South Service Road
Beamsville, Ontario L0R 1B3
UK
32 Wedgwood Road
Bicester, Oxfordshire OX26 4UL
www.pridemobility.co.uk
Australia
20-24 Apollo Drive
Hallam, Victoria 3803
www.pridemobility.com.au
New Zealand
38 Lansford Crescent
Avondale
Auckland, New Zealand 1007
www.pridemobility.co.nz
Italy
Via del Progresso, ang. Via del Lavoro
Loc. Prato della Corte
00065 Fiano Romano (RM)
www.pride-italia.it
B.V.
Castricummer Werf 26
1901 RW Castricum
The Netherlands
www.pride-mobility.nl
www.pridemobility.com
Owner’s Manual

Safety Guidelines
Authorized Pride Provider:
Address:
Telephone:
Purchase Date:
WARNING! An authorized Pride Provider or a qualified technician must perform the initial
setup of this travel chair and must perform all of the procedures in this manual.
The symbols below are used throughout this owner’s manual and on the Go-Chair to identify warnings and important
information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow
designated procedures can cause either personal injury, component damage, or
malfunction. On the product, this icon is represented as a black symbol on a yellow
triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause personal injury and/or equipment damage. On the product,
this icon is represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at
any time or in any circumstances. Performing a prohibited action can cause personal
injury and/or equipment damage. On the product, this icon is represented as a black
symbol with a red circle and red slash.
INTENDED USE
The intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seated position
that have the capacity of operating a powered wheelchair.
REGARDING DEVICES FOR PRESCRIPTION USE
CAUTION! Federal law restricts this device to sale by or on the order of a physician or
other certified personnel licensed by the law of the State (US only) or region in which
this personnel practices to use or order the use of the device.
Quick Reference Information
Copyright © 2016
INFMANU4750/Rev A/June 2016
NOTE: This owner’s manual is compiled from the latest specifications and product information available at
the time of publication. We reserve the right to make changes as they become necessary. Any changes to
our products may cause slight variations between the illustrations and explanations in this manual and the
product you have purchased. The latest/current version of this manual is available on our website.
NOTE: This product is compliant with WEEE, RoHS, and REACH directives and requirements.
NOTE: This product meets IPX4 classification (IEC 60529).
NOTE: This product and its components are not made with natural rubber latex. Consult with the
manufacturer regarding any after-market accessories.

3
Introduction..............................................................................................................................................4
Safety........................................................................................................................................................5
Your Go-Chair...........................................................................................................................................7
Assembly/Disassembly..........................................................................................................................10
Comfort Adjustments............................................................................................................................13
Batteries and Charging..........................................................................................................................17
Care and Maintenance...........................................................................................................................23
Table of Contents

4
Safety
WELCOME to Pride Mobility Products (Pride). The travel chair you have purchased combines state-of-
the-art components with safety, comfort, and styling in mind. We are confident that these design features
will provide you with the conveniences you expect during your daily activities. Once you understand how
to safely operate and care for your travel chair, it should give you years of trouble free operation and
service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your
travel chair for the first time. You must also read all instructions, warnings, and notes contained in any
supplemental instructional booklets for the controller that accompanied your travel chair before initial
operation. Your safety depends upon you, as well as your provider, caretaker, or healthcare professional
in using good judgment.
If there is any information in this manual which you do not understand, or if you require additional assistance
for setup or operation, please contact your authorized Pride Provider. Failure to follow the instructions
in this manual and those located on your travel chair can lead to personal injury and/or damage
to the travel chair, including voiding the warranty.
Purchaser’s Agreement
By accepting delivery of this product, you promise that you will not change, alter, or modify this product
or remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail,
refuse, or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the
safe use of this product.
Shipping and Delivery
Before using your travel chair, make sure your delivery is complete as some components may be
individually packaged. If you do not receive a complete delivery, please contact your authorized Pride
Provider immediately. Where damage has occurred during transport, either to the packaging or content,
please contact the delivery company responsible.
NOTE: If you ever lose or misplace your copy of this manual, contact us and we will be glad to
send you a new one immediately.
Introduction

5
Product safety symbols
The symbols below are used on the travel chair to identify warnings, mandatory actions, and prohibited
actions. It is very important for you to read and understand them completely.
NOTE: There are more warnings identified and explained in the Consumer Safety Guide that is
included with your travel chair. Please become familiar with all the warnings and safety information
found in the Consumer Safety Guide.
Read and follow the information in the owner’s manual.
Locked and in drive mode.
Place unit on level ground and stand to one side when changing from drive mode
to freewheel mode or freewheel mode to drive mode.
Unlocked and in freewheel mode.
Indicates travel chair securement points.
Class II Equipment.
Manufactured in.
Travel Chair information label.
Safety

6
General Guidelines
MANDATORY! Do not operate your new Go-Chair for the first time without completely
reading and understanding this owner’s manual.
Your Go-Chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides
an extensive variety of products to best fit the individual needs of the Go-Chair user. Please be aware that
the final selection and purchasing decision regarding the type of travel chair to be used is the responsi-
bility of the Go-Chair user, who is capable of making such a decision, and his/her healthcare professional
(i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted
the Go-Chair to the user and has assisted the prescribing healthcare professional and/or the authorized
Pride Provider in the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the Go-Chair user will need to
practice operating the Go-Chair in the presence of a trained attendant. A trained attendant can be defined
as a family member or care professional specially trained in assisting a Go-Chair user in various daily
living activities.
As you begin using your Go-Chair during daily activities, you will probably encounter situations in which
you will need some practice. Simply take your time and you will soon be in full and confident control as
you maneuver through doorways, on and off of lifts, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed
to operating your Go-Chair safely.
Pre-Ride Safety Check
Get to know the feel of your Go-Chair and its capabilities. Pride recommends that you perform a safety
check before each use to make sure your Go-Chair operates smoothly and safely.
Perform the following inspections prior to using your Go-Chair:
Check all electrical connections. Make sure they are tight and not corroded.
Check all controller connections to the power base. Make sure they are secured properly.
Check the brakes. See “Care and Maintenance.”
Check battery charge. See “Batteries and Charging.”
Ensure the manual freewheel levers are in drive mode before sitting on the travel chair.
NOTE: If you discover a problem, contact your authorized Pride Provider for assistance.

7
The Go-Chair
The Go-Chair has two main assemblies: the seat assembly and the power base assembly. See figure 1.
Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly
includes the two motors, two drive wheels, two caster wheels, two anti-tip wheels, two batteries, and a foot
platform. See figures 1 and 2.
Figure 1. The Go-Chair
Your Go-Chair
Identification Key
1. Seatback
2. Armrests
3. Joystick
4. Controller
5. Seat Base
6. Seat Release Lever
7. Foot Platform
8. Caster Wheel
9. Drive Wheel
10. Power Base Assembly
11. Seat Assembly
2
3
4
5
7
8
9
10
11
6
1

8
1
3
4
5
6
7
2
8
Figure 2. The Go-Chair Power Base
Electrical Components
The electrical components are located on the power base. The main circuit breaker is located on the front
of the battery box. The controller connector is located on the back of the power base. See figure 2.
Controller Connector: This is where the controller connects to the power base. Each controller uses a
different type of cable. Regardless of which type of controller is used, the cable must be secured to the
assembly and not allowed to drag on the floor.
Battery Box Charger Port: This enables you to charge the batteries when the battery box is removed
from the power base. See “Batteries and Charging.”
Main Circuit Breaker: The main circuit breaker is a safety feature built into your Go-Chair. When the
batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips
to prevent damage to the motors and the electronics. If the circuit trips, allow your Go-Chair to “rest” for
approximately one minute. Next, push in the circuit breaker button, turn on the controller, and continue
normal operation. If the main circuit breaker continues to trip repeatedly, contact an authorized Pride
Provider.
Identification Key
1. Manual Freewheel Levers
2. Seat post
3. Battery Box
4. Battery Charger Port Location
5. Circuit Breaker
6. Front Section
7. Rear Section
8. Controller Connector Location

9
Manual Freewheel Levers
For your convenience, your Go-Chair has a manual freewheel lever on each motor. Manual freewheel
levers enable you to disable the drive system in order to maneuver the chair manually.
WARNING! Do not use the travel chair while the drive motors are disengaged!
Do not disengage the drive motors when the travel chair is on an incline or
decline, as the unit could roll on its own! Only engage the freewheel mode
when on a level surface.
WARNING! It is important to remember that when your Go-Chair is in freewheel
mode, the braking system is disengaged.
NOTE: Pride strongly recommends you do not charge your batteries while in freewheel mode.
NOTE:You must turn off the power before disabling the drive systems; otherwise, you may get an
error code on the controller. To clear this code, turn off the controller and place the Go-Chair in
drive mode. Then turn on the controller. The error message should be cleared. If not, contact an
authorized Pride Provider.
To engage or disengage the drive system:
1. Locate the levers on the rear section of the power base. See figure 3.
2. Push the two levers toward the front of the power chair to engage the drive motors (drive mode).
3. Pull the two levers toward the rear of the power chair to disengage the drive motors (freewheel mode).
If a lever is difficult to move in either direction, rock your travel chair back and forth slightly. The lever
should then move to the desired position.
WARNING! Do not use the freewheel lever handles as tie-down points to secure this
product.
Anti-Tip Wheels
The anti-tip wheels are an integral and important safety feature of your Go-Chair. They are bolted to the
frame at the rear of the chair. See figure 3.
PROHIBITED! Do not remove the anti-tip wheels or modify your travel chair in any way
that is not authorized by Pride.
Figure 3. Back of Power Base
Freewheel Mode (Drive Disengaged)
Drive Mode (Drive Engaged)
1
2
1. Manual Freewheel Levers
2. Anti-tip Wheels
Identification Key

10
Initial Assembly
Your Go-Chair may require some assembly either before initial use or after transportation. It may also
require disassembly to make some comfort adjustments. Figure 4 details those parts of the Go-Chair
that are designed to be disassembled and assembled by an end user or by a qualified caregiver before
using the product or making comfort adjustments. There are two hex keys provided for use with controller
installation and adjustment and foot platform adjustment.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the travel chair
must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause
damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are
available at local hardware stores or through your authorized Pride Provider.
1
3
4
6
7
2
8
5
Figure 4. Go-Chair Assembly View
Assembly/Disassembly
Identification Key
1. Seat
2. Under-seat Storage
3. Battery Box
4. Foot Platform
5. Under-seat Storage Hinge
6. Seat Post
7. Controller
8. Armrest

11
Seat Installation
It may be necessary to install the seat either prior to initial
operation or after transporting your Go-Chair.The seat is
attached to the power base by a height-adjustable seat
post.
WARNING! Do not pick up the seat frame
by the armrests. They are free to pivot,
and you may lose control of the seat if
they do so.
To install the seat:
1. Adjust the seat height if necessary. See “Comfort
Adjustments.”
2. Set the seat onto the seat post. See figure 5.
3. Installunder-seatstorage.See“Comfort Adjustments.”
4. Install the controller into the armrest, and tighten the
setscrew under the armrest.
5. Route the controller harness to the rear of the power
base.
6. Plug the controller harness connector into the power
base.
7. Secure the controller harness to the armrest with
wire ties. See figure 5.
MANDATORY! Prevent controller harness
damage! Avoid routing the controller
harness on the outside of the armrest
pad. Route the harness under the armrest
or toward the inside of the armrest pad.
Use correct tie-down points for the
controller harness to prevent the harness
from getting caught in the drive tires,
pinched in the seat frame, or damaged
when passing through doorways.
Disassembly
The Go-Chair disassembles into five components: the
seat, the under-seat storage bin, the battery box, the
rear section of the power base, and the front section of
the power base. See figure 6.
To disassemble the Go-Chair:
1. Turn off the power to the controller.
2. Place the Go-Chair in drive mode, if not in drive mode
already. See “Your Go-Chair.”
3. Unplug the controller from power base.
4. Remove under-seat storage. See “Comfort
Adjustments.”
5. Remove the seat by lifting it straight up and off of the
Go-Chair. If you encounter resistance when removing
the seat, disengage the seat release lever and swivel
the seat back and forth while lifting up on the seat.
6. Grasp the battery box handle and lift up to disengage
the box from the power base, then tilt the box foward
slightly and pull it away from the power base.
7. Disconnect two halves using the frame release lever.
1
2
Figure 5. Seat Installation
1
3
4
5
2
6
Figure 6. Go-Chair Components
Identification Key
Identification Key
1. Seat
2. Seat Release Lever
3. Under Seat Storage
4. Front Section
5. Rear Section
6. Battery Box
1. Wire Tie
2. Controller Connector

12
3
2
1
Assembly
1. Use the frame release lever to lift the front section as you align the frame hooks of the front section
with the lower frame tube of the rear section. See figure 7.
2. Once the frame hooks are over the lower frame tube, lower the front section and pivot the rear section
simultaneously. This will engage the frame lock-up automatically. See figure 7.
3. Reinstall the battery pack
4. Reinstall the seat and rotate it until it is secured into place.
5. Plug the controller into the power base.
6. Reinstall under-seat storage.
Identification Key
1. Frame Release Lever
2. Frame Hooks
3. Lower Frame Tube
Figure 7. Go-Chair Assembly

13
Comfort Adjustments
After becoming familiar with your travel chair’s operation, you may find the need to make some adjustments
to increase your comfort, such as seat height, armrest width, foot platform depth, and controller position.
Use the steps below to make comfort adjustments.
WARNING! The center of gravity of your travel chair was factory set to a position that
meets the needs of the demographic majority of users. Your authorized Pride Provider
has evaluated your travel chair and made any necessary adjustments to suit your specific
requirements. Do not change your seating configuration without first contacting Pride
Mobility Products or your authorized Pride Provider.
WARNING! Some travel chair components are heavy. You may need assistance to lift
or carry them. Please refer to the specification table for specific component weights
before you disassemble the travel chair.
WARNING! Remove the occupant from the Go-Chair before making any adjustments.
You may need the following to make comfort adjustments:
metric/standard socket set and ratchet
adjustable wrench
metric/standard hex key set
thread lock
Seat Height Adjustment
You can adjust the seat to two different heights in 1 in. (2.5-cm) increments. Seat height adjustment requires the
removal of the battery box.
To change the seat height:
1. Turn off the power to the controller.
2. Ensure the travel chair is in drive mode. See
figure 3.
3. Disconnect the controller connector from the
power base. See figure 5.
4. Remove under-seat storage.
5. Disengage the seat release lever.
6. Swivel the seat left or right and then pull it up
and off of the power base.
7. Remove the battery box.
8. Loosen the hardware at the rear of the seat
post. See figure 8
9. Pull seat post pin for height adjustment. See
figure 8.
10.Raise or lower the upper seat post to the
desired position.
11.Reinstall seat post pin.
12.Tighten the hardware at the rear of the seat
post.
13.Reinstall the battery box.
14.Reinstall the seat.
15.Reinstall under-seat storage.
16.Reconnect the controller to the power base.
NOTE: To rotate the seat, use the seat release
lever located under the front of the seat.
Figure 8. Seat Height Adjustment
Comfort Adjustments
Identification Key
1. Upper Seat Post
2. Height Adjustment Bolt
3. Lower Seat Post
4. Seat Post Securement Hardware
2
3
4
1

14
Armrest Width Adjustment
You can change each armrest’s width independently
of the other.
NOTE: Changing the armrest width may increase
the overall width of your Go-Chair.
To change the armrest width:
1. Locate the two armrest knobs on each side of
the seat frame. See figure 9.
2. Loosen the knobs and remove detent pin.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs and reinsert detent pin.
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform. See
figure 10.
To adjust the foot platform angle:
1. Flip up the foot platform and locate the adjustment
screw.
2. Turn the adjustment screw to raise or lower the
front of the foot platform. See figure 10.
Figure 9. Armrest Width Adjustment
Figure 10. Foot Platform Angle Adjustment
Identification Key
1. Armrest Knob (Located On Seat Frame)
2. Detent Pin
1
2

15
1
2
Controller Position
You can position the controller for either left-hand or
right-hand use.
WARNING! Do not place the controller
harness so that it can be pinched in
the seat frame or the power base
frame.
To change the controller position:
1. Turn off the power to the controller.
2. Cut the wire tie(s) securing the controller harness
to the armrest.
3. Flip up the armrest and loosen the setscrew. See
figure 11.
4. Slide the controller out of the armrest.
5. Loosen the setscrew in the other armrest.
6. Place the controller in the other armrest.
7. Tighten the setscrew to secure the controller.
8. Use a wire tie to secure the controller harness to
the armrest, ensuring the armrest can freely be
raised and lowered without any tension on the
harness so they do not become disconnected.
9. Plug the controller connector into the power base.
Under-seat Storage
To operate under-seat storage
1. Lift up slightly on the latch on the side of the
under-seat storage bin (See figure 12) and swing
the under-seat storage bin out and away from the
travel chair.
2. To close the under-seat storage bin, push the
under-seat storage bin toward the center of the
travel chair until you hear the latch engage.
WARNING! Ensure both under-seat
storage bins are latched prior to
operating your travel chair.
To remove the under-seat storage
1. Lift up slightly on the latch on the side of the
under-seat storage bin (See figure 12) and swing
the under-seat storage bin out and away from the
travel chair until it is fully open.
2. Lift the under-seat storage bin up and off the
travel chair.
To install the under-seat storage
1. Align the slot on the under-seat storage bin over
the securement post.
2. Lower the under-seat storage pin onto the
securement post and push the under-seat
storage bin toward the center of the travel chair
until you hear the latch engage.
Figure 11. Controller Position
Figure 12. Under-seat Storage
Identification Key
Identification Key
1. Setscrew
1. Latch
2. Securement Post
1

16
To install the positioning belt:
1. Remove the rearmost screw that holds the under-seat storage (see figure 4)hinge to the seat base
on both the left and right seat hinges.
2. Insert the screw through the supplied washer, through the positioning belt and into the seat base for
each side of the travel chair seat.
3. Tighten both screws.
To adjust the positioning belt:
1. Once seated, insert the metal tab on one side of the belt into the plastic housing on the opposite side
until you hear a click. See figure 13.
2. Pull the excess strap attached to the metal tab until it is secure, but not so tight as to cause discomfort.
To release the positioning belt:
1. Press the push button mechanism on the plastic housing.
MANDATORY! Make sure the positioning belt is properly secured to the travel chair and
is adjusted for operator comfort before each use.
MANDATORY! Inspect the positioning belt for loose parts or damage, including tears,
worn spots, bent hardware, damaged latch mechanisms, dirt or debris, before each use
of the travel chair. If you discover a problem, contact your authorized Pride Provider.
Positioning Belt
Your Go-Chair may be equipped with a positioning
belt that can be adjusted for operator comfort.
See figure 13. The positioning belt is designed to
support the operator so that he/she does not slide
down or forward in the seat. The positioning belt is
not designed for use as a restraining device.
WARNING! The positioning belt is
not designed for use as a seat belt
in a motor vehicle. Nor is your travel
chair suitable for use as a seat in
any vehicle. Anyone traveling in a
vehicle should be properly belted
into seats approved by the vehicle
manufacturer.
WARNING! The positioning belt
should be secured at all times. Never
allow the positioning belt to hang or
drag on the floor as it may become
entangled.
1
Figure 13. Positioning Belt Adjustment
Identification Key
1. Positioning Belt

17
Batteries and Charging
The Go-Chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and
maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle
batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance
to automotive batteries, they are not interchangeable. Automotive batteries are not designed to handle a
long, deep discharge, and also are unsafe for use in travel chairs.
MANDATORY! Battery posts, terminals, and related accessories contain lead
and lead compounds. Wear goggles and gloves when handling batteries and
wash hands after handling.
PROHIBITED! Always use two batteries of the exact same type, chemistry,
and amp-hour (Ah) capacity. Refer to the specifications table in this manual
and in the manual supplied with the battery charger for recommended type
and capacities.
WARNING! Contact your authorized Pride Provider if you have any questions
regarding the batteries in your travel chair.
Charging the Batteries
The battery charger is essential in providing long life for your Go-Chair batteries. It is designed to optimize
your travel chair’s performance by charging the batteries safely, quickly, and easily. The battery charger is
only functional when the charger power cord is plugged into an electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If
necessary, properly install an approved 3-pronged adapter to an electrical
outlet having 2-pronged plug access.
PROHIBITED! Never use an extension lead to plug in your battery charger.
Plug the charger directly into a properly wired standard electrical outlet.
PROHIBITED! Do not allow unsupervised children to play near the Go-Chair
while the batteries are charging. Pride recommends that you do not charge
the batteries while the travel chair is occupied.
MANDATORY! Read the battery charging instructions in this manual and in
the manual supplied with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries.
Keep the Go-Chair and battery charger away from sources of ignition such
as flames or sparks and provide adequate ventilation when charging the
batteries.
WARNING! You must recharge your Go-Chair’s batteries with the supplied off-
board charger. Do not use an automotive-type battery charger.
WARNING! Inspect the battery charger, wiring, and connectors for damage
before each use. Contact your authorized Pride Provider if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery
charger does not appear to be working correctly, contact your authorized
Pride Provider.
WARNING! Be aware that the battery charger case may become hot during
charging. Avoid skin contact and do not place on surfaces that may be
affected by the heat.
WARNING! If the battery charger is equipped with cooling slots, then do not
attempt to insert objects through these slots.
Batteries and Charging

18
WARNING! If your battery charger has not been tested and approved for
outdoor use, then do not expose it to adverse or extreme weather conditions.
If the battery charger is exposed to adverse or extreme weather conditions,
then it must be allowed to adjust to the difference in environmental conditions
before use indoors. Refer to the manual supplied with the battery charger for
more information.
NOTE: The Go-Chair batteries can be charged
with the battery box either installed on or
removed from the power base.
To charge the batteries using the off-board
charger:
1. Position the front of your travel chair next to a
standard electrical outlet.
2. Be certain the controller power is turned off and
the freewheel levers are in the engaged position.
See “Your Go-Chair.”
3. Plug the off-board charger into the off-board
charger/programming socket of the controller.
4. Plug the off-board charger into the electrical
outlet.
WARNING! The LED lights on the
charger indicate different charger
conditions at various times: charger
power on, charging in progress,
and charging complete. If the LED
does not indicate that charging is
completedwithin24hours,unplugthe
charger from the outlet and contact
your authorized Pride Provider. Refer
to the manual supplied with the
charger for a complete explanation
of these indicators.
Figure 14. Battery Charging
5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then
from the controller.
To charge the batteries with the battery box removed from the power base:
1. Remove the battery box from the power base.
2. Position the battery box next to a standard electrical outlet.
3. Plug the off-board charger into the battery box charger port. See figure 14.
4. Plug the off-board charger into the electrical outlet.
NOTE: If this is a Pride off-board charger, then there are two lights in it.The red light indicates that
power to the off-board charger is on.The green light indicates that the batteries are fully charged.
If it is not a Pride off-board charger, then follow the instructions supplied by the manufacturer.
5. When the batteries are fully charged, unplug the off-board charger from the wall outlet and then from
the battery box.
6. Reinstall the battery box to the power base.

19
Figure 15. Removal and Installation of Go-Chair Battery Box
NOTE: Turn off the power to the controller and remove the seat before removing the Go-Chair bat-
tery box.
1. TO REMOVE THE BATTERY BOX, GRASP THE BATTERY
BOX HANDLEAND LIFT UPTO DISENGAGE THE BOX FROM
THE POWER BASE.
2. TILT THE BATTERY BOX FORWARD SLIGHTLY.
3. LIFT THE BATTERY BOX AWAY FROM THE POWER BASE. 4. TO INSTALL THE BATTERY BOX, GRASPTHE BATTERYBOX
HANDLEAND TILT THE BOX FORWARD SLIGHTLY.
5. PLACE THE BATTERYBOX ON THE POWER BASE. 6. PUSH THE BACK OF THE BATTERY BOX DOWN UNTIL IT IS
FIRMLY IN PLACE.

20
Battery Break-in
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to 90% of its peak
performance level.
2. Operate your Go-Chair throughout the house and yard. Move slowly at first, and do not travel too far
until you become accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of at least 8-14 hours and operate your Go-Chair again. The
batteries will perform at over 90% of their potential.
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended
period.
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage (alternating current) and converts it to 24
VDC (direct current). The batteries use direct current to run your Go-Chair. When the battery voltage is
low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the
charger does not work as hard to complete the charging cycle. When the battery is fully charged, the
amperage from the charger is nearly at zero. This is how the charger maintains a charge but does not
overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the Go-Chair. It is the safest, most efficient tool to charge the
batteries. We do not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE:Your travel chair’s charger will not operate after the batteries have been discharged to near-
ly zero capacity. If this happens, call an authorized Pride Provider for assistance.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries.You may use your Go-Chair
all day on a daily basis or you may not use it for weeks at a time.
Daily Use
If you use your Go-Chair on a daily basis, charge the batteries as soon as you are finished using your
Go-Chair.Your Go-Chair will be ready each morning to give you a full day’s service. It is recommended
that you charge the batteries at least 8 to 14 hours after daily use. Pride recommends that you charge
your batteries for an additional 4 hours after the battery charger indicates that charging is complete.
Infrequent Use
If you use your Go-Chair infrequently (once a week or less), you should charge the batteries at least
once per week for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Refer to the
manual supplied with the battery charger for charging instructions. Pride recommends charging
your batteries for at least 48 continuous hours once per month to improve battery performance
and battery life.